* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: use linux/io.h to fix compile warnings
ALSA: hda - Fix memory leaks in conexant jack arrays
ASoC: CX20442: fix NULL pointer dereference
ASoC: Amstrad Delta: fix const related build error
ALSA: oxygen: fix output routing on Xonar DG
sound: silent echo'ed messages in Makefile
ASoC: Fix mask/val_mask confusion snd_soc_dapm_put_volsw()
ASoC: DaVinci: fix kernel panic due to uninitialized platform_data
ALSA: HDA: Fix microphone(s) on Lenovo Edge 13
ASoC: Fix module refcount for auxiliary devices
ALSA: HDA: cxt5066 - Use asus model for Asus U50F, select correct SPDIF output
ALSA: HDA: Add a new model "asus" for Conexant 5066/205xx
ALSA: HDA: Refactor some redundant code for Conexant 5066/205xx
Completed the bnx2x_set_rx_mode() to a proper netdev->ndo_set_rx_mode
implementation:
- Added a missing configuration of a unicast MAC addresses list.
- Changed bp->dma_lock from being a mutex to a spinlock as long as it's taken
under netdev->addr_list_lock now.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent packets duplication for frames targeting FCoE L2 ring:
packets were arriving to stack from both L2 RSS and from FCoE
L2 in a promiscuous mode.
Configure FCoE L2 ring to DROP_ALL rx mode, when interface is
configured to PROMISC, and to accept only unicast frames, when
interface is configured to ALL_MULTI.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always configure an FCoE L2 ring with a mini-jumbo MTU size (2500).
To do that we had to move the rx_buf_size parameter from per
function level to a per ring level.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code, and the places that set the variable
is_internal_short_scan and the vif pointers are
all protected by the mutex, there's no point in
locking the spinlock here as well (any more).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
FREQ is a ridiculously short name for a platform-specific macro in a
generic header, and it now conflicts with an enumeration in the
gspca/ov519 driver.
Also delete conditional reference to ixp4xx_get_board_tick_rate()
which is not defined anywhere.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Queues should be empty when released, if not, there is a safety valve.
Make sure the queue is usable after it triggers.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
As this function is called in some error paths while not
removing the module, the __exit attribute prevents the kernel
image from linking when btrfs is compiled in statically.
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
When btrfs_alloc_path() fails, btrfs_free_path() need not be called.
Therefore, it changes the branch ahead.
Signed-off-by: Tsutomu Itoh <t-itoh@jp.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This has been resulting in a BUT_ON(ret) after btrfs_reserve_extent in
btrfs_cow_file_range. The reason is we don't actually calculate the bytes_super
for a block group until we go to cache it, which means that the space_info can
hand out reservations for space that it doesn't actually have, and we can run
out of data space. This is also a problem if you are using space caching since
we don't ever calculate bytes_super for the block groups. So instead everytime
we read a block group call exclude_super_stripes, which calculates the
bytes_super for the block group so it can be left out of the space_info. Then
whenever caching completes we just call free_excluded_extents so that the super
excluded extents are freed up. Also if we are unmounting and we hit any block
groups that haven't been cached we still need to call free_excluded_extents to
make sure things are cleaned up properly. Thanks,
Reported-by: Arne Jansen <sensille@gmx.net>
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
When we're cleaning up the tree log we need to be able to remove free space from
the block group. The problem is if that free space spans bitmaps we would not
find the space since we're looking for too many bytes. So make sure the amount
of bytes we search for is limited to either the number of bytes we want, or the
number of bytes left in the bitmap. This was tested by a user who was hitting
the BUG() after search_bitmap. With this patch he can now mount his fs.
Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Fix memory leak in error path of sis900_rx(). If we don't do this we'll
leak the skb we dev_alloc_skb()'ed just a few lines above when the
variable goes out of scope.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Exit from parse_dacl if no memory returned from the call to kmalloc.
Signed-off-by: Stanislav Fomichev <kernel@fomichev.me>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Somehow I managed to miss the last __do_IRQ caller when I cleanup the
remaining users. m32r is fully converted to the generic irq layer, but
I managed to not commit the conversion of __do_IRQ() to
generic_handle_irq() after compile testing the quilt series :(
Pointed-out-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
The mask which filters out the valid bits which can be set via
irq_modify_status() is missing IRQ_NO_BALANCING, which breaks UV.
Add IRQ_PER_CPU as well to avoid another one line patch for 39.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The last register is at offset 0xa8 making the resource end to be 0xac - 1
instead of 0xb0 - 1.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since checkin ebba638ae7 we call
verify_cpu even in 32-bit mode. Unfortunately, calling a function
means using the stack, and the stack pointer was not initialized in
the 32-bit setup code! This code initializes the stack pointer, and
simplifies the interface slightly since it is easier to rely on just a
pointer value rather than a descriptor; we need to have different
values for the segment register anyway.
This retains start_stack as a virtual address, even though a physical
address would be more convenient for 32 bits; the 64-bit code wants
the other way around...
Reported-by: Matthieu Castet <castet.matthieu@free.fr>
LKML-Reference: <4D41E86D.8060205@free.fr>
Tested-by: Kees Cook <kees.cook@canonical.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
When the socket to the server is disconnected, the client more or less
immediately calls cifs_reconnect to reconnect the socket. The NegProt
and SessSetup however are not done until an actual call needs to be
made.
With the addition of the SMB echo code, it's possible that the server
will initiate a disconnect on an idle socket. The client will then
reconnect the socket but no NegotiateProtocol request is done. The
SMBEcho workqueue job will then eventually pop, and an SMBEcho will be
sent on the socket. The server will then reject it since no NegProt was
done.
The ideal fix would be to either have the socket not be reconnected
until we plan to use it, or to immediately do a NegProt when the
reconnect occurs. The code is not structured for this however. For now
we must just settle for not sending any echoes until the NegProt is
done.
Reported-by: JG <jg@cms.ac>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Like metrics, the ICMP rate limiting bits are cached state about
a destination. So move it into the inet_peer entries.
If an inet_peer cannot be bound (the reason is memory allocation
failure or similar), the policy is to allow.
Signed-off-by: David S. Miller <davem@davemloft.net>
Always lookup to see if we have an existing inetpeer entry for
a route. Let FLOWI_FLAG_PRECOW_METRICS merely influence the
"create" argument to rt_bind_peer().
Also, call rt_bind_peer() unconditionally since it is not
possible for rt->peer to be non-NULL at this point.
Signed-off-by: David S. Miller <davem@davemloft.net>
This should decrease un-necessary flushes, on/off channel work,
and channel changes in cases where the only scanned channel is
the current operating channel.
* Removes SCAN_OFF_CHANNEL flag, uses SDATA_STATE_OFFCHANNEL
and is-scanning flags instead.
* Add helper method to determine if we are currently configured
for the operating channel.
* Do no blindly go off/on channel in work.c Instead, only call
appropriate on/off code when we really need to change channels.
Always enable offchannel-ps mode when starting work,
and disable it when we are done.
* Consolidate ieee80211_offchannel_stop_station and
ieee80211_offchannel_stop_beaconing, call it
ieee80211_offchannel_stop_vifs instead.
* Accept non-beacon frames when scanning on operating channel.
* Scan state machine optimized to minimize on/off channel
transitions. Also, when going on-channel, go ahead and
re-enable beaconing. We're going to be there for 200ms,
so seems like some useful beaconing could happen.
Always enable offchannel-ps mode when starting software
scan, and disable it when we are done.
* Grab local->mtx earlier in __ieee80211_scan_completed_finish
so that we are protected when calling hw_config(), etc.
* Pass probe-responses up the stack if scanning on local
channel, so that mlme can take a look.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since even with the latest changes the false positive issue of the baseband
hang check is not fully solved yet, additional checks are needed.
If the baseband hang occurs, the rx_clear signal will be stuck to high, so
we can use the cycle counters to confirm it.
With this patch, a hardware reset is only triggered if the baseband hang
check returned true three times in a row, with a beacon interval between
each check and if the busy time was also 99% or more during the check
intervals.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I can't think of a valid use case for this aside from debugging (which can
also be done with a real monitor interface), and dropping these frames saves
some precious CPU cycles.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All register writes to the key cache have to be done in pairs. However,
the clearing of a separate MIC entry with hardware revisions that use
combined MIC key layout did not do that with one of the registers. Add
the matching register write to the following register to make the KEY4
register write actually complete.
This is mostly a fix for a theoretical issue since the incorrect entry
that could potentially be left behind in the key cache would not match
with received frames. Anyway, better make this code clean the entry
correctly using paired register writes.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While leaving oper channel, STA informs sleep state to AP to
stop sending data. Till sending ack for the nullfunc, AP
continues to send the data to STA which restarts ps_timer that
is causing unnecessary nullfunc exchange on timer expiry
when the STA was already moved to offchannel. So don't restart ps_timer
on data reception during scan. This issue was identified by
the following warning.
WARNING: at net/mac80211/tx.c:661 invoke_tx_handlers+0xf07/0x1330 [mac80211]
wlan0: Dropped data frame as no usable bitrate found while scanning and
associated. Target station: 00:03:7f:0b:a6:1b on 5 GHz band
Call Trace:
[<ffffffffa0413ba7>] invoke_tx_handlers+0xf07/0x1330 [mac80211]
[<ffffffffa0414056>] ieee80211_tx+0x86/0x2c0 [mac80211]
[<ffffffffa0414345>] ieee80211_xmit+0xb5/0x1d0 [mac80211]
[<ffffffffa04037e0>] ieee80211_dynamic_ps_enable_work+0x0/0xb0 [mac80211]
[<ffffffffa04158cf>] ieee80211_tx_skb+0x4f/0x60 [mac80211]
[<ffffffffa04026e6>] ieee80211_send_nullfunc+0x46/0x60 [mac80211]
[<ffffffffa0403885>] ieee80211_dynamic_ps_enable_work+0xa5/0xb0 [mac80211]
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It should be safe to enable AP-mode now.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX appears to freeze while idle. Resetting rx-urbs appears to be enough to fix
this. Do reset 30 seconds after last rx.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When driver fails to acquire device semaphore lock, device usually
freezes soon afterwards. So failing to acquire lock indicates us that
not everything is going right in device/fw. So reset device when
this happens.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When doing transfers at high speed for long time, tx queue can freeze. So add
tx watchdog. TX-watchdog checks for locked tx-urbs and reset hardware when
such is detected. Merely unlinking urb was not enough, device have to be
reseted. Hw settings are restored so that any open link will stay on after
reset.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need HW hard reset later in patchset to reset device after TX-stall.
Collect all settings that we have set to driver for later reset and
add restore function.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Device command timeouts are set up very high (1 sec) and this causes
AP beacon to lock up for long for example. Checking timeouts on device
it's easy to see that 1 sec timeout is not needed, when device fails
to response longer timeout doesn't help:
[ 473.074419] zd1211rw 1-1:1.0: print_times() Read times:
[ 473.175163] zd1211rw 1-1:1.0: print_time() 0 - 10 msec: 1506
[ 473.176429] zd1211rw 1-1:1.0: print_time() 11 - 50 msec: 0
[ 473.177955] zd1211rw 1-1:1.0: print_time() 51 - 100 msec: 0
[ 473.180703] zd1211rw 1-1:1.0: print_time() 101 - 250 msec: 0
[ 473.182101] zd1211rw 1-1:1.0: print_time() 251 - 500 msec: 0
[ 473.183221] zd1211rw 1-1:1.0: print_time() 500 - 1000 msec: 20
[ 473.184381] zd1211rw 1-1:1.0: print_time() 1000 - ... msec: 18
Also vendor driver doesn't use this long timeout. Therefore change
timeout to 50msec.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As might lower beacon update CPU usage.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use stack for allocing small < 64 byte arrays in zd_chip.c and preallocated
buffer in zd_usb.c. This might lower CPU usage for beacon setup.
v2:
- Do not use stack buffers in zd_usb.c as they would be used for urb
transfer_buffer.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Beacon config function writes beacon to hw one write per byte. This is very
slow (usually taking more than 100ms to finish) and causes high CPU usage
when in AP-mode (kworker at ~50% on Intel Atom N270). By batching commands
together zd_mac_config_beacon() runtime can be lowered to 1/5th and lower
CPU usage to saner levels (<10% on Atom).
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When doing tx/rx at high packet rate (for example simply using ping -f),
device starts to fail to respond to control messages. On non-AP modes
this only causes problems for LED updating code but when we are running
in AP-mode we are writing new beacon to HW usually every 100ms. Now if
control message fails in HW beacon setup, device lock is kept locked
and beacon data partially written. This can and usually does cause:
1. HW beacon setup fail now on, as driver cannot acquire device lock.
2. Beacon-done interrupt stop working as device has incomplete beacon.
Therefore make zd_mac_config_beacon() always try to release device lock
and add beacon watchdog to restart beaconing when stall is detected.
Also fix zd_mac_config_beacon() try acquiring device lock for max 500ms,
as what old code appeared to be trying to do using loop and msleep(1).
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On review of 'zd1211rw: implement beacon fetching and handling
ieee80211_get_buffered_bc()', Christian Lamparter noted that [1]:
Since zd_beacon_done also uploads the next beacon so long in advance,
there could be an equally long race between the outdated state of the
next beacon's DTIM broadcast traffic indicator (802.11-2007 7.3.2.6)
which -in your case- was uploaded almost a beacon interval ago and
the xmit of ieee80211_get_buffered_bc *now*.
The dtim bc/mc bit might be not set, when a mc/bc arrived after the
beacon was uploaded, but before the "beacon done event" from the
hardware. So, dozing stations don't expect the broadcast traffic
and of course, they might miss it completely.
It's probably better to fix this in mac80211 (see the attached hack).
[1] http://marc.info/?l=linux-wireless&m=129435041117256&w=2
CC: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for AP-mode beacon. Also disable beacon when interface is set
down as otherwise hw will keep flooding NEXT_BCN interrupts.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For reasons not very clear yet to me, filter_ack leaves matching tx-packet
pending with 'ack_pending'. This causes tx-packet to be passed back to upper
layer after next packet has been transfered and tx-packets might end up
coming come out of monitor interface in wrong order vs. rx.
Because of this when enable AP-mode, hostapd monitor interface would get
packets in wrong order causing problems in WPA association.
So don't use mac->ack_pending when in AP-mode.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As bss_info_changed may sleep, we can as well set RTS_CTS register right away.
Keep mac->short_preamble for later use (hw reset).
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Workers not needed anymore since configure_filter may sleep. Keep
mac->multicast_hash for later use (hw reset).
Signed-off-by: Jussi Kivilinna <jussi.kivilina@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vendor driver uses CR_BNC_INTERVAL at various places, one is HW_EnableBeacon()
that combinies beacon interval with BSS-type flag and DTIM value in upper 16bit
of u32. The other one is HW_UpdateBcnInterval() that set_aw_pt_bi()
appears to be based on. HW_UpdateBcnInterval() takes interval argument as u16
and uses that for calculations, set_aw_pt_bi() uses u32 value that has flags
and dtim in upper part. This clearly seems wrong. Also HW_UpdateBcnInterval()
updates only lower 16bit part of CR_BNC_INTERVAL. So make set_aw_pt_bi() do
calculations on only lower u16 part of s->beacon_interval.
Also set 32bit beacon interval register before reading values from device,
as HW_EnableBeacon() on vendor driver does. This is required to make beacon
work on AP-mode, simply reading and then writing updated values is not enough
at least with zd1211b.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
