This follows the ARM change c01778001a
("ARM: 6379/1: Assume new page cache pages have dirty D-cache") for the
same rationale:
There are places in Linux where writes to newly allocated page
cache pages happen without a subsequent call to flush_dcache_page()
(several PIO drivers including USB HCD). This patch changes the
meaning of PG_arch_1 to be PG_dcache_clean and always flush the
D-cache for a newly mapped page in update_mmu_cache().
This addresses issues seen with executing binaries from MMC, in
addition to some of the other HCDs that don't explicitly do cache
management for their pipe-in buffers.
Requested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: add workaround for dce3 ddc line vbios bug
drm/radeon/kms: fix interlaced and doublescan handling
drm/radeon/kms: fix typos in disabled vbios code
Revert "drm/i915/dp: use VBT provided eDP params if available"
drm/i915: Clear pfit registers when not used by any outputs
drm: record monitor status in output_poll_execute
drm: Set connector DPMS status to ON in drm_crtc_helper_set_config
drm/i915: fix regression due to ba3d8d749b
Revert "drm/radeon/kms: fix typo in r600 cs checker"
drm/i915/sdvo: Always add a 30ms delay to make SDVO TV detection reliable
MAINTAINERS: INTEL DRM DRIVERS list (intel-gfx) is subscribers-only
drm/i915/sdvo: Always fallback to querying the shared DDC line
drm/i915: Handle pagefaults in execbuffer user relocations
drm/i915/sdvo: Only enable HDMI encodings only if the commandset is supported
drm/radeon/kms: fix resume regression for some r5xx laptops
drm/radeon/kms: fix regression in rs4xx i2c setup
drm/i915: Only save/restore cursor regs if !KMS
drm/i915: Prevent integer overflow when validating the execbuffer
6xx/7xx was hitting the wrong BUS_CNTL reg and bits.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'intel/drm-intel-fixes' of /ssd/git/drm-next:
Revert "drm/i915/dp: use VBT provided eDP params if available"
drm/i915: Clear pfit registers when not used by any outputs
drm/i915: fix regression due to ba3d8d749b
* 'for_linus' of git://github.com/at91linux/linux-2.6-at91:
at91/board-yl-9200: fix typo in video support
atmel_spi: fix warning In function 'atmel_spi_dma_map_xfer'
at91/picotux200: remove commenting usb device and dataflash support
at91: rename rm9200ek and rm9200dk board file name
at91rm9200ek: fix warning: 'ek_mmc_data' defined but not used
at91rm9200dk: fix warning: 'dk_mmc_data' defined but not used
at91: Convert remaining boards to new-style UART initialization
at91: merge all at91rm9200 defconfig in one single file
Note: this patch targets 2.6.37 and tries to be as simple as possible.
That is why it adds more copy-and-paste horror into fs/compat.c and
uglifies fs/exec.c, this will be cleanuped later.
compat_copy_strings() plays with bprm->vma/mm directly and thus has
two problems: it lacks the RLIMIT_STACK check and argv/envp memory
is not visible to oom killer.
Export acct_arg_size() and get_arg_page(), change compat_copy_strings()
to use get_arg_page(), change compat_do_execve() to do acct_arg_size(0)
as do_execve() does.
Add the fatal_signal_pending/cond_resched checks into compat_count() and
compat_copy_strings(), this matches the code in fs/exec.c and certainly
makes sense.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Brad Spengler published a local memory-allocation DoS that
evades the OOM-killer (though not the virtual memory RLIMIT):
http://www.grsecurity.net/~spender/64bit_dos.c
execve()->copy_strings() can allocate a lot of memory, but
this is not visible to oom-killer, nobody can see the nascent
bprm->mm and take it into account.
With this patch get_arg_page() increments current's MM_ANONPAGES
counter every time we allocate the new page for argv/envp. When
do_execve() succeds or fails, we change this counter back.
Technically this is not 100% correct, we can't know if the new
page is swapped out and turn MM_ANONPAGES into MM_SWAPENTS, but
I don't think this really matters and everything becomes correct
once exec changes ->mm or fails.
Reported-by: Brad Spengler <spender@grsecurity.net>
Reviewed-and-discussed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Previous baud rate setting code only has been tested with 3.5M/9600/
115200/230400/460800 bps, and recently we got a 3M bps device to test,
which needs to modify current MUL register setting, and with this
patch 2.5M/2M/1.5M/1M/0.5M should also work as they just use a MUL
value scale down from 3M's.
Also got some reference register setting from silicon guys for
different baud rates, which tries to keep the pre-scalar register value
to 16.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The DFS referral parsing code does a memchr() call to find the '\\'
delimiter that separates the hostname in the referral UNC from the
sharename. It then uses that value to set the length of the hostname via
pointer subtraction. Instead of subtracting the start of the hostname
however, it subtracts the start of the UNC, which causes the code to
pass in a hostname length that is 2 bytes too long.
Regression introduced in commit 1a4240f4.
Reported-and-Tested-by: Robbert Kouprie <robbert@exx.nl>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Cc: Wang Lei <wang840925@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Steve French <sfrench@us.ibm.com>
This patch (as1437) fixes a bug in the usb-serial autosuspend
handling. Since the usb-serial core now has autosuspend support, it
must set the .supports_autosuspend member in every serial driver it
registers. Otherwise the usb_autopm_get_interface() call won't work.
This fixes Bugzilla #23012.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: stable@kernel.org
Reported-by: Kevin Smith <thirdwiggin@gmail.com>
Reported-and-tested-by: Simon Gerber <gesimu@gmail.com>
Reported-and-tested-by: Matteo Croce <matteo@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Tested on MacBookAir3,1. Without this, we get EPROTO errors when
fetching device config descriptors.
Signed-off-by: Brian Tarricone <brian@tarricone.org>
Reported-by: Benoit Gschwind <gschwind@gnu-log.net>
Tested-by: Edgar Hucek <gimli@dark-green.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the PID for the Vardaan Enterprises VEUSB422R3 USB to RS422/485
converter. It uses the same chip as the FTDI_8U232AM_PID 0x6001.
This should also work with the stable branches for:
2.6.31, 2.6.32, 2.6.33, 2.6.34, 2.6.35, 2.6.36
Signed-off-by: Jacques Viviers <jacques.viviers@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Default llseek operation behavior was changed by the patch named
"vfs: make no_llseek the default" after the yurex driver had been merged,
so the llseek to yurex is now ignored.
This patch add llseek fop with default_llseek to yurex driver
to catch up to the change.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Another variant of the RT Systems programming cable for ham radios.
Signed-off-by: Michael Stuermer <ms@mallorn.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When comparing filehandles in the helper nfs_same_file(), we should not be
using 'strncmp()': filehandles are not null terminated strings.
Instead, we should just use the existing helper nfs_compare_fh().
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
for the epson frambuffer support it's CONFIG_FB_S1D13XXX
not CONFIG_FB_S1D135XX
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
passing argument 2 of 'dma_map_single' discards qualifiers from pointer target type
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
as based on http://www.picotux.com/pt200/picotux200.pdf
these board does not have such I/O
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
to be a few more concistant with the other boards
as ek is for evaluation kit and dk for development kit
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Convert the following AT91RM9200-based boards to the new-style UART
initialization:
- Ajeco 1ARM Single Board Computer
- Sperry-Sun KAFA board
- picotux 200
Remove the deprecated at91_init_serial
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Fix kernel-doc warning for set_consumer_device_supply():
Warning(drivers/regulator/core.c:912): missing initial short description on line:
* set_consumer_device_supply: Bind a regulator to a symbolic supply
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Supply regulators are disabled only when the last
reference count is removed on the child regulator
(the use count goes from 1 to 0). This patch changes
the behaviour of enable so the supply regulator is
enabled only when the use count of the child
regulator goes from 0 to 1.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The Singular Message is 16 bits:
DEV_GRP[15:13] MT[12] RES_ID[11:4] RES_STATE[3:0]
Current implementation return immedially after sucessfuly write MSB part.
To properly set mode, we need to write the complete message ( MSB and LSB ).
In twl.h, now we have defines for PM Master module register offsets,
use it instead of hard coded 0x15/0x16.
Use "message & 0xff" to ensure we send correct value for LSB.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Lesly Arackal Manuel <leslyam@ti.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch add locks around regulator supply enable.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Integer division will truncate the result, this patch ensures we have
enough delay time for enabling regulator.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
We already have device_remove_file() in error path,
no need to call it before goto link_name_err.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
It is not used outside this driver so no need to make the symbol global.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch fixes a disable failure when regulator supply is used.
A while loop in regulator disable checks for supply pointer != NULL
but the pointer is not always updated, resulting in the while loop
running too many times causing a disable failure.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
About all options present in each file are activated
in the single file.
Signed-off-by: Eric Benard <eric@eukrea.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This reverts commit 869184a675.
This is required for the Sony Vaio Jesse was working on at the time, but
breaks most other eDP machines - machines that were working in earlier
kernels.
Reported-and-tested-by: Dave Airlie <airlied@redhat.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31188
Tested-by: Zhao Jian <jian.j.zhao@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Currently, if CONFIG_CIFS_FSCACHE is set, fscache is enabled on files opened
as read-only irrespective of the 'fsc' mount option. Fix this by enabling
fscache only if 'fsc' mount option is specified explicitly.
Remove an extraneous cFYI debug message and fix a typo while at it.
Reported-by: Jeff Layton <jlayton@redhat.com>
Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Suresh Jayaraman <sjayaraman@suse.de>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Currently, it is possible to specify 'fsc' mount option even if
CONFIG_CIFS_FSCACHE has not been set. The option is being ignored silently
while the user fscache functionality to work. Fix this by raising error when
the CONFIG option is not set.
Reported-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Suresh Jayaraman <sjayaraman@suse.de>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Add extended attribute name system.cifs_acl
Get/generate cifs/ntfs acl blob and hand over to the invoker however
it wants to parse/process it under experimental configurable option CIFS_ACL.
Do not get CIFS/NTFS ACL for xattr for attribute system.posix_acl_access
Signed-off-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Change the name of function mode_to_acl to mode_to_cifs_acl.
Handle return code in functions mode_to_cifs_acl and
cifs_acl_to_fattr.
Signed-off-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
PowerPC relies on IRQ-disable to guard against RCU quiecent states,
use the appropriate RCU call version.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This reverts commit e0fdace10e.
On-list discussion seems to suggest that the robustness fixes for printk
make this unnecessary and DaveM has also agreed in person at Kernel Summit
and on list.
The main problem with this code is once we hit a lockdep splat we always
keep oops_in_progress set, the console layer uses oops_in_progress with KMS
to decide when it should be showing the oops and not showing X, so it causes
problems around suspend/resume time when a userspace resume can cause a console
switch away from X, only if oops_in_progress is set (which is what we want
if an oops actually is in progress, but not because we had a lockdep splat
2 days prior).
Cc: David S Miller <davem@davemloft.net>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Like in the "TTY: don't allow reopen when ldisc is changing" patch,
this one fixes a TTY WARNING as described in the option 1) there:
1) __tty_hangup from tty_ldisc_hangup to tty_ldisc_enable. During this
section tty_lock is held. However tty_lock is temporarily dropped in
the middle of the function by tty_ldisc_hangup.
The fix is to introduce a new flag which we set during the unlocked
window and check it in tty_reopen too. The flag is TTY_HUPPING and is
cleared after TTY_HUPPED is set.
While at it, remove duplicate TTY_HUPPED set_bit. The one after
calling ops->hangup seems to be more correct. But anyway, we hold
tty_lock, so there should be no difference.
Also document the function it does that kind of crap.
Nicely reproducible with two forked children:
static void do_work(const char *tty)
{
if (signal(SIGHUP, SIG_IGN) == SIG_ERR) exit(1);
setsid();
while (1) {
int fd = open(tty, O_RDWR|O_NOCTTY);
if (fd < 0) continue;
if (ioctl(fd, TIOCSCTTY)) continue;
if (vhangup()) continue;
close(fd);
}
exit(0);
}
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: <Valdis.Kletnieks@vt.edu>
Reported-by: Kyle McMartin <kyle@mcmartin.ca>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are many WARNINGs like the following reported nowadays:
WARNING: at drivers/tty/tty_io.c:1331 tty_open+0x2a2/0x49a()
Hardware name: Latitude E6500
Modules linked in:
Pid: 1207, comm: plymouthd Not tainted 2.6.37-rc3-mmotm1123 #3
Call Trace:
[<ffffffff8103b189>] warn_slowpath_common+0x80/0x98
[<ffffffff8103b1b6>] warn_slowpath_null+0x15/0x17
[<ffffffff8128a3ab>] tty_open+0x2a2/0x49a
[<ffffffff810fd53f>] chrdev_open+0x11d/0x146
...
This means tty_reopen is called without TTY_LDISC set. For further
considerations, note tty_lock is held in tty_open. TTY_LDISC is cleared in:
1) __tty_hangup from tty_ldisc_hangup to tty_ldisc_enable. During this
section tty_lock is held. However tty_lock is temporarily dropped in
the middle of the function by tty_ldisc_hangup.
2) tty_release via tty_ldisc_release till the end of tty existence. If
tty->count <= 1, tty_lock is taken, TTY_CLOSING bit set and then
tty_ldisc_release called. tty_reopen checks TTY_CLOSING before checking
TTY_LDISC.
3) tty_set_ldisc from tty_ldisc_halt to tty_ldisc_enable. We:
* take tty_lock, set TTY_LDISC_CHANGING, put tty_lock
* call tty_ldisc_halt (clear TTY_LDISC), tty_lock is _not_ held
* do some other work
* take tty_lock, call tty_ldisc_enable (set TTY_LDISC), put
tty_lock
I cannot see how 2) can be a problem, as there I see no race. OTOH, 1)
and 3) can happen without problems. This patch the case 3) by checking
TTY_LDISC_CHANGING along with TTY_CLOSING in tty_reopen. 1) will be
fixed in the following patch.
Nicely reproducible with two processes:
while (1) {
fd = open("/dev/ttyS1", O_RDWR);
if (fd < 0) {
warn("open");
continue;
}
close(fd);
}
--------
while (1) {
fd = open("/dev/ttyS1", O_RDWR);
ld1 = 0; ld2 = 2;
while (1) {
ioctl(fd, TIOCSETD, &ld1);
ioctl(fd, TIOCSETD, &ld2);
}
close(fd);
}
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: <Valdis.Kletnieks@vt.edu>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We should never return positive values from ldisc->open, tty layer
doesn't (and never did) expect that.
If we do that, weird things like warnings in tty_ldisc_close happen.
Not sure if dev->base_addr is used somehow now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Andrew Hendry <andrew.hendry@gmail.com>
Cc: linux-x25@vger.kernel.org
Tested-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
