Since commit 1851617cd2 ("PCI/MSI: Disable MSI at enumeration even if
kernel doesn't support MSI"), the setup of dev->msi_cap/msix_cap and the
disable of MSI/MSI-X interrupts isn't being done at PCI probe time, as
the logic responsible for this was moved in the aforementioned commit
from pci_device_add() to pci_setup_device(). The latter function is not
reachable on PowerPC pseries platform during Open Firmware PCI probing
time.
This exhibits as drivers not being able to enable MSI, eg:
bnx2x 0000:01:00.0: no msix capability found
This patch calls pci_msi_setup_pci_dev() explicitly to disable MSI/MSI-X
during PCI probe time on pSeries platform.
Fixes: 1851617cd2 ("PCI/MSI: Disable MSI at enumeration even if kernel doesn't support MSI")
[mpe: Flesh out change log and clarify comment]
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This builds on the ability to run more than one vcore on a physical
core by using the micro-threading (split-core) modes of the POWER8
chip. Previously, only vcores from the same VM could be run together,
and (on POWER8) only if they had just one thread per core. With the
ability to split the core on guest entry and unsplit it on guest exit,
we can run up to 8 vcpu threads from up to 4 different VMs, and we can
run multiple vcores with 2 or 4 vcpus per vcore.
Dynamic micro-threading is only available if the static configuration
of the cores is whole-core mode (unsplit), and only on POWER8.
To manage this, we introduce a new kvm_split_mode struct which is
shared across all of the subcores in the core, with a pointer in the
paca on each thread. In addition we extend the core_info struct to
have information on each subcore. When deciding whether to add a
vcore to the set already on the core, we now have two possibilities:
(a) piggyback the vcore onto an existing subcore, or (b) start a new
subcore.
Currently, when any vcpu needs to exit the guest and switch to host
virtual mode, we interrupt all the threads in all subcores and switch
the core back to whole-core mode. It may be possible in future to
allow some of the subcores to keep executing in the guest while
subcore 0 switches to the host, but that is not implemented in this
patch.
This adds a module parameter called dynamic_mt_modes which controls
which micro-threading (split-core) modes the code will consider, as a
bitmap. In other words, if it is 0, no micro-threading mode is
considered; if it is 2, only 2-way micro-threading is considered; if
it is 4, only 4-way, and if it is 6, both 2-way and 4-way
micro-threading mode will be considered. The default is 6.
With this, we now have secondary threads which are the primary thread
for their subcore and therefore need to do the MMU switch. These
threads will need to be started even if they have no vcpu to run, so
we use the vcore pointer in the PACA rather than the vcpu pointer to
trigger them.
It is now possible for thread 0 to find that an exit has been
requested before it gets to switch the subcore state to the guest. In
that case we haven't added the guest's timebase offset to the
timebase, so we need to be careful not to subtract the offset in the
guest exit path. In fact we just skip the whole path that switches
back to host context, since we haven't switched to the guest context.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
When running a virtual core of a guest that is configured with fewer
threads per core than the physical cores have, the extra physical
threads are currently unused. This makes it possible to use them to
run one or more other virtual cores from the same guest when certain
conditions are met. This applies on POWER7, and on POWER8 to guests
with one thread per virtual core. (It doesn't apply to POWER8 guests
with multiple threads per vcore because they require a 1-1 virtual to
physical thread mapping in order to be able to use msgsndp and the
TIR.)
The idea is that we maintain a list of preempted vcores for each
physical cpu (i.e. each core, since the host runs single-threaded).
Then, when a vcore is about to run, it checks to see if there are
any vcores on the list for its physical cpu that could be
piggybacked onto this vcore's execution. If so, those additional
vcores are put into state VCORE_PIGGYBACK and their runnable VCPU
threads are started as well as the original vcore, which is called
the master vcore.
After the vcores have exited the guest, the extra ones are put back
onto the preempted list if any of their VCPUs are still runnable and
not idle.
This means that vcpu->arch.ptid is no longer necessarily the same as
the physical thread that the vcpu runs on. In order to make it easier
for code that wants to send an IPI to know which CPU to target, we
now store that in a new field in struct vcpu_arch, called thread_cpu.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Tested-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
If the target kernel does not inlcude the FIXUP_ENDIAN check, coming
from a different-endian kernel will cause the target kernel to panic.
All ppc64 kernels can handle starting in big-endian mode, so return to
big-endian before branching into the target kernel.
This mainly affects pseries as secondaries on powernv are returned to
OPAL.
Signed-off-by: Samuel Mendoza-Jonas <sam.mj@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pstore only supports one backend at a time. The preferred
pstore backend is set by passing the pstore.backend=<name>
argument to the kernel at boot time. Currently, while trying
to register with pstore, nvram throws an error message even
when "pstore.backend != nvram", which is unnecessary. This
patch removes the error message in case "pstore.backend != nvram".
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The patch was generated using fixed coccinelle semantic patch
scripts/coccinelle/api/memdup.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2014320
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
pcibios_set_pcie_reset_state() could be called to complete
reset request when passing through PCI device, flag
EEH_PE_ISOLATED is set before saving the PCI config sapce.
On some Broadcom adapters, EEH_PE_CFG_BLOCKED is automatically
set when the flag EEH_PE_ISOLATED is marked. It caused bogus
data saved from the PCI config space, which will be restored
to the PCI adapter after the reset. Eventually, the hardware
can't work with corrupted data in PCI config space.
The patch fixes the issue with eeh_pe_state_mark_no_cfg(), which
doesn't set EEH_PE_CFG_BLOCKED when seeing EEH_PE_ISOLATED on the
PE, in order to avoid the bogus data saved and restored to the PCI
config space.
Reported-by: Rajanikanth H. Adaveeshaiah <rajanikanth.ha@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Simplify the dma_get_required_mask call chain by moving it from pnv_phb to
pci_controller_ops, similar to commit 763d2d8df1 ("powerpc/powernv:
Move dma_set_mask from pnv_phb to pci_controller_ops").
Previous call chain:
0) call dma_get_required_mask() (kernel/dma.c)
1) call ppc_md.dma_get_required_mask, if it exists. On powernv, that
points to pnv_dma_get_required_mask() (platforms/powernv/setup.c)
2) device is PCI, therefore call pnv_pci_dma_get_required_mask()
(platforms/powernv/pci.c)
3) call phb->dma_get_required_mask if it exists
4) it only exists in the ioda case, where it points to
pnv_pci_ioda_dma_get_required_mask() (platforms/powernv/pci-ioda.c)
New call chain:
0) call dma_get_required_mask() (kernel/dma.c)
1) device is PCI, therefore call pci_controller_ops.dma_get_required_mask
if it exists
2) in the ioda case, that points to pnv_pci_ioda_dma_get_required_mask()
(platforms/powernv/pci-ioda.c)
In the p5ioc2 case, the call chain remains the same -
dma_get_required_mask() does not find either a ppc_md call or
pci_controller_ops call, so it calls __dma_get_required_mask().
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since we moved the "lock" to be the first element of
struct tlb_core_data in commit 82d86de25b ("powerpc/e6500: Make TLB
lock recursive"), this macro is not used by any code. Just delete it.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
* pci/hotplug:
PCI: pciehp: Remove ignored MRL sensor interrupt events
PCI: pciehp: Remove unused interrupt events
PCI: pciehp: Handle invalid data when reading from non-existent devices
PCI: Hold pci_slot_mutex while searching bus->slots list
PCI: Protect pci_bus->slots with pci_slot_mutex, not pci_bus_sem
PCI: pciehp: Simplify pcie_poll_cmd()
PCI: Use "slot" and "pci_slot" for struct hotplug_slot and struct pci_slot
* pci/iommu:
PCI: Remove pci_ats_enabled()
PCI: Stop caching ATS Invalidate Queue Depth
PCI: Move ATS declarations to linux/pci.h so they're all together
PCI: Clean up ATS error handling
PCI: Use pci_physfn() rather than looking up physfn by hand
PCI: Inline the ATS setup code into pci_ats_init()
PCI: Rationalize pci_ats_queue_depth() error checking
PCI: Reduce size of ATS structure elements
PCI: Embed ATS info directly into struct pci_dev
PCI: Allocate ATS struct during enumeration
iommu/vt-d: Cache PCI ATS state and Invalidate Queue Depth
* pci/irq:
PCI: Kill off set_irq_flags() usage
* pci/virtualization:
PCI: Add ACS quirks for Intel I219-LM/V
In the complete hotplug case, EEH PEs are supposed to be released
and set to NULL. Normally, this is done by eeh_remove_device(),
which is called from pcibios_release_device().
However, if something is holding a kref to the device, it will not
be released, and the PE will remain. eeh_add_device_late() has
a check for this which will explictly destroy the PE in this case.
This check in eeh_add_device_late() occurs after a call to
eeh_ops->probe(). On PowerNV, probe is a pointer to pnv_eeh_probe(),
which will exit without probing if there is an existing PE.
This means that on PowerNV, devices with outstanding krefs will not
be rediscovered by EEH correctly after a complete hotplug. This is
affecting CXL (CAPI) devices in the field.
Put the probe after the kref check so that the PE is destroyed
and affected devices are correctly rediscovered by EEH.
Fixes: d91dafc02f ("powerpc/eeh: Delay probing EEH device during hotplug")
Cc: stable@vger.kernel.org
Cc: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Replace hard coded values with existing DRCONF flags while procesing
detected LMBs from the device tree. Does not change any functionality.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The code to fetch the SLB size from the device tree wants to first look
for "slb-size" and then if that's not found "ibm,slb-size".
We can simplify the code by looking for the properties and then if we
find one of them we set mmu_slb_size.
We also change the function name from check_cpu_slb_size() to
init_mmu_slb_size() as the function doesn't check anything, it only
initialises mmu_slb_size.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
[mpe: Rewrite change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Quoting Arnd:
I was thinking the opposite approach and basically removing all uses
of IORESOURCE_CACHEABLE from the kernel. There are only a handful of
them.and we can probably replace them all with hardcoded
ioremap_cached() calls in the cases they are actually useful.
All existing usages of IORESOURCE_CACHEABLE call ioremap() instead of
ioremap_nocache() if the resource is cacheable, however ioremap() is
uncached by default. Clearly none of the existing usages care about the
cacheability. Particularly devm_ioremap_resource() never worked as
advertised since it always fell back to plain ioremap().
Clean this up as the new direction we want is to convert
ioremap_<type>() usages to memremap(..., flags).
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Migrate powerpc driver to the new 'set-state' interface provided by
clockevents core, the earlier 'set-mode' interface is marked obsolete
now.
This also enables us to implement callbacks for new states of clockevent
devices, for example: ONESHOT_STOPPED.
We weren't doing anything in ->set_mode(ONSHOT) and so
set_state_oneshot() isn't implemented.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
In CoreNet systems it is not allowed to mix M and non-M mappings to the
same memory, and coherent DMA accesses are considered to be M mappings
for this purpose. Ignoring this has been observed to cause hard
lockups in non-SMP kernels on e6500.
Furthermore, e6500 implements the LRAT (logical to real address table)
which allows KVM guests to control the WIMGE bits. This means that
KVM cannot force the M bit on the way it usually does, so the guest had
better set it itself.
Signed-off-by: Scott Wood <scottwood@freescale.com>
This function can leak kernel stack data when the user siginfo_t has a
positive si_code value. The top 16 bits of si_code descibe which fields
in the siginfo_t union are active, but they are treated inconsistently
between copy_siginfo_from_user32, copy_siginfo_to_user32 and
copy_siginfo_to_user.
copy_siginfo_from_user32 is called from rt_sigqueueinfo and
rt_tgsigqueueinfo in which the user has full control overthe top 16 bits
of si_code.
This fixes the following information leaks:
x86: 8 bytes leaked when sending a signal from a 32-bit process to
itself. This leak grows to 16 bytes if the process uses x32.
(si_code = __SI_CHLD)
x86: 100 bytes leaked when sending a signal from a 32-bit process to
a 64-bit process. (si_code = -1)
sparc: 4 bytes leaked when sending a signal from a 32-bit process to a
64-bit process. (si_code = any)
parsic and s390 have similar bugs, but they are not vulnerable because
rt_[tg]sigqueueinfo have checks that prevent sending a positive si_code
to a different process. These bugs are also fixed for consistency.
Signed-off-by: Amanieu d'Antras <amanieu@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a new powerpc-specific trace clock using the timebase register,
similar to x86-tsc. This gives us
- a fast, monotonic, hardware clock source for trace entries, and
- a clock that can be used to correlate events across cpus as well as across
hypervisor and guests.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use %pR to simplify the debug code. This also make the debug info more
readable.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
[mpe: Unsplit multi-line printk strings]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since we've already stepped away from ENABLE is a JMP and DISABLE is a
NOP with the branch_default bits, and are going to make it even worse,
rename it to make it all clearer.
This way we don't mix multiple levels of logic attributes, but have a
plain 'physical' name for what the current instruction patching status
of a jump label is.
This is a first step in removing the naming confusion that has led to
a stream of avoidable bugs such as:
a833581e37 ("x86, perf: Fix static_key bug in load_mm_cr4()")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
[ Beefed up the changelog. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Previously, pci_setup_device() and similar functions searched the
pci_bus->slots list without any locking. It was possible for another
thread to update the list while we searched it.
Add pci_dev_assign_slot() to search the list while holding pci_slot_mutex.
[bhelgaas: changelog, fold in CONFIG_SYSFS fix]
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This commit enables seccomp filter on powerpc, now that we have all the
necessary pieces in place.
To support seccomp's desire to modify the syscall return value under
some circumstances, we use a different ABI to the ptrace ABI. That is we
use r3 as the syscall return value, and orig_gpr3 is the first syscall
parameter.
This means the seccomp code, or a ptracer via SECCOMP_RET_TRACE, will
see -ENOSYS preloaded in r3. This is identical to the behaviour on x86,
and allows seccomp or the ptracer to either leave the -ENOSYS or change
it to something else, as well as rejecting or not the syscall by
modifying r0.
If seccomp does not reject the syscall, we restore the register state to
match what ptrace and audit expect, ie. r3 is the first syscall
parameter again. We do this restore using orig_gpr3, which may have been
modified by seccomp, which allows seccomp to modify the first syscall
paramater and allow the syscall to proceed.
We need to #ifdef the the additional handling of r3 for seccomp, so move
it all out of line.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Kees Cook <keescook@chromium.org>
SIG_SYS was added in commit a0727e8ce5 "signal, x86: add SIGSYS info
and make it synchronous."
Because we use the asm-generic struct siginfo, we got support for
SIG_SYS for free as part of that commit.
However there was no compat handling added for powerpc. That means we've
been advertising the existence of signfo._sifields._sigsys to compat
tasks, but not actually filling in the fields correctly.
Luckily it looks like no one has noticed, presumably because the only
user of SIGSYS in the kernel is seccomp filter, which we don't support
yet.
So before we enable seccomp filter, add compat handling for SIGSYS.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Kees Cook <keescook@chromium.org>
The API for calling do_syscall_trace_enter() is currently sensible
enough, it just returns the (modified) syscall number.
However once we enable seccomp filter it will get more complicated. When
seccomp filter runs, the seccomp kernel code (via SECCOMP_RET_ERRNO), or
a ptracer (via SECCOMP_RET_TRACE), may reject the syscall and *may* or may
*not* set a return value in r3.
That means the assembler that calls do_syscall_trace_enter() can not
blindly return ENOSYS, it needs to only return ENOSYS if a return value
has not already been set.
There is no way to implement that logic with the current API. So change
the do_syscall_trace_enter() API to make it deal with the return code
juggling, and the assembler can then just return whatever return code it
is given.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Kees Cook <keescook@chromium.org>
Currently on powerpc we have our own #define for the highest (negative)
errno value, called _LAST_ERRNO. This is defined to be 516, for reasons
which are not clear.
The generic code, and x86, use MAX_ERRNO, which is defined to be 4095.
In particular seccomp uses MAX_ERRNO to restrict the value that a
seccomp filter can return.
Currently with the mismatch between _LAST_ERRNO and MAX_ERRNO, a seccomp
tracer wanting to return 600, expecting it to be seen as an error, would
instead find on powerpc that userspace sees a successful syscall with a
return value of 600.
To avoid this inconsistency, switch powerpc to use MAX_ERRNO.
We are somewhat confident that generic syscalls that can return a
non-error value above negative MAX_ERRNO have already been updated to
use force_successful_syscall_return().
I have also checked all the powerpc specific syscalls, and believe that
none of them expect to return a non-error value between -MAX_ERRNO and
-516. So this change should be safe ...
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Kees Cook <keescook@chromium.org>
Move the now generic definitions of atomic_{set,clear}_mask() into
linux/atomic.h to avoid endless and pointless repetition.
Also, provide an atomic_andnot() wrapper for those few archs that can
implement that.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When we scan a PCI bus, we read PCI-PCI bridge window registers with
pci_read_bridge_bases() so we can validate the resource hierarchy. Most
architectures call pci_read_bridge_bases() from pcibios_fixup_bus(), but
PCI-PCI bridges are not arch-specific, so this doesn't need to be in
arch-specific code.
Call pci_read_bridge_bases() directly from the PCI core instead of from
arch code.
For alpha and mips, we now call pci_read_bridge_bases() always; previously
we only called it if PCI_PROBE_ONLY was set.
[bhelgaas: changelog]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Ralf Baechle <ralf@linux-mips.org>
CC: James E.J. Bottomley <jejb@parisc-linux.org>
CC: Michael Ellerman <mpe@ellerman.id.au>
CC: Bjorn Helgaas <bhelgaas@google.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: David Howells <dhowells@redhat.com>
CC: Russell King <linux@arm.linux.org.uk>
CC: Tony Luck <tony.luck@intel.com>
CC: David S. Miller <davem@davemloft.net>
CC: Ingo Molnar <mingo@redhat.com>
CC: Guenter Roeck <linux@roeck-us.net>
CC: Michal Simek <monstr@monstr.eu>
CC: Chris Zankel <chris@zankel.net>
The EPOW interrupt handler uses rtas_get_sensor(), which in turn
uses rtas_busy_delay() to wait for RTAS becoming ready in case it
is necessary. But rtas_busy_delay() is annotated with might_sleep()
and thus may not be used by interrupts handlers like the EPOW handler!
This leads to the following BUG when CONFIG_DEBUG_ATOMIC_SLEEP is
enabled:
BUG: sleeping function called from invalid context at arch/powerpc/kernel/rtas.c:496
in_atomic(): 1, irqs_disabled(): 1, pid: 0, name: swapper/1
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.2.0-rc2-thuth #6
Call Trace:
[c00000007ffe7b90] [c000000000807670] dump_stack+0xa0/0xdc (unreliable)
[c00000007ffe7bc0] [c0000000000e1f14] ___might_sleep+0x134/0x180
[c00000007ffe7c20] [c00000000002aec0] rtas_busy_delay+0x30/0xd0
[c00000007ffe7c50] [c00000000002bde4] rtas_get_sensor+0x74/0xe0
[c00000007ffe7ce0] [c000000000083264] ras_epow_interrupt+0x44/0x450
[c00000007ffe7d90] [c000000000120260] handle_irq_event_percpu+0xa0/0x300
[c00000007ffe7e70] [c000000000120524] handle_irq_event+0x64/0xc0
[c00000007ffe7eb0] [c000000000124dbc] handle_fasteoi_irq+0xec/0x260
[c00000007ffe7ef0] [c00000000011f4f0] generic_handle_irq+0x50/0x80
[c00000007ffe7f20] [c000000000010f3c] __do_irq+0x8c/0x200
[c00000007ffe7f90] [c0000000000236cc] call_do_irq+0x14/0x24
[c00000007e6f39e0] [c000000000011144] do_IRQ+0x94/0x110
[c00000007e6f3a30] [c000000000002594] hardware_interrupt_common+0x114/0x180
Fix this issue by introducing a new rtas_get_sensor_fast() function
that does not use rtas_busy_delay() - and thus can only be used for
sensors that do not cause a BUSY condition - known as "fast" sensors.
The EPOW sensor is defined to be "fast" in sPAPR - mpe.
Fixes: 587f83e8dd ("powerpc/pseries: Use rtas_get_sensor in RAS code")
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
rtas.h already has some nice #defines for RTAS return status
codes - let's use them instead of hard-coded "magic" values!
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds one helper function 'sigcontext_vmx_regs' which computes
quad word aligned pointer for 'vmx_reserve' array element in sigcontext
structure making the code more readable.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
[mpe: Reword comment and fix build for CONFIG_ALTIVEC=n]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently tm_orig_msr is getting used during process context switch only.
Then there is ckpt_regs which saves the checkpointed userspace context
The MSR slot contained in ckpt_regs structure can be used during process
context switch instead of tm_orig_msr, thus allowing us to drop it from
thread_struct structure. This patch does that change.
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
enable_kernel_vsx() function was commented since anything was using
it. However, vmx-crypto driver uses VSX instructions which are
only available if VSX is enable. Otherwise it rises an exception oops.
This patch uncomment enable_kernel_vsx() routine and makes it available.
Signed-off-by: Leonidas S. Barbosa <leosilva@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The encoding of the lengths in the ibm_architecture_vec array is
"interesting" to say the least. It's non-obvious how the number of bytes
we provide relates to the length value.
In fact we already got it wrong once, see 11e9ed43ca "Fix up
ibm_architecture_vec definition".
So add some macros to make it (hopefully) clearer. These at least have
the property that the integer present in the code is equal to the number
of bytes that follows it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Stewart Smith <stewart@linux.vnet.ibm.com>
This patch adds the ability to the DMA direct ops to fallback to the IOMMU
ops for coherent alloc/free if the coherent mask of the device isn't
suitable for accessing the direct DMA space and the device also happens
to have an active IOMMU table.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
core_idle_state is maintained for each core. It uses 0-7 bits to track
whether a thread in the core has entered fastsleep or winkle. 8th bit is
used as a lock bit.
The lock bit is set in these 2 scenarios-
- The thread is first in subcore to wakeup from sleep/winkle.
- If its the last thread in the core about to enter sleep/winkle
While the lock bit is set, if any other thread in the core wakes up, it
loops until the lock bit is cleared before proceeding in the wakeup
path. This helps prevent race conditions w.r.t fastsleep workaround and
prevents threads from switching to process context before core/subcore
resources are restored.
But, in the path to sleep/winkle entry, we currently don't check for
lock-bit. This exposes us to following race when running with subcore
on-
First thread in the subcorea Another thread in the same
waking up core entering sleep/winkle
lwarx r15,0,r14
ori r15,r15,PNV_CORE_IDLE_LOCK_BIT
stwcx. r15,0,r14
[Code to restore subcore state]
lwarx r15,0,r14
[clear thread bit]
stwcx. r15,0,r14
andi. r15,r15,PNV_CORE_IDLE_THREAD_BITS
stw r15,0(r14)
Here, after the thread entering sleep clears its thread bit in
core_idle_state, the value is overwritten by the thread waking up.
In such cases when the core enters fastsleep, code mistakes an idle
thread as running. Because of this, the first thread waking up from
fastsleep which is supposed to resync timebase skips it. So we can
end up having a core with stale timebase value.
This patch fixes the above race by looping on the lock bit even while
entering the idle states.
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Fixes: 7b54e9f213f76 'powernv/powerpc: Add winkle support for offline cpus'
Cc: stable@vger.kernel.org # 3.19+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This means the 'M' flag will work properly when the kernel prints a backtrace.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0BDx
-----END PGP SIGNATURE-----
Merge tag 'module_init-device_initcall-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull module_init replacement part one from Paul Gortmaker:
"Replace module_init with equivalent device_initcall in non modules.
This series of commits converts non-modular code that is using the
module_init() call to hook itself into the system to instead use
device_initcall().
The conversion is a runtime no-op, since module_init actually becomes
__initcall in the non-modular case, and that in turn gets mapped onto
device_initcall. A couple files show a larger negative diffstat,
representing ones that had a module_exit function that we remove here
vs previously relying on the linker to dispose of it.
We make this conversion now, so that we can relocate module_init from
init.h into module.h in the future.
The files changed here are just limited to those that would otherwise
have to add module.h to obviously non-modular code, in order to avoid
a compile fail, as testing has shown"
* tag 'module_init-device_initcall-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
MIPS: don't use module_init in non-modular cobalt/mtd.c file
drivers/leds: don't use module_init in non-modular leds-cobalt-raq.c
cris: don't use module_init for non-modular core eeprom.c code
tty/metag_da: Avoid module_init/module_exit in non-modular code
drivers/clk: don't use module_init in clk-nomadik.c which is non-modular
xtensa: don't use module_init for non-modular core network.c code
sh: don't use module_init in non-modular psw.c code
mn10300: don't use module_init in non-modular flash.c code
parisc64: don't use module_init for non-modular core perf code
parisc: don't use module_init for non-modular core pdc_cons code
cris: don't use module_init for non-modular core intmem.c code
ia64: don't use module_init in non-modular sim/simscsi.c code
ia64: don't use module_init for non-modular core kernel/mca.c code
arm: don't use module_init in non-modular mach-vexpress/spc.c code
powerpc: don't use module_init in non-modular 83xx suspend code
powerpc: use device_initcall for registering rtc devices
x86: don't use module_init in non-modular devicetree.c code
x86: don't use module_init in non-modular intel_mid_vrtc.c
A whole lot of bug fixes. Nothing stands out here except the ability to
enable CONFIG_OF on every architecture, and an import of a newer version
of dtc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tm5y
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux
Pull devicetree updates from Grant Likely:
"A whole lot of bug fixes.
Nothing stands out here except the ability to enable CONFIG_OF on
every architecture, and an import of a newer version of dtc"
* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux: (22 commits)
of/irq: Rename "intc_desc" to "of_intc_desc" to fix OF on sh
of/irq: Fix pSeries boot failure
Documentation: DT: Fix a typo in the filename "lantiq,<chip>-pinumx.txt"
of: define of_find_node_by_phandle for !CONFIG_OF
of/address: use atomic allocation in pci_register_io_range()
of: Add vendor prefix for Zodiac Inflight Innovations
dt/fdt: add empty versions of early_init_dt_*_memory_arch
of: clean-up unnecessary libfdt include paths
of: make unittest select OF_EARLY_FLATTREE instead of depend on it
of: make CONFIG_OF user selectable
MIPS: prepare for user enabling of CONFIG_OF
of/fdt: fix argument name and add comments of unflatten_dt_node()
of: return NUMA_NO_NODE from fallback of_node_to_nid()
tps6507x.txt: Remove executable permission
of/overlay: Grammar s/an negative/a negative/
of/fdt: Make fdt blob input parameters of unflatten functions const
of: add helper function to retrive match data
of: Grammar s/property exist/property exists/
of: Move OF flags to be visible even when !CONFIG_OF
scripts/dtc: Update to upstream version 9d3649bd3be245c9
...
This replaces the plain loop over the sglist array with for_each_sg()
macro which consists of sg_next() function calls. Since powerpc does
select ARCH_HAS_SG_CHAIN, it is necessary to use for_each_sg() in order
to loop over each sg element. This also help find problems with drivers
that do not properly initialize their sg tables when CONFIG_DEBUG_SG is
enabled.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- CPU ops and PSCI (Power State Coordination Interface) refactoring
following the merging of the arm64 ACPI support, together with
handling of Trusted (secure) OS instances
- Using fixmap for permanent FDT mapping, removing the initial dtb
placement requirements (within 512MB from the start of the kernel
image). This required moving the FDT self reservation out of the
memreserve processing
- Idmap (1:1 mapping used for MMU on/off) handling clean-up
- Removing flush_cache_all() - not safe on ARM unless the MMU is off.
Last stages of CPU power down/up are handled by firmware already
- "Alternatives" (run-time code patching) refactoring and support for
immediate branch patching, GICv3 CPU interface access
- User faults handling clean-up
And some fixes:
- Fix for VDSO building with broken ELF toolchains
- Fixing another case of init_mm.pgd usage for user mappings (during
ASID roll-over broadcasting)
- Fix for FPSIMD reloading after CPU hotplug
- Fix for missing syscall trace exit
- Workaround for .inst asm bug
- Compat fix for switching the user tls tpidr_el0 register
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YeGl
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
"Mostly refactoring/clean-up:
- CPU ops and PSCI (Power State Coordination Interface) refactoring
following the merging of the arm64 ACPI support, together with
handling of Trusted (secure) OS instances
- Using fixmap for permanent FDT mapping, removing the initial dtb
placement requirements (within 512MB from the start of the kernel
image). This required moving the FDT self reservation out of the
memreserve processing
- Idmap (1:1 mapping used for MMU on/off) handling clean-up
- Removing flush_cache_all() - not safe on ARM unless the MMU is off.
Last stages of CPU power down/up are handled by firmware already
- "Alternatives" (run-time code patching) refactoring and support for
immediate branch patching, GICv3 CPU interface access
- User faults handling clean-up
And some fixes:
- Fix for VDSO building with broken ELF toolchains
- Fix another case of init_mm.pgd usage for user mappings (during
ASID roll-over broadcasting)
- Fix for FPSIMD reloading after CPU hotplug
- Fix for missing syscall trace exit
- Workaround for .inst asm bug
- Compat fix for switching the user tls tpidr_el0 register"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (42 commits)
arm64: use private ratelimit state along with show_unhandled_signals
arm64: show unhandled SP/PC alignment faults
arm64: vdso: work-around broken ELF toolchains in Makefile
arm64: kernel: rename __cpu_suspend to keep it aligned with arm
arm64: compat: print compat_sp instead of sp
arm64: mm: Fix freeing of the wrong memmap entries with !SPARSEMEM_VMEMMAP
arm64: entry: fix context tracking for el0_sp_pc
arm64: defconfig: enable memtest
arm64: mm: remove reference to tlb.S from comment block
arm64: Do not attempt to use init_mm in reset_context()
arm64: KVM: Switch vgic save/restore to alternative_insn
arm64: alternative: Introduce feature for GICv3 CPU interface
arm64: psci: fix !CONFIG_HOTPLUG_CPU build warning
arm64: fix bug for reloading FPSIMD state after CPU hotplug.
arm64: kernel thread don't need to save fpsimd context.
arm64: fix missing syscall trace exit
arm64: alternative: Work around .inst assembler bugs
arm64: alternative: Merge alternative-asm.h into alternative.h
arm64: alternative: Allow immediate branch as alternative instruction
arm64: Rework alternate sequence for ARM erratum 845719
...
- Disable the 32-bit vdso when building LE, so we can build with a 64-bit only
toolchain.
- EEH fixes from Gavin & Richard.
- Enable the sys_kcmp syscall from Laurent.
- Sysfs control for fastsleep workaround from Shreyas.
- Expose OPAL events as an irq chip by Alistair.
- MSI ops moved to pci_controller_ops by Daniel.
- Fix for kernel to userspace backtraces for perf from Anton.
- Merge pseries and pseries_le defconfigs from Cyril.
- CXL in-kernel API from Mikey.
- OPAL prd driver from Jeremy.
- Fix for DSCR handling & tests from Anshuman.
- Powernv flash mtd driver from Cyril.
- Dynamic DMA Window support on powernv from Alexey.
- LLVM clang fixes & workarounds from Anton.
- Reworked version of the patch to abort syscalls when transactional.
- Fix the swap encoding to support 4TB, from Aneesh.
- Various fixes as usual.
- Freescale updates from Scott: Highlights include more 8xx optimizations, an
e6500 hugetlb optimization, QMan device tree nodes, t1024/t1023 support, and
various fixes and cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=d9Wh
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc updates from Michael Ellerman:
- disable the 32-bit vdso when building LE, so we can build with a
64-bit only toolchain.
- EEH fixes from Gavin & Richard.
- enable the sys_kcmp syscall from Laurent.
- sysfs control for fastsleep workaround from Shreyas.
- expose OPAL events as an irq chip by Alistair.
- MSI ops moved to pci_controller_ops by Daniel.
- fix for kernel to userspace backtraces for perf from Anton.
- merge pseries and pseries_le defconfigs from Cyril.
- CXL in-kernel API from Mikey.
- OPAL prd driver from Jeremy.
- fix for DSCR handling & tests from Anshuman.
- Powernv flash mtd driver from Cyril.
- dynamic DMA Window support on powernv from Alexey.
- LLVM clang fixes & workarounds from Anton.
- reworked version of the patch to abort syscalls when transactional.
- fix the swap encoding to support 4TB, from Aneesh.
- various fixes as usual.
- Freescale updates from Scott: Highlights include more 8xx
optimizations, an e6500 hugetlb optimization, QMan device tree nodes,
t1024/t1023 support, and various fixes and cleanup.
* tag 'powerpc-4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (180 commits)
cxl: Fix typo in debug print
cxl: Add CXL_KERNEL_API config option
powerpc/powernv: Fix wrong IOMMU table in pnv_ioda_setup_bus_dma()
powerpc/mm: Change the swap encoding in pte.
powerpc/mm: PTE_RPN_MAX is not used, remove the same
powerpc/tm: Abort syscalls in active transactions
powerpc/iommu/ioda2: Enable compile with IOV=on and IOMMU_API=off
powerpc/include: Add opal-prd to installed uapi headers
powerpc/powernv: fix construction of opal PRD messages
powerpc/powernv: Increase opal-irqchip initcall priority
powerpc: Make doorbell check preemption safe
powerpc/powernv: pnv_init_idle_states() should only run on powernv
macintosh/nvram: Remove as unused
powerpc: Don't use gcc specific options on clang
powerpc: Don't use -mno-strict-align on clang
powerpc: Only use -mtraceback=no, -mno-string and -msoft-float if toolchain supports it
powerpc: Only use -mabi=altivec if toolchain supports it
powerpc: Fix duplicate const clang warning in user access code
vfio: powerpc/spapr: Support Dynamic DMA windows
vfio: powerpc/spapr: Register memory and define IOMMU v2
...
Pull crypto update from Herbert Xu:
"Here is the crypto update for 4.2:
API:
- Convert RNG interface to new style.
- New AEAD interface with one SG list for AD and plain/cipher text.
All external AEAD users have been converted.
- New asymmetric key interface (akcipher).
Algorithms:
- Chacha20, Poly1305 and RFC7539 support.
- New RSA implementation.
- Jitter RNG.
- DRBG is now seeded with both /dev/random and Jitter RNG. If kernel
pool isn't ready then DRBG will be reseeded when it is.
- DRBG is now the default crypto API RNG, replacing krng.
- 842 compression (previously part of powerpc nx driver).
Drivers:
- Accelerated SHA-512 for arm64.
- New Marvell CESA driver that supports DMA and more algorithms.
- Updated powerpc nx 842 support.
- Added support for SEC1 hardware to talitos"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (292 commits)
crypto: marvell/cesa - remove COMPILE_TEST dependency
crypto: algif_aead - Temporarily disable all AEAD algorithms
crypto: af_alg - Forbid the use internal algorithms
crypto: echainiv - Only hold RNG during initialisation
crypto: seqiv - Add compatibility support without RNG
crypto: eseqiv - Offer normal cipher functionality without RNG
crypto: chainiv - Offer normal cipher functionality without RNG
crypto: user - Add CRYPTO_MSG_DELRNG
crypto: user - Move cryptouser.h to uapi
crypto: rng - Do not free default RNG when it becomes unused
crypto: skcipher - Allow givencrypt to be NULL
crypto: sahara - propagate the error on clk_disable_unprepare() failure
crypto: rsa - fix invalid select for AKCIPHER
crypto: picoxcell - Update to the current clk API
crypto: nx - Check for bogus firmware properties
crypto: marvell/cesa - add DT bindings documentation
crypto: marvell/cesa - add support for Kirkwood and Dove SoCs
crypto: marvell/cesa - add support for Orion SoCs
crypto: marvell/cesa - add allhwsupport module parameter
crypto: marvell/cesa - add support for all armada SoCs
...
Merge the mvebu/drivers branch of the arm-soc tree which contains
just a single patch bfa1ce5f38 ("bus:
mvebu-mbus: add mv_mbus_dram_info_nooverlap()") that happens to be
a prerequisite of the new marvell/cesa crypto driver.
Freescale updates from Scott:
"Highlights include more 8xx optimizations, an e6500 hugetlb optimization,
QMan device tree nodes, t1024/t1023 support, and various fixes and
cleanup."
This patch changes the syscall handler to doom (tabort) active
transactions when a syscall is made and return very early without
performing the syscall and keeping side effects to a minimum (no CPU
accounting or system call tracing is performed). Also included is a
new HWCAP2 bit, PPC_FEATURE2_HTM_NOSC, to indicate this
behaviour to userspace.
Currently, the system call instruction automatically suspends an
active transaction which causes side effects to persist when an active
transaction fails.
This does change the kernel's behaviour, but in a way that was
documented as unsupported. It doesn't reduce functionality as
syscalls will still be performed after tsuspend; it just requires that
the transaction be explicitly suspended. It also provides a
consistent interface and makes the behaviour of user code
substantially the same across powerpc and platforms that do not
support suspended transactions (e.g. x86 and s390).
Performance measurements using
http://ozlabs.org/~anton/junkcode/null_syscall.c indicate the cost of
a normal (non-aborted) system call increases by about 0.25%.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently these two RTC devices are in core platform code
where it is not possible for them to be modular. It will
never be modular, so using module_init as an alias for
__initcall can be somewhat misleading.
Fix this up now, so that we can relocate module_init from
init.h into module.h in the future. If we don't do this, we'd
have to add module.h to obviously non-modular code, and that
would be a worse thing.
Note that direct use of __initcall is discouraged, vs. one
of the priority categorized subgroups. As __initcall gets
mapped onto device_initcall, our use of device_initcall
directly in this change means that the runtime impact is
zero -- they will remain at level 6 in initcall ordering.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Geoff Levand <geoff@infradead.org>
Acked-by: Geoff Levand <geoff@infradead.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
