Every RCU stall need to be debugged, So collect the ram
dumps on every RCU stall to debug further by inducing
non secure watchdog bite whenever rcu stall detected.
Change-Id: I6c1cfddc92f06b48c3f22fe9970b70f2ec670bf6
Signed-off-by: Prasad Sodagudi <psodagud@codeaurora.org>
For every __pm_stay_awake call, there must be a
__pm_relax call to ensure there is no stale
wakelock is held. with the current logic
__pm_stay_awake is called whenever wakelock ref
cnt is non-zero and released only when it is 0.
This leads to wakelock being held even when
it is not required. Make a change to acquire
wakelock only when it is not held previously.
Change-Id: I8c61c184506c705fd5866de8a606f642c5de3d5b
Acked-by: Chaitanya Pratapa <cpratapa@qti.qualcomm.com>
Signed-off-by: Utkarsh Saxena <usaxena@codeaurora.org>
Add routing controls to connect analog and digital codecs for both
RX and TX paths.
CRs-Fixed: 2014602
Change-Id: Ie92f93a7cdc5230cdd5d1bc2471d96117013a34c
Signed-off-by: Walter Yang <yandongy@codeaurora.org>
Add support for required node for audio of sdm630 qrd
with internal codec.
CRs-Fixed: 2005884
Change-Id: Ia6749d8dcc36910212f7a4f755e7e0620b43da1c
Signed-off-by: Walter Yang <yandongy@codeaurora.org>
This change enables midframe sampling timer which samples
the GPU power stats if the command batch expiry takes longer
than the threshold set by KGSL_GOVERNOR_CALL_INTERVAL. This
will help the use cases where long running command batches
were delaying GPU DCVS decision for increasing the frequency.
Change-Id: I08ec8f3389c2140e1205096abc2c01f2d3882abc
Signed-off-by: Deepak Kumar <dkumar@codeaurora.org>
During the suspend flow, wil6210 HW can send sporadic interrupts,
while PCIe bus is not operational.
To prevent that, keep the interrupts disabled during the suspend
flow and re-enable them only after PCIe enablement in resume.
Change-Id: I205f8cdb89c4f64ecac4ca3422767bfc47ec3d33
Signed-off-by: Maya Erez <merez@codeaurora.org>
On sdm630, There is leakage of ~300-400uA current in Bluetooth page scan
scenarios when L6/L9/L19 follow HW_EN1.
Change-Id: Ia041245f4c3cb96373f53dd9c11e2e1249da96ae
Signed-off-by: Rupesh Tatiya <rtatiya@codeaurora.org>
Fix buffer overflow issue in synaptics touch driver while copying
the contents of "strptr" into "firmware_id". This code change is
meant to fix the same.
Change-Id: I8ea96af558eff540a37fb8e7da730c74502622aa
Signed-off-by: Shantanu Jain <shjain@codeaurora.org>
From bus driver, use aggre2_noc voter clock handle for voting
instead of using direct aggre2_noc clock, as this clock
can be enabled/disabled/set_rate from multiple clients.
Change-Id: I247f12c90b9b9900ebd9785454e8bd2b9dc13b96
Signed-off-by: Amit Nischal <anischal@codeaurora.org>
Following changes been made to improve soft fault detection,
which will fix un clocked register access in dispatcher_do_fault()
and incorrect declaration of GPU soft fault.
i) Stop fault timer before entering to NAP state
ii) Don’t start fault timer if the dispatcher inflight count is zero
iii) Add ringbuffer empty check in _isidle()
iv) Add device state check in dispatcher_do_fault()
CRs-Fixed: 2012731
Change-Id: I5ce498029f389eeeb428b4ac7fb07afd84d5764c
Signed-off-by: Hareesh Gundu <hareeshg@codeaurora.org>
Clear ICE configuration once cmdq request processing is done.
This ensures that the key information is cleared by ICE driver.
This call is optional for FDE but required for FBE.
Change-Id: I231ca849aa34c156baa45fceae95debf46dd57f0
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Adding support for clearing ice configuration.
Once mmc request processing is completed, mmc driver has to
call config_end to ensure key information is cleared by ICE
driver. This call is optional for FDE but required for FBE.
Change-Id: I8c225deda782528a7f220f7d1f81c6240caca1ae
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Update the driver to support PM660. PM660 add dedicated
register for auto-resonance control and a few other changes
to haptics configuration.
CRs-Fixed: 2016588
Change-Id: Ia9d65bc0a1169b5cba1c122d50d49c8102ac79f5
Signed-off-by: Ankit Sharma <ansharma@codeaurora.org>
Update the adapter allowance configuration from 5_TO_9V
continuous mode to 5_OR_9V discrete mode, this allows
hardware to detect Over-voltage for 5V adapter.
CRs-Fixed: 1104289
Change-Id: Ie43febb92e5a6e52ce17779d8cea91cbdd2011cb
Signed-off-by: Ashay Jaiswal <ashayj@codeaurora.org>
Handle LPM when one of the session goes to sleep.
when LPM enable unvote ab/ib of inative session and
vice versa.
Change-Id: I72ab333b24d7ad5ae4deafa758e7e2d92f3cc9d2
Signed-off-by: Ramesh V <ramev@codeaurora.org>
QPNP_MISC driver provides support to read the registers or
support functions required on certain PMICs. Enable it.
Change-Id: Ib496506e60dc94dec1b2292bf0e6fd01583e2f75
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
saved_tgids memory was not freed in free_saved_cmdlines_buffer
which can cause memory-leak when /d/tracing/saved_cmdlines_size
node value is changed. Fix it by freeing saved_tgids
in free_saved_cmdlines_buffer.
Change-Id: I006870c858b7306b7d9c840b7712061985dda310
Signed-off-by: Omprakash Dhyade <odhyade@codeaurora.org>
