* samsung/dt: (27 commits)
ARM: dts: Add intial dts file for EXYNOS4210 SoC, SMDKV310 and ORIGEN
ARM: EXYNOS: Add Exynos4 device tree enabled board file
rtc: rtc-s3c: Add device tree support
input: samsung-keypad: Add device tree support
ARM: S5PV210: Modify platform data for pl330 driver
ARM: S5PC100: Modify platform data for pl330 driver
ARM: S5P64x0: Modify platform data for pl330 driver
ARM: EXYNOS: Add a alias for pdma clocks
ARM: EXYNOS: Limit usage of pl330 device instance to non-dt build
ARM: SAMSUNG: Add device tree support for pl330 dma engine wrappers
DMA: PL330: Add device tree support
ARM: EXYNOS: Modify platform data for pl330 driver
DMA: PL330: Infer transfer direction from transfer request instead of platform data
DMA: PL330: move filter function into driver
serial: samsung: Fix build for non-Exynos4210 devices
serial: samsung: add device tree support
serial: samsung: merge probe() function from all SoC specific extensions
serial: samsung: merge all SoC specific port reset functions
ARM: SAMSUNG: register uart clocks to clock lookup list
serial: samsung: remove all uses of get_clksrc and set_clksrc
...
Add of_match_table and DT style i2c registration to designware i2c
driver.
Refactored for pci/plat split by Dirk Brandewie.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Based on recent discussions, we apparently want to do bindings even for
trivial i2c devices, even though they have for years just been added. So
start a table of the currently known ones for others to be added to
over time.
(I am intentionally letting lines go over 80 characters to make it easier
to sort the file).
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Add a new EXYNOS4 compatible device tree enabled board file. Boards
based on the EXYNOS4 family of SoC's can use this as the machine/board
file. When using this machine fike, a corresponding device tree blob
which describes the board's properties should be supplied at boot time
to the kernel.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add device tree based discovery support for Samsung's rtc controller.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add device tree based discovery support for Samsung's keypad controller.
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
For PL330 dma controllers instantiated from device tree, the channel
lookup is based on phandle of the dma controller and dma request id
specified by the client node. During probe, the private data of each
channel of the controller is set to point to the device node of the
dma controller. The 'chan_id' of the each channel is used as the
dma request id.
Client driver requesting dma channels specify the phandle of the
dma controller and the request id. The pl330 filter function
converts the phandle to the device node pointer and matches that
with channel's private data. If a match is found, the request id
from the client node and the 'chan_id' of the channel is matched.
A channel is found if both the values match.
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Boojin Kim <boojin.kim@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Reviewed-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add device tree based discovery support for Samsung's uart controller.
Cc: Ben Dooks <ben-linux@fluff.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
As gpio chips get registered, a device tree node which represents the
gpio chip is searched and attached to it. A translate function is also
provided to convert the gpio specifier into actual platform settings
for pin function selection, pull up/down and driver strength settings.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
[kgene.kim@samsung.com: fixed build error]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This driver is parameterized in two ways:
a) Platform data, which supplies the set of GPIOs used by the driver.
These GPIOs can now be parsed out of device tree.
b) Machine-specific DAPM route arrays embedded into the ASoC machine
driver itself. Historically, the driver picks the appropriate array
to use using machine_is_*(). The driver now requires this array to
be parsed from device tree when instantiated through device tree,
using the core ASoC support for this parsing.
Based on work by John Bonesio, but significantly reworked since then.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We are currently using 'cavium', 'cortina' and 'st', add them to the
list of known prefixes.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
This patch adds the initial device tree for tegra30
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Adapt the driver to device tree and pass minimal platform
data from device tree needed for console boot.
No power management features will be suppported for now
since it requires more tweaks around OCP settings
to toggle forceidle/noidle/smartidle bits and handling
remote wakeup and dynamic muxing.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Allow the device tree to provide the mac address and the phy mode.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[nicolas.ferre@atmel.com: change "compatible" node property, doc and DT hwaddr]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
[jamie@jamieiles.com: add "gem" compatibility strings and doc]
Acked-by: Jamie Iles<jamie@jamieiles.com>
Acked-by: David S. Miller <davem@davemloft.net>
The Sabreauto board was renamed to Armadillo2 recently. To avoid
confusion, rename Sabreauto to Armadillo2/arm2.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add a placeholder device tree binding for the wm8994 driver. At present
the binding is essentially null as none of the platform data is supported,
and at least some of that will depend on the pending regulator bindings.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
This resolves the conflict in the
drivers/staging/iio/industrialio-core.c file due to two different
changes made to resolve the same problem.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For now they are a minimal binding. It needs to be amended with
vendor-specific settings for phy setup and link tuning, etc.
v2: Added bindings specification and phy_type properties
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Stephen Warren <swarren@nvidia.com>
Document the device tree binding for the WM8903 codec, and modify the
driver to extract platform data from the device tree, if present.
Based on work by John Bonesio, but significantly reworked since then.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver works with both, static platform data and device tree
bindings. It has been tested on a TQM855L board with two AN82527
CAN controllers on the local bus.
CC: Devicetree-discuss@lists.ozlabs.org
CC: linuxppc-dev@ozlabs.org
CC: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the XGMAC 10Gb ethernet device in the Calxeda Highbank
SOC.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device tree compiler does not recognize '-' in label name. Instead,
'_' works fine.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This adds device tree support to the nvec driver. By using this method
it is no longer necessary to specify platform data through a board
file.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Cc: Julian Andres Klode <jak@jak-linux.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adding support to generate platform data when kernel is configured
through device tree.
Also adding the binding for the TI bq20z75 fuel gadge and the
bq20z75 driver.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
This document is created for powerpc rapidio and rmu nodes in dts file.
These nodes can support two rapidio ports and message units. In addition,
It explicates the properties and gives examples about rapidio and rmu nodes.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Acked-by: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The fixed regulator driver uses of_get_fixed_voltage_config()
to extract fixed_voltage_config structure contents from device tree.
Also add documenation for additional bindings for fixed
regulators that can be passed through dt.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The helper routine is meant to be used by the regulator drivers
to extract the regulator_init_data structure from the data
that is passed from device tree.
'consumer_supplies' which is part of regulator_init_data is not extracted
as the regulator consumer mappings are passed through DT differently,
implemented in subsequent patches.
Similarly the regulator<-->parent/supply mapping is handled in
subsequent patches.
Also add documentation for regulator bindings to be used to pass
regulator_init_data struct information from device tree.
Some of the regulator properties which are linux and board specific,
are left out since its not clear if they can
be in someway embedded into the kernel or passed in from DT.
They will be revisited later.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This adds a device tree binding for the VIC based on the of_irq_init()
support. This adds an irqdomain to the vic and always registers all
vics in the static vic array rather than for pm only to keep track of
the irq domain. struct irq_data::hwirq is used where appropriate rather
than runtime masking.
v3: - include linux/export.h for THIS_MODULE
v2: - use irq_domain_simple_ops
- remove stub implementation of vic_of_init for !CONFIG_OF
- Make VIC select IRQ_DOMAIN
Reviewed-by: Rob Herring <robherring2@gmail.com>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
The GIC support code is heavily using the fact that hardware
implementations are exposing banked registers. Unfortunately, it
looks like at least one GIC implementation (EXYNOS) offers both
the distributor and the CPU interfaces at different addresses,
depending on the CPU.
This problem is solved by allowing the distributor and CPU interface
addresses to be per-cpu variables for the platforms that require it.
The EXYNOS code is updated not to mess with the GIC internals while
handling interrupts, and struct gic_chip_data is back to being private.
The DT binding for the gic is updated to allow an optional "cpu-offset"
value, which is used to compute the various base addresses.
Finally, a new config option (GIC_NON_BANKED) is used to control this
feature, so the overhead is only present on kernels compiled with
support for EXYNOS.
Tested on Origen (EXYNOS4) and Panda (OMAP4).
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add device tree probe support for atmel at_hdmac DMA driver.
Bindings are added to specify DMA controller configuration.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
* git://git.infradead.org/mtd-2.6: (226 commits)
mtd: tests: annotate as DANGEROUS in Kconfig
mtd: tests: don't use mtd0 as a default
mtd: clean up usage of MTD_DOCPROBE_ADDRESS
jffs2: add compr=lzo and compr=zlib options
jffs2: implement mount option parsing and compression overriding
mtd: nand: initialize ops.mode
mtd: provide an alias for the redboot module name
mtd: m25p80: don't probe device which has status of 'disabled'
mtd: nand_h1900 never worked
mtd: Add DiskOnChip G3 support
mtd: m25p80: add EON flash EN25Q32B into spi flash id table
mtd: mark block device queue as non-rotational
mtd: r852: make r852_pm_ops static
mtd: m25p80: add support for at25df321a spi data flash
mtd: mxc_nand: preset_v1_v2: unlock all NAND flash blocks
mtd: nand: switch `check_pattern()' to standard `memcmp()'
mtd: nand: invalidate cache on unaligned reads
mtd: nand: do not scan bad blocks with NAND_BBT_NO_OOB set
mtd: nand: wait to set BBT version
mtd: nand: scrub BBT on ECC errors
...
Fix up trivial conflicts:
- arch/arm/mach-at91/board-usb-a9260.c
Merged into board-usb-a926x.c
- drivers/mtd/maps/lantiq-flash.c
add_mtd_partitions -> mtd_device_register vs changed to use
mtd_device_parse_register.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (106 commits)
powerpc/p3060qds: Add support for P3060QDS board
powerpc/83xx: Add shutdown request support to MCU handling on MPC8349 MITX
powerpc/85xx: Make kexec to interate over online cpus
powerpc/fsl_booke: Fix comment in head_fsl_booke.S
powerpc/85xx: issue 15 EOI after core reset for FSL CoreNet devices
powerpc/8xxx: Fix interrupt handling in MPC8xxx GPIO driver
powerpc/85xx: Add 'fsl,pq3-gpio' compatiable for GPIO driver
powerpc/86xx: Correct Gianfar support for GE boards
powerpc/cpm: Clear muram before it is in use.
drivers/virt: add ioctl for 32-bit compat on 64-bit to fsl-hv-manager
powerpc/fsl_msi: add support for "msi-address-64" property
powerpc/85xx: Setup secondary cores PIR with hard SMP id
powerpc/fsl-booke: Fix settlbcam for 64-bit
powerpc/85xx: Adding DCSR node to dtsi device trees
powerpc/85xx: clean up FPGA device tree nodes for Freecsale QorIQ boards
powerpc/85xx: fix PHYS_64BIT selection for P1022DS
powerpc/fsl-booke: Fix setup_initial_memory_limit to not blindly map
powerpc: respect mem= setting for early memory limit setup
powerpc: Update corenet64_smp_defconfig
powerpc: Update mpc85xx/corenet 32-bit defconfigs
...
Fix up trivial conflicts in:
- arch/powerpc/configs/40x/hcu4_defconfig
removed stale file, edited elsewhere
- arch/powerpc/include/asm/udbg.h, arch/powerpc/kernel/udbg.c:
added opal and gelic drivers vs added ePAPR driver
- drivers/tty/serial/8250.c
moved UPIO_TSI to powerpc vs removed UPIO_DWAPB support
* git://github.com/rustyrussell/linux:
virtio-blk: use ida to allocate disk index
virtio: Add platform bus driver for memory mapped virtio device
virtio: Dont add "config" to list for !per_vq_vector
virtio: console: wait for first console port for early console output
virtio: console: add port stats for bytes received, sent and discarded
virtio: console: make discard_port_data() use get_inbuf()
virtio: console: rename variable
virtio: console: make get_inbuf() return port->inbuf if present
virtio: console: Fix return type for get_inbuf()
virtio: console: Use wait_event_freezable instead of _interruptible
virtio: console: Ignore port name update request if name already set
virtio: console: Fix indentation
virtio: modify vring_init and vring_size to take account of the layout containing *_event_idx
virtio.h: correct comment for struct virtio_driver
virtio-net: Use virtio_config_val() for retrieving config
virtio_config: Add virtio_config_val_len()
virtio-console: Use virtio_config_val() for retrieving config
* 'next/soc' of git://git.linaro.org/people/arnd/arm-soc: (21 commits)
MAINTAINERS: add ARM/FREESCALE IMX6 entry
arm/imx: merge i.MX3 and i.MX6
arm/imx6q: add suspend/resume support
arm/imx6q: add device tree machine support
arm/imx6q: add smp and cpu hotplug support
arm/imx6q: add core drivers clock, gpc, mmdc and src
arm/imx: add gic_handle_irq function
arm/imx6q: add core definitions and low-level debug uart
arm/imx6q: add device tree source
ARM: highbank: add suspend support
ARM: highbank: Add cpu hotplug support
ARM: highbank: add SMP support
MAINTAINERS: add Calxeda Highbank ARM platform
ARM: add Highbank core platform support
ARM: highbank: add devicetree source
ARM: l2x0: add empty l2x0_of_init
picoxcell: add a definition of VMALLOC_END
picoxcell: remove custom ioremap implementation
picoxcell: add the DTS for the PC7302 board
picoxcell: add the DTS for pc3x2 and pc3x3 devices
...
Fix up trivial conflicts in arch/arm/Kconfig, and some more header file
conflicts in arch/arm/mach-omap2/board-generic.c (as per an ealier merge
by Arnd).
* 'next/dt' of git://git.linaro.org/people/arnd/arm-soc:
ARM: gic: use module.h instead of export.h
ARM: gic: fix irq_alloc_descs handling for sparse irq
ARM: gic: add OF based initialization
ARM: gic: add irq_domain support
irq: support domains with non-zero hwirq base
of/irq: introduce of_irq_init
ARM: at91: add at91sam9g20 and Calao USB A9G20 DT support
ARM: at91: dt: at91sam9g45 family and board device tree files
arm/mx5: add device tree support for imx51 babbage
arm/mx5: add device tree support for imx53 boards
ARM: msm: Add devicetree support for msm8660-surf
msm_serial: Add devicetree support
msm_serial: Use relative resources for iomem
Fix up conflicts in arch/arm/mach-at91/{at91sam9260.c,at91sam9g45.c}
* 'next/cleanup2' of git://git.linaro.org/people/arnd/arm-soc: (31 commits)
ARM: OMAP: Warn if omap_ioremap is called before SoC detection
ARM: OMAP: Move set_globals initialization to happen in init_early
ARM: OMAP: Map SRAM later on with ioremap_exec()
ARM: OMAP: Remove calls to SRAM allocations for framebuffer
ARM: OMAP: Avoid cpu_is_omapxxxx usage until map_io is done
ARM: OMAP1: Use generic map_io, init_early and init_irq
arm/dts: OMAP3+: Add mpu, dsp and iva nodes
arm/dts: OMAP4: Add a main ocp entry bound to l3-noc driver
ARM: OMAP2+: l3-noc: Add support for device-tree
ARM: OMAP2+: board-generic: Add i2c static init
ARM: OMAP2+: board-generic: Add DT support to generic board
arm/dts: Add support for OMAP3 Beagle board
arm/dts: Add initial device tree support for OMAP3 SoC
arm/dts: Add support for OMAP4 SDP board
arm/dts: Add support for OMAP4 PandaBoard
arm/dts: Add initial device tree support for OMAP4 SoC
ARM: OMAP: omap_device: Add a method to build an omap_device from a DT node
ARM: OMAP: omap_device: Add omap_device_[alloc|delete] for DT integration
of: Add helpers to get one string in multiple strings property
ARM: OMAP2+: devices: Remove all omap_device_pm_latency structures
...
Fix up trivial header file conflicts in arch/arm/mach-omap2/board-generic.c
