OpenFirmware wasn't quite following the protocol described in boot.txt
and the kernel has detected this through use of the sentinel value
in boot_params. OFW does zero out almost all of the stuff that it should
do, but not the sentinel.
This causes the kernel to clear olpc_ofw_header, which breaks x86 OLPC
support.
OpenFirmware has now been fixed. However, it would be nice if we could
maintain Linux compatibility with old firmware versions. To do that, we just
have to avoid zeroing out olpc_ofw_header.
OFW does not write to any other parts of the header that are being zapped
by the sentinel-detection code, and all users of olpc_ofw_header are
somewhat protected through checking for the OLPC_OFW_SIG magic value
before using it. So this should not cause any problems for anyone.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/20130809221420.618E6FAB03@dev.laptop.org
Acked-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org> # v3.9+
This is based on a patch that Zhenzhong Duan had sent - which
was missing some of the remaining pieces. The kernel has the
logic to handle Xen-type-exceptions using the paravirt interface
in the assembler code (see PARAVIRT_ADJUST_EXCEPTION_FRAME -
pv_irq_ops.adjust_exception_frame and and INTERRUPT_RETURN -
pv_cpu_ops.iret).
That means the nmi handler (and other exception handlers) use
the hypervisor iret.
The other changes that would be neccessary for this would
be to translate the NMI_VECTOR to one of the entries on the
ipi_vector and make xen_send_IPI_mask_allbutself use different
events.
Fortunately for us commit 1db01b4903
(xen: Clean up apic ipi interface) implemented this and we piggyback
on the cleanup such that the apic IPI interface will pass the right
vector value for NMI.
With this patch we can trigger NMIs within a PV guest (only tested
x86_64).
For this to work with normal PV guests (not initial domain)
we need the domain to be able to use the APIC ops - they are
already implemented to use the Xen event channels. For that
to be turned on in a PV domU we need to remove the masking
of X86_FEATURE_APIC.
Incidentally that means kgdb will also now work within
a PV guest without using the 'nokgdbroundup' workaround.
Note that the 32-bit version is different and this patch
does not enable that.
CC: Lisa Nguyen <lisa@xenapiadmin.com>
CC: Ben Guthro <benjamin.guthro@citrix.com>
CC: Zhenzhong Duan <zhenzhong.duan@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
[v1: Fixed up per David Vrabel comments]
Reviewed-by: Ben Guthro <benjamin.guthro@citrix.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
These are needed by both guest and host.
Originally-from: Srivatsa Vaddagiri <vatsa@linux.vnet.ibm.com>
Signed-off-by: Raghavendra K T <raghavendra.kt@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/1376058122-8248-13-git-send-email-raghavendra.kt@linux.vnet.ibm.com
Acked-by: Gleb Natapov <gleb@redhat.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Maintain a flag in the LSB of the ticket lock tail which indicates
whether anyone is in the lock slowpath and may need kicking when
the current holder unlocks. The flags are set when the first locker
enters the slowpath, and cleared when unlocking to an empty queue (ie,
no contention).
In the specific implementation of lock_spinning(), make sure to set
the slowpath flags on the lock just before blocking. We must do
this before the last-chance pickup test to prevent a deadlock
with the unlocker:
Unlocker Locker
test for lock pickup
-> fail
unlock
test slowpath
-> false
set slowpath flags
block
Whereas this works in any ordering:
Unlocker Locker
set slowpath flags
test for lock pickup
-> fail
block
unlock
test slowpath
-> true, kick
If the unlocker finds that the lock has the slowpath flag set but it is
actually uncontended (ie, head == tail, so nobody is waiting), then it
clears the slowpath flag.
The unlock code uses a locked add to update the head counter. This also
acts as a full memory barrier so that its safe to subsequently
read back the slowflag state, knowing that the updated lock is visible
to the other CPUs. If it were an unlocked add, then the flag read may
just be forwarded from the store buffer before it was visible to the other
CPUs, which could result in a deadlock.
Unfortunately this means we need to do a locked instruction when
unlocking with PV ticketlocks. However, if PV ticketlocks are not
enabled, then the old non-locked "add" is the only unlocking code.
Note: this code relies on gcc making sure that unlikely() code is out of
line of the fastpath, which only happens when OPTIMIZE_SIZE=n. If it
doesn't the generated code isn't too bad, but its definitely suboptimal.
Thanks to Srivatsa Vaddagiri for providing a bugfix to the original
version of this change, which has been folded in.
Thanks to Stephan Diestelhorst for commenting on some code which relied
on an inaccurate reading of the x86 memory ordering rules.
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Link: http://lkml.kernel.org/r/1376058122-8248-11-git-send-email-raghavendra.kt@linux.vnet.ibm.com
Signed-off-by: Srivatsa Vaddagiri <vatsa@linux.vnet.ibm.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Stephan Diestelhorst <stephan.diestelhorst@amd.com>
Signed-off-by: Raghavendra K T <raghavendra.kt@linux.vnet.ibm.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Increment ticket head/tails by 2 rather than 1 to leave the LSB free
to store a "is in slowpath state" bit. This halves the number
of possible CPUs for a given ticket size, but this shouldn't matter
in practice - kernels built for 32k+ CPU systems are probably
specially built for the hardware rather than a generic distro
kernel.
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Link: http://lkml.kernel.org/r/1376058122-8248-9-git-send-email-raghavendra.kt@linux.vnet.ibm.com
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Attilio Rao <attilio.rao@citrix.com>
Signed-off-by: Raghavendra K T <raghavendra.kt@linux.vnet.ibm.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Although the lock_spinning calls in the spinlock code are on the
uncommon path, their presence can cause the compiler to generate many
more register save/restores in the function pre/postamble, which is in
the fast path. To avoid this, convert it to using the pvops callee-save
calling convention, which defers all the save/restores until the actual
function is called, keeping the fastpath clean.
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Link: http://lkml.kernel.org/r/1376058122-8248-8-git-send-email-raghavendra.kt@linux.vnet.ibm.com
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Attilio Rao <attilio.rao@citrix.com>
Signed-off-by: Raghavendra K T <raghavendra.kt@linux.vnet.ibm.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Now that the paravirtualization layer doesn't exist at the spinlock
level any more, we can collapse the __ticket_ functions into the arch_
functions.
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Link: http://lkml.kernel.org/r/1376058122-8248-4-git-send-email-raghavendra.kt@linux.vnet.ibm.com
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Attilio Rao <attilio.rao@citrix.com>
Signed-off-by: Raghavendra K T <raghavendra.kt@linux.vnet.ibm.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Rather than outright replacing the entire spinlock implementation in
order to paravirtualize it, keep the ticket lock implementation but add
a couple of pvops hooks on the slow patch (long spin on lock, unlocking
a contended lock).
Ticket locks have a number of nice properties, but they also have some
surprising behaviours in virtual environments. They enforce a strict
FIFO ordering on cpus trying to take a lock; however, if the hypervisor
scheduler does not schedule the cpus in the correct order, the system can
waste a huge amount of time spinning until the next cpu can take the lock.
(See Thomas Friebel's talk "Prevent Guests from Spinning Around"
http://www.xen.org/files/xensummitboston08/LHP.pdf for more details.)
To address this, we add two hooks:
- __ticket_spin_lock which is called after the cpu has been
spinning on the lock for a significant number of iterations but has
failed to take the lock (presumably because the cpu holding the lock
has been descheduled). The lock_spinning pvop is expected to block
the cpu until it has been kicked by the current lock holder.
- __ticket_spin_unlock, which on releasing a contended lock
(there are more cpus with tail tickets), it looks to see if the next
cpu is blocked and wakes it if so.
When compiled with CONFIG_PARAVIRT_SPINLOCKS disabled, a set of stub
functions causes all the extra code to go away.
Results:
=======
setup: 32 core machine with 32 vcpu KVM guest (HT off) with 8GB RAM
base = 3.11-rc
patched = base + pvspinlock V12
+-----------------+----------------+--------+
dbench (Throughput in MB/sec. Higher is better)
+-----------------+----------------+--------+
| base (stdev %)|patched(stdev%) | %gain |
+-----------------+----------------+--------+
| 15035.3 (0.3) |15150.0 (0.6) | 0.8 |
| 1470.0 (2.2) | 1713.7 (1.9) | 16.6 |
| 848.6 (4.3) | 967.8 (4.3) | 14.0 |
| 652.9 (3.5) | 685.3 (3.7) | 5.0 |
+-----------------+----------------+--------+
pvspinlock shows benefits for overcommit ratio > 1 for PLE enabled cases,
and undercommits results are flat
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Link: http://lkml.kernel.org/r/1376058122-8248-2-git-send-email-raghavendra.kt@linux.vnet.ibm.com
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Attilio Rao <attilio.rao@citrix.com>
[ Raghavendra: Changed SPIN_THRESHOLD, fixed redefinition of arch_spinlock_t]
Signed-off-by: Raghavendra K T <raghavendra.kt@linux.vnet.ibm.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Moves the relocation handling into C, after decompression. This requires
that the decompressed size is passed to the decompression routine as
well so that relocations can be found. Only kernels that need relocation
support will use the code (currently just x86_32), but this is laying
the ground work for 64-bit using it in support of KASLR.
Based on work by Neill Clift and Michael Davidson.
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: http://lkml.kernel.org/r/20130708161517.GA4832@www.outflux.net
Acked-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
If we let L1 use EPT, we should probably also support the INVEPT instruction.
In our current nested EPT implementation, when L1 changes its EPT table
for L2 (i.e., EPT12), L0 modifies the shadow EPT table (EPT02), and in
the course of this modification already calls INVEPT. But if last level
of shadow page is unsync not all L1's changes to EPT12 are intercepted,
which means roots need to be synced when L1 calls INVEPT. Global INVEPT
should not be different since roots are synced by kvm_mmu_load() each
time EPTP02 changes.
Reviewed-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Nadav Har'El <nyh@il.ibm.com>
Signed-off-by: Jun Nakajima <jun.nakajima@intel.com>
Signed-off-by: Xinhao Xu <xinhao.xu@intel.com>
Signed-off-by: Yang Zhang <yang.z.zhang@Intel.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Inject nEPT fault to L1 guest. This patch is original from Xinhao.
Reviewed-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Jun Nakajima <jun.nakajima@intel.com>
Signed-off-by: Xinhao Xu <xinhao.xu@intel.com>
Signed-off-by: Yang Zhang <yang.z.zhang@Intel.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As specified by H. Peter Anvin, the best nops for x86 without knowing
the running computer is:
32bit:
0x3e, 0x8d, 0x74, 0x26, 0x00 also known as GENERIC_NOP5_ATOMIC
64bit:
0x0f, 0x1f, 0x44, 0x00, 0x00 also known as P6_NOP5_ATOMIC
Currently the default nop that is used by jump label is:
0xe9 0x00 0x00 0x00 0x00
Which is really a 5byte jump to the next position.
It's better to use a real nop than a jmp.
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Jason Baron <jbaron@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
- Make all the external assembler template symbols __visible
- Move the templates inline assembler code into a top level
assembler statement, not inside a function. This avoids it being
optimized away or cloned.
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Link: http://lkml.kernel.org/r/1375740170-7446-8-git-send-email-andi@firstfloor.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
FWIW I suspect sys_rt_sigreturn/sys_sigreturn should use
standard SYSCALL wrappers. But I didn't do that change in this
patch.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Link: http://lkml.kernel.org/r/1375740170-7446-7-git-send-email-andi@firstfloor.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
These handlers are all referenced from assembler stubs, so need
to be visible.
The handlers without arguments become asmlinkage, the others __visible
to not force regparms(0) on x86-32.
I put it all into a single patch, please let me know if you want
it it split up.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Link: http://lkml.kernel.org/r/1375740170-7446-4-git-send-email-andi@firstfloor.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Mark 32bit dotraplinkage functions as __visible for LTO.
64bit already is using asmlinkage which includes it.
v2: Clean up (M.Marek)
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Link: http://lkml.kernel.org/r/1375740170-7446-3-git-send-email-andi@firstfloor.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Make the sys_call_table type defined in asm/syscall.h match
the definition in syscall_64.c
v2: include asm/syscall.h in syscall_64.c too. I left uml alone
because it doesn't have an syscall.h on its own and including
the native one leads to other errors.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Link: http://lkml.kernel.org/r/1375740170-7446-2-git-send-email-andi@firstfloor.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Richard Weinberger <richard@nod.at>
The 0x1000 bit of the MCACOD field of machine check MCi_STATUS
registers is only defined for corrected errors (where it means
that hardware may be filtering errors see SDM section 15.9.2.1).
For uncorrected errors it may, or may not be set - so we should mask
it out when checking for the architecturaly defined recoverable
error signatures (see SDM 15.9.3.1 and 15.9.3.2)
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
We try to handle the hypervisor compatibility mode by detecting hypervisor
through a specific order. This is not robust, since hypervisors may implement
each others features.
This patch tries to handle this situation by always choosing the last one in the
CPUID leaves. This is done by letting .detect() return a priority instead of
true/false and just re-using the CPUID leaf where the signature were found as
the priority (or 1 if it was found by DMI). Then we can just pick hypervisor who
has the highest priority. Other sophisticated detection method could also be
implemented on top.
Suggested by H. Peter Anvin and Paolo Bonzini.
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Doug Covelli <dcovelli@vmware.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Dan Hecht <dhecht@vmware.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Link: http://lkml.kernel.org/r/1374742475-2485-4-git-send-email-jasowang@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Switch to use hypervisor_cpuid_base() to detect KVM.
Cc: Gleb Natapov <gleb@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Link: http://lkml.kernel.org/r/1374742475-2485-3-git-send-email-jasowang@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Switch to use hypervisor_cpuid_base() to detect Xen.
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Link: http://lkml.kernel.org/r/1374742475-2485-2-git-send-email-jasowang@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This patch introduce hypervisor_cpuid_base() which loop test the hypervisor
existence function until the signature match and check the number of leaves if
required. This could be used by Xen/KVM guest to detect the existence of
hypervisor.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Link: http://lkml.kernel.org/r/1374742475-2485-1-git-send-email-jasowang@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The EFI FB quirks from efifb.c are useful for simple-framebuffer devices
as well. Apply them by default so we can convert efifb.c to use
efi-framebuffer platform devices.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Link: http://lkml.kernel.org/r/1375445127-15480-5-git-send-email-dh.herrmann@gmail.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The current situation regarding boot-framebuffers (VGA, VESA/VBE, EFI) on
x86 causes troubles when loading multiple fbdev drivers. The global
"struct screen_info" does not provide any state-tracking about which
drivers use the FBs. request_mem_region() theoretically works, but
unfortunately vesafb/efifb ignore it due to quirks for broken boards.
Avoid this by creating a platform framebuffer devices with a pointer
to the "struct screen_info" as platform-data. Drivers can now create
platform-drivers and the driver-core will refuse multiple drivers being
active simultaneously.
We keep the screen_info available for backwards-compatibility. Drivers
can be converted in follow-up patches.
Different devices are created for VGA/VESA/EFI FBs to allow multiple
drivers to be loaded on distro kernels. We create:
- "vesa-framebuffer" for VBE/VESA graphics FBs
- "efi-framebuffer" for EFI FBs
- "platform-framebuffer" for everything else
This allows to load vesafb, efifb and others simultaneously and each
picks up only the supported FB types.
Apart from platform-framebuffer devices, this also introduces a
compatibility option for "simple-framebuffer" drivers which recently got
introduced for OF based systems. If CONFIG_X86_SYSFB is selected, we
try to match the screen_info against a simple-framebuffer supported
format. If we succeed, we create a "simple-framebuffer" device instead
of a platform-framebuffer.
This allows to reuse the simplefb.c driver across architectures and also
to introduce a SimpleDRM driver. There is no need to have vesafb.c,
efifb.c, simplefb.c and more just to have architecture specific quirks
in their setup-routines.
Instead, we now move the architecture specific quirks into x86-setup and
provide a generic simple-framebuffer. For backwards-compatibility (if
strange formats are used), we still allow vesafb/efifb to be loaded
simultaneously and pick up all remaining devices.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Link: http://lkml.kernel.org/r/1375445127-15480-4-git-send-email-dh.herrmann@gmail.com
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Dick Fowles, Don Zickus and Joe Mario have been working on
improvements to perf, and noticed heavy cache line contention
on the mm_cpumask, running linpack on a 60 core / 120 thread
system.
The cause turned out to be unnecessary atomic accesses to the
mm_cpumask. When in lazy TLB mode, the CPU is only removed from
the mm_cpumask if there is a TLB flush event.
Most of the time, no such TLB flush happens, and the kernel
skips the TLB reload. It can also skip the atomic memory
set & test.
Here is a summary of Joe's test results:
* The __schedule function dropped from 24% of all program cycles down
to 5.5%.
* The cacheline contention/hotness for accesses to that bitmask went
from being the 1st/2nd hottest - down to the 84th hottest (0.3% of
all shared misses which is now quite cold)
* The average load latency for the bit-test-n-set instruction in
__schedule dropped from 10k-15k cycles down to an average of 600 cycles.
* The linpack program results improved from 133 GFlops to 144 GFlops.
Peak GFlops rose from 133 to 153.
Reported-by: Don Zickus <dzickus@redhat.com>
Reported-by: Joe Mario <jmario@redhat.com>
Tested-by: Joe Mario <jmario@redhat.com>
Signed-off-by: Rik van Riel <riel@redhat.com>
Reviewed-by: Paul Turner <pjt@google.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20130731221421.616d3d20@annuminas.surriel.com
[ Made the comments consistent around the modified code. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The target frequency calculation method in the ondemand governor has
changed and it is now independent of the measured average frequency.
Consequently, the APERF/MPERF support in cpufreq is not used any
more, so drop it.
[rjw: Changelog]
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
For modern CPUs, perf clock is directly related to TSC. TSC
can be calculated from perf clock and vice versa using a simple
calculation. Two of the three componenets of that calculation
are already exported in struct perf_event_mmap_page. This patch
exports the third.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Link: http://lkml.kernel.org/r/1372425741-1676-3-git-send-email-adrian.hunter@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In fd4363fff3 ("x86: Introduce int3 (breakpoint)-based
instruction patching"), the mechanism that was introduced for
notifying alternatives code from int3 exception handler that and
exception occured was die_notifier.
This is however problematic, as early code might be using jump
labels even before the notifier registration has been performed,
which will then lead to an oops due to unhandled exception. One
of such occurences has been encountered by Fengguang:
int3: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
Modules linked in:
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.11.0-rc1-01429-g04bf576 #8
task: ffff88000da1b040 ti: ffff88000da1c000 task.ti: ffff88000da1c000
RIP: 0010:[<ffffffff811098cc>] [<ffffffff811098cc>] ttwu_do_wakeup+0x28/0x225
RSP: 0000:ffff88000dd03f10 EFLAGS: 00000006
RAX: 0000000000000000 RBX: ffff88000dd12940 RCX: ffffffff81769c40
RDX: 0000000000000002 RSI: 0000000000000000 RDI: 0000000000000001
RBP: ffff88000dd03f28 R08: ffffffff8176a8c0 R09: 0000000000000002
R10: ffffffff810ff484 R11: ffff88000dd129e8 R12: ffff88000dbc90c0
R13: ffff88000dbc90c0 R14: ffff88000da1dfd8 R15: ffff88000da1dfd8
FS: 0000000000000000(0000) GS:ffff88000dd00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 00000000ffffffff CR3: 0000000001c88000 CR4: 00000000000006e0
Stack:
ffff88000dd12940 ffff88000dbc90c0 ffff88000da1dfd8 ffff88000dd03f48
ffffffff81109e2b ffff88000dd12940 0000000000000000 ffff88000dd03f68
ffffffff81109e9e 0000000000000000 0000000000012940 ffff88000dd03f98
Call Trace:
<IRQ>
[<ffffffff81109e2b>] ttwu_do_activate.constprop.56+0x6d/0x79
[<ffffffff81109e9e>] sched_ttwu_pending+0x67/0x84
[<ffffffff8110c845>] scheduler_ipi+0x15a/0x2b0
[<ffffffff8104dfb4>] smp_reschedule_interrupt+0x38/0x41
[<ffffffff8173bf5d>] reschedule_interrupt+0x6d/0x80
<EOI>
[<ffffffff810ff484>] ? __atomic_notifier_call_chain+0x5/0xc1
[<ffffffff8105cc30>] ? native_safe_halt+0xd/0x16
[<ffffffff81015f10>] default_idle+0x147/0x282
[<ffffffff81017026>] arch_cpu_idle+0x3d/0x5d
[<ffffffff81127d6a>] cpu_idle_loop+0x46d/0x5db
[<ffffffff81127f5c>] cpu_startup_entry+0x84/0x84
[<ffffffff8104f4f8>] start_secondary+0x3c8/0x3d5
[...]
Fix this by directly calling poke_int3_handler() from the int3
exception handler (analogically to what ftrace has been doing
already), instead of relying on notifier, registration of which
might not have yet been finalized by the time of the first trap.
Reported-and-tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/alpine.LNX.2.00.1307231007490.14024@pobox.suse.cz
Signed-off-by: Ingo Molnar <mingo@kernel.org>
[KVM maintainers:
The underlying support for this is in perf/core now. So please merge
this patch into the KVM tree.]
This is not arch perfmon, but older CPUs will just ignore it. This makes
it possible to do at least some TSX measurements from a KVM guest
v2: Various fixes to address review feedback
v3: Ignore the bits when no CPUID. No #GP. Force raw events with TSX bits.
v4: Use reserved bits for #GP
v5: Remove obsolete argument
Acked-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since introducing the text_poke_bp() for all text_poke_smp*()
callers, text_poke_smp*() are now unused. This patch basically
reverts:
3d55cc8a05 ("x86: Add text_poke_smp for SMP cross modifying code")
7deb18dcf0 ("x86: Introduce text_poke_smp_batch() for batch-code modifying")
and related commits.
This patch also fixes a Kconfig dependency issue on STOP_MACHINE
in the case of CONFIG_SMP && !CONFIG_MODULE_UNLOAD.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Reviewed-by: Jiri Kosina <jkosina@suse.cz>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Jason Baron <jbaron@akamai.com>
Cc: yrl.pp-manager.tt@hitachi.com
Cc: Borislav Petkov <bpetkov@suse.de>
Link: http://lkml.kernel.org/r/20130718114753.26675.18714.stgit@mhiramat-M0-7522
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Linux as a guest on KVM hypervisor, the only user of the pvclock
vsyscall interface, does not require notification on task migration
because:
1. cpu ID number maps 1:1 to per-CPU pvclock time info.
2. per-CPU pvclock time info is updated if the
underlying CPU changes.
3. that version is increased whenever underlying CPU
changes.
Which is sufficient to guarantee nanoseconds counter
is calculated properly.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Introduce a method for run-time instruction patching on a live SMP kernel
based on int3 breakpoint, completely avoiding the need for stop_machine().
The way this is achieved:
- add a int3 trap to the address that will be patched
- sync cores
- update all but the first byte of the patched range
- sync cores
- replace the first byte (int3) by the first byte of
replacing opcode
- sync cores
According to
http://lkml.indiana.edu/hypermail/linux/kernel/1001.1/01530.html
synchronization after replacing "all but first" instructions should not
be necessary (on Intel hardware), as the syncing after the subsequent
patching of the first byte provides enough safety.
But there's not only Intel HW out there, and we'd rather be on a safe
side.
If any CPU instruction execution would collide with the patching,
it'd be trapped by the int3 breakpoint and redirected to the provided
"handler" (which would typically mean just skipping over the patched
region, acting as "nop" has been there, in case we are doing nop -> jump
and jump -> nop transitions).
Ftrace has been using this very technique since 08d636b ("ftrace/x86:
Have arch x86_64 use breakpoints instead of stop machine") for ages
already, and jump labels are another obvious potential user of this.
Based on activities of Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
a few years ago.
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Link: http://lkml.kernel.org/r/alpine.LNX.2.00.1307121102440.29788@pobox.suse.cz
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Change the bitops operation to be naturally "long", i.e. 63 bits on
the 64-bit kernel. Additional bugs are likely to crop up in the
future.
We already have bugs which machines with > 16 TiB of memory in a
single node, as can happen if memory is interleaved. The x86 bitop
operations take a signed index, so using an unsigned type is not an
option.
Jim Kukunas measured the effect of this patch on kernel size: it adds
2779 bytes to the allyesconfig kernel. Some of that probably could be
elided by replacing the inline functions with macros which select the
32-bit type if the index is a 32-bit value, something like:
In that case we could also use "Jr" constraints for the 64-bit
version.
However, this would more than double the amount of code for a
relatively small gain.
Note that we can't use ilog2() for _BITOPS_LONG_SHIFT, as that causes
a recursive header inclusion problem.
The change to constant_test_bit() should both generate better code and
give correct result for negative bit indicies. As previously written
the compiler had to generate extra code to create the proper wrong
result for negative values.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Jim Kukunas <james.t.kukunas@intel.com>
Link: http://lkml.kernel.org/n/tip-z61ofiwe90xeyb461o72h8ya@git.kernel.org
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
are flagged as __cpuinit -- so if we remove the __cpuinit from
arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
content into no-ops as early as possible, since that will get rid
of these warnings. In any case, they are temporary and harmless.
This removes all the arch/x86 uses of the __cpuinit macros from
all C files. x86 only had the one __CPUINIT used in assembly files,
and it wasn't paired off with a .previous or a __FINIT, so we can
delete it directly w/o any corresponding additional change there.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Pull thermal management updates from Zhang Rui:
"There are not too many changes this time, except two new platform
thermal drivers, ti-soc-thermal driver and x86_pkg_temp_thermal
driver, and a couple of small fixes.
Highlights:
- move the ti-soc-thermal driver out of the staging tree to the
thermal tree.
- introduce the x86_pkg_temp_thermal driver. This driver registers
CPU digital temperature package level sensor as a thermal zone.
- small fixes/cleanups including removing redundant use of
platform_set_drvdata() and of_match_ptr for all platform thermal
drivers"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (34 commits)
thermal: cpu_cooling: fix stub function
thermal: ti-soc-thermal: use standard GPIO DT bindings
thermal: MAINTAINERS: Add git tree path for SoC specific updates
thermal: fix x86_pkg_temp_thermal.c build and Kconfig
Thermal: Documentation for x86 package temperature thermal driver
Thermal: CPU Package temperature thermal
thermal: consider emul_temperature while computing trend
thermal: ti-soc-thermal: add DT example for DRA752 chip
thermal: ti-soc-thermal: add dra752 chip to device table
thermal: ti-soc-thermal: add thermal data for DRA752 chips
thermal: ti-soc-thermal: remove usage of IS_ERR_OR_NULL
thermal: ti-soc-thermal: freeze FSM while computing trend
thermal: ti-soc-thermal: remove external heat while extrapolating hotspot
thermal: ti-soc-thermal: update DT reference for OMAP5430
x86, mcheck, therm_throt: Process package thresholds
thermal: cpu_cooling: fix 'descend' check in get_property()
Thermal: spear: Remove redundant use of of_match_ptr
Thermal: kirkwood: Remove redundant use of of_match_ptr
Thermal: dove: Remove redundant use of of_match_ptr
Thermal: armada: Remove redundant use of of_match_ptr
...
Pull drm updates from Dave Airlie:
"Okay this is the big one, I was stalled on the fbdev pull req as I
stupidly let fbdev guys merge a patch I required to fix a warning with
some patches I had, they ended up merging the patch from the wrong
place, but the warning should be fixed. In future I'll just take the
patch myself!
Outside drm:
There are some snd changes for the HDMI audio interactions on haswell,
they've been acked for inclusion via my tree. This relies on the
wound/wait tree from Ingo which is already merged.
Major changes:
AMD finally released the dynamic power management code for all their
GPUs from r600->present day, this is great, off by default for now but
also a huge amount of code, in fact it is most of this pull request.
Since it landed there has been a lot of community testing and Alex has
sent a lot of fixes for any bugs found so far. I suspect radeon might
now be the biggest kernel driver ever :-P p.s. radeon.dpm=1 to enable
dynamic powermanagement for anyone.
New drivers:
Renesas r-car display unit.
Other highlights:
- core: GEM CMA prime support, use new w/w mutexs for TTM
reservations, cursor hotspot, doc updates
- dvo chips: chrontel 7010B support
- i915: Haswell (fbc, ips, vecs, watermarks, audio powerwell),
Valleyview (enabled by default, rc6), lots of pll reworking, 30bpp
support (this time for sure)
- nouveau: async buffer object deletion, context/register init
updates, kernel vp2 engine support, GF117 support, GK110 accel
support (with external nvidia ucode), context cleanups.
- exynos: memory leak fixes, Add S3C64XX SoC series support, device
tree updates, common clock framework support,
- qxl: cursor hotspot support, multi-monitor support, suspend/resume
support
- mgag200: hw cursor support, g200 mode limiting
- shmobile: prime support
- tegra: fixes mostly
I've been banging on this quite a lot due to the size of it, and it
seems to okay on everything I've tested it on."
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (811 commits)
drm/radeon/dpm: implement vblank_too_short callback for si
drm/radeon/dpm: implement vblank_too_short callback for cayman
drm/radeon/dpm: implement vblank_too_short callback for btc
drm/radeon/dpm: implement vblank_too_short callback for evergreen
drm/radeon/dpm: implement vblank_too_short callback for 7xx
drm/radeon/dpm: add checks against vblank time
drm/radeon/dpm: add helper to calculate vblank time
drm/radeon: remove stray line in old pm code
drm/radeon/dpm: fix display_gap programming on rv7xx
drm/nvc0/gr: fix gpc firmware regression
drm/nouveau: fix minor thinko causing bo moves to not be async on kepler
drm/radeon/dpm: implement force performance level for TN
drm/radeon/dpm: implement force performance level for ON/LN
drm/radeon/dpm: implement force performance level for SI
drm/radeon/dpm: implement force performance level for cayman
drm/radeon/dpm: implement force performance levels for 7xx/eg/btc
drm/radeon/dpm: add infrastructure to force performance levels
drm/radeon: fix surface setup on r1xx
drm/radeon: add support for 3d perf states on older asics
drm/radeon: set default clocks for SI when DPM is disabled
...
Merge together the unicore32, arm, and x86 reboot= command line
parameter handling.
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a boot option to disable firmware first mode for corrected errors.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The Corrected Machine Check structure (CMC) in HEST has a flag which can be
set by the firmware to indicate to the OS that it prefers to process the
corrected error events first. In this scenario, the OS is expected to not
monitor for corrected errors (through CMCI/polling). Instead, the firmware
notifies the OS on corrected error events through GHES.
Linux already has support for GHES. This patch adds support for parsing CMC
structure and to disable CMCI/polling if the firmware first flag is set.
Further, the list of machine check bank structures at the end of CMC is used
to determine which MCA banks function in FF mode, so that we continue to
monitor error events on the other banks.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Pull timer core updates from Thomas Gleixner:
"The timer changes contain:
- posix timer code consolidation and fixes for odd corner cases
- sched_clock implementation moved from ARM to core code to avoid
duplication by other architectures
- alarm timer updates
- clocksource and clockevents unregistration facilities
- clocksource/events support for new hardware
- precise nanoseconds RTC readout (Xen feature)
- generic support for Xen suspend/resume oddities
- the usual lot of fixes and cleanups all over the place
The parts which touch other areas (ARM/XEN) have been coordinated with
the relevant maintainers. Though this results in an handful of
trivial to solve merge conflicts, which we preferred over nasty cross
tree merge dependencies.
The patches which have been committed in the last few days are bug
fixes plus the posix timer lot. The latter was in akpms queue and
next for quite some time; they just got forgotten and Frederic
collected them last minute."
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (59 commits)
hrtimer: Remove unused variable
hrtimers: Move SMP function call to thread context
clocksource: Reselect clocksource when watchdog validated high-res capability
posix-cpu-timers: don't account cpu timer after stopped thread runtime accounting
posix_timers: fix racy timer delta caching on task exit
posix-timers: correctly get dying task time sample in posix_cpu_timer_schedule()
selftests: add basic posix timers selftests
posix_cpu_timers: consolidate expired timers check
posix_cpu_timers: consolidate timer list cleanups
posix_cpu_timer: consolidate expiry time type
tick: Sanitize broadcast control logic
tick: Prevent uncontrolled switch to oneshot mode
tick: Make oneshot broadcast robust vs. CPU offlining
x86: xen: Sync the CMOS RTC as well as the Xen wallclock
x86: xen: Sync the wallclock when the system time is set
timekeeping: Indicate that clock was set in the pvclock gtod notifier
timekeeping: Pass flags instead of multiple bools to timekeeping_update()
xen: Remove clock_was_set() call in the resume path
hrtimers: Support resuming with two or more CPUs online (but stopped)
timer: Fix jiffies wrap behavior of round_jiffies_common()
...
