This patch enables all multicast packets in non suspend mode
and enable multicast filtering in wow suspend mode. This also
fixes a bug in multicast where the driver assumed disable
multicast-all command disabled/filtered all multicast
packets, which was wrong assumption, because firmware will
apply the programmed filter.
Multicast requirements
- Enable forward all multicast packets(no filtering) in
non suspend mode.
- Enable multicast filtering in wow suspend mode for both
AP and CLIENT.
kvalo: fix a checkpatch warning and drop unrelated newline removal
Signed-off-by: Naveen Gangadharan <ngangadh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The patch "ath6kl: support fw reporting phy capabilities" gave the
firmware the ability to disable certain wiphy supported bands. Check if
this is the case in ath6kl_wmi_beginscan_cmd to avoid dereferencing a
NULL pointer.
kvalo: change the patch so that there's no code between declarations
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Do not assume anyone before us includes it for us.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* PS_WAIT_FOR_TX_ACK is used in network-sleep mode and checking
it for handling IDLE transitions is incorrect. Fix this.
* RX PCU/DMA engines have to be stopped before setting the chip into
full-sleep mode - otherwise the chip becomes mute.
* Make things a bit clear by checking explicitly for network-sleep
mode in the tx() routine and add a couple of debug statements
to aid PS debugging.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix merge between commit 3adadc08cc ("net ax25: Reorder ax25_exit to
remove races") and commit 0ca7a4c87d ("net ax25: Simplify and
cleanup the ax25 sysctl handling")
The former moved around the sysctl register/unregister calls, the
later simply removed them.
With help from Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend debugfs entry for dfs_stats with DFS detection events
and shared pool statistics.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix the following bug: in tkip mode, qos-null ps on/off packets
are dropped due to incorrect packet length so that ath9k softap
can't handle powersave state transition of peer STA correctly.
Signed-off-by: Michael Liang <mliang@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It does not work properly and reduces throughput.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The delay calculation is the same for all chips, however some parts of the
code missed the extra delay factor for half/quarter.
Clean up the code and move the delay calculation to a common place.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For some reason the MAC timing is a bit off when waiting for ACKs, so add
some extra delay to the ACK timeout values. Significantly reduces the
number of retransmissions in my tests.
Also disable the 2.4 GHz ACK timeout workaround in half/quarter mode, it
is not required there.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9462 uses modified version of 3-Wire hw scheme for btcoex.
MCI itself is not a separate hw scheme but it aids to manage
multiple bt profiles. In ar9462, bt priority traffic is identified
by the number of bt profile types instead of gpio. So that this
patch removes MCI hw scheme.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As of now beacon configuration is being called multiple times
in bss info change notification. This patch avoids multiple
configuration and make it simpler.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds locking of the detector's shared pulse and PRI sequence
pools to enable multi-wiphy operation on SMP systems.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current code unconditionally reads the target
power values for all modes from the EEPROM. However
In 'ar9003_hw_set_power_per_rate_table' the regulatory
caps are applied only on a mode specific subset of the
power values.
The reported TX power level is calculated from the
maximum of the power values. Because some of these
values are uncapped in certain cases, the reported
TX power will be wrong.
On the older chipset, we don't have such problems
because only the mode specific subset of the power
levels are retrieved from the EEPROM on those. Do
the same for the AR9003 chips to fix the issue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes two compile warnings, and removes a useless
cast when assigning the 'sc' variable.
Reported-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'ath9k_hw_update_regulatory_maxpower'
helper function has been introduced by
commit a55f858852
(ath9k_hw: Cleanup TX power calculation for AR9287).
Updating of the max_power_level value has been moved
into the helper function in that change, however the
removed code from 'ath9k_hw_ar9287_set_txpower' has
not been replaced with a call of the new helper
function.
Due to that missing call, retrieving tx power for 2x2
and 3x3 chainmask is not handled properly. During the
calculation of the tx power for 2x2 and 3x3 chainmasks
the values are reduced. Those reductions must be
compensated during retrieving.
Fix this by adding the missing call of the helper
function.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to unifying regulatory limit handling
commit ca2c68cc7b
(ath9k_hw: clean up tx power handling) introduced
a new helper function 'ath9k_hw_apply_txpower',
and the direct calls of 'ah->eep_ops->set_txpower'
has been replaced by a call of the helper function.
This caused a change in the behaviour of the
'ath9k_hw_set_txpowerlimit' function. The purpose
of that function is to calculate and store the
rate txpower table and the regulatory limit without
touching the hardware registers. Before the commit,
the 'test' parameter of the function was passed to
the 'ah->eep_ops->set_txpower'. Now the calling of
the 'set_txpower' function happens indirectly through
'ath9k_hw_apply_txpower', so the 'test' argument of
the 'set_txpower' is always 'false'.
This patch restores the original behaviour of
'ath9k_hw_set_txpowerlimit' by adding a new
argument to 'ath9k_hw_apply_txpower.'
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Complete the waiting fwlog_block_read on debugfs cleanup, otherwise
userspace and module unload might softlock.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is supposed to be pushed in one indent level.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The original conditions are always true. I think && was intended here,
but I don't have the hardware to test. Could you take a look?
kvalo: Chilam confirmed that the fix is valid
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ath6kl fw does not have enough memory to support the WoW filters of
more than one vif. Disallow WoW suspend if this is the case.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Now that we know the supported PHY capabilities, only restore supported
bands / HT capabilities in firmware when stopping AP.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently the supported bands are just hard coded in the driver.
However, the ath6kl FW will include its 11n and band capabilites in a
WMI_READY event. Handle this and report capabilites to cfg80211
accordingly.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath6kl: If wow deepsleep pno suspend failure driver will choose cutpower.
in this scenario MMC_PM_KEEP_POWER should be cleared so that mmc will power
off the ar6000
kvalo: remove extra parenthesis
Signed-off-by: Ming Jiang <mjiang@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Set max_scan_ssids and max_sched_scan_ssids to same value. These use the
same probed SSID list, so there is no point in using different maximum
number of SSIDs.
Clear probed SSID entries that are not used. This was already done for
sched_scan, but not for scan. Be consistent and clear the table for both
cases to avoid leaving bogus entries.
In addition, share the same function for setting the probed SSIDs for
scan and sched_scan paths. This fixes setting of wildcard SSID flag
(ANY_SSID_FLAG) and changes the scan path to use probed SSID index
consistently (i.e., start with 0 similarly to sched_scan; firmware
will handle the needed internal mapping).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath6kl does not support Probe Response offloading for Interworking (IEEE
802.11u), so remove the incorrectly added capability flag for it.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Background scan interval should not be modified while starting
schedule scanning as it changes the bg scan interval when connected to AP.
Use the currently configured interval instead.
kvalo: improve commit log
Signed-off-by: Subramania Sharma <sharmat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Added a new member bg_scan_period in struct ath6kl_vif
to retain background scan period value configured via debugfs
entry 'bgscan_interval'. This backup is needed in schedule scan
path while configuring scan parameters.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The FBIN2FREQ macro and the ath9k_hw_fbin2freq function
does the same thing. Remove the macro, and use the inline
function instead.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both eeprom.c and ar9003_eeprom.c has an indentical
'ath9k_hw_fbin2freq' function. Move the function to
a common place and remove the duplicates.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The existing constants are used for reduction/increase
tx power level on devices with 2x2 and 3x3 chainmask.
Both reduction and increase must use the same value, so
it makes no sense to use separate constants for them.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Assigning sequence number for frames without taking care
of the fragment field breaks transmission of fragmented frames.
Fix this by assigning the fragment number properly.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The computation of the scaled power value in
various eeprom files uses identical code. Move
that code into a helper function and use that
instead of code duplication.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The REDUCE_SCALED_POWER_BY_THREE_CHAIN symbol is
defined in different eeprom files, and the value
varies between the different files.
In eeprom_def.c and in ar9003_eeprom.c the value
of the symbol is 9, however the comments in these
files indicates the value should be 10*log10(3)*2
which is 9.54242509439325. Replace the the value
to 10 in these files.
Also add comments to eeprom_9287.c.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have a helper function for updating the max_power_level
value. Use that and remove the duplicated code.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch converts the drivers in drivers/net/wireless/* to use
module_pci_driver() macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Simon Kelley <simon@thekelleys.org.uk>
Cc: Jouni Malinen <j@w1.fi>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: linux-wireless@vger.kernel.org
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The tx interrupt for beacon queue is configured only for edma chips.
As the edma chip does not support per descriptor interrupt, no need to
set INTREQ for every beacon descriptor. And also clear ps filter for
beacon frame.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever the reset work is queued up, do not generate beacon. And also
clear the beacon miss count once the beacon stuck was observed.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After the chip reset, the noise immunity levels are restored with
history values. If the immunity levels are lower than the defaults,
lets start with the optimal values.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sync-up ibss beacon timer with the beacon frame's timestamp. When the
node acts as joiner, it has to sync with the received beacon timestamp
instead of reading tsf from hw. As the hw tsf wont wont be update till
bssid is configured. This patch programs hw tsf with the received beacon
timestamp if beacon timers are yet to be configured.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
