commit 303911cfc5b95d33687d9046133ff184cf5043ff upstream.
The syzbot fuzzer has found two (!) races in the USB character device
registration and deregistration routines. This patch fixes the races.
The first race results from the fact that usb_deregister_dev() sets
usb_minors[intf->minor] to NULL before calling device_destroy() on the
class device. This leaves a window during which another thread can
allocate the same minor number but will encounter a duplicate name
error when it tries to register its own class device. A typical error
message in the system log would look like:
sysfs: cannot create duplicate filename '/class/usbmisc/ldusb0'
The patch fixes this race by destroying the class device first.
The second race is in usb_register_dev(). When that routine runs, it
first allocates a minor number, then drops minor_rwsem, and then
creates the class device. If the device creation fails, the minor
number is deallocated and the whole routine returns an error. But
during the time while minor_rwsem was dropped, there is a window in
which the minor number is allocated and so another thread can
successfully open the device file. Typically this results in
use-after-free errors or invalid accesses when the other thread closes
its open file reference, because the kernel then tries to release
resources that were already deallocated when usb_register_dev()
failed. The patch fixes this race by keeping minor_rwsem locked
throughout the entire routine.
Reported-and-tested-by: syzbot+30cf45ebfe0b0c4847a1@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1908121607590.1659-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e2a589a3fc36ce858d42e767c3bcd8fc62a512b upstream.
`dt3k_ns_to_timer()` determines the prescaler and divisor to use to
produce a desired timing period. It is influenced by a rounding mode
and can round the divisor up, down, or to the nearest value. However,
the code for rounding up currently does the same as rounding down! Fix
ir by using the `DIV_ROUND_UP()` macro to calculate the divisor when
rounding up.
Also, change the types of the `divider`, `base` and `prescale` variables
from `int` to `unsigned int` to avoid mixing signed and unsigned types
in the calculations.
Also fix a typo in a nearby comment: "improvment" => "improvement".
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190812120814.21188-1-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4d98bc3fc93ec3a58459948a2c0e0c9b501cd88 upstream.
In `dt3k_ns_to_timer()` the following lines near the end of the function
result in a signed integer overflow:
prescale = 15;
base = timer_base * (1 << prescale);
divider = 65535;
*nanosec = divider * base;
(`divider`, `base` and `prescale` are type `int`, `timer_base` and
`*nanosec` are type `unsigned int`. The value of `timer_base` will be
either 50 or 100.)
The main reason for the overflow is that the calculation for `base` is
completely wrong. It should be:
base = timer_base * (prescale + 1);
which matches an earlier instance of this calculation in the same
function.
Reported-by: David Binderman <dcb314@hotmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20190812111517.26803-1-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cbedfe11347fe418621bd188d58a206beb676218 ]
Commit d66acc39c7 ("bitops: Optimise get_order()") introduced a
compilation warning because "rx_frag_size" is an "ushort" while
PAGE_SHIFT here is 16.
The commit changed the get_order() to be a multi-line macro where
compilers insist to check all statements in the macro even when
__builtin_constant_p(rx_frag_size) will return false as "rx_frag_size"
is a module parameter.
In file included from ./arch/powerpc/include/asm/page_64.h:107,
from ./arch/powerpc/include/asm/page.h:242,
from ./arch/powerpc/include/asm/mmu.h:132,
from ./arch/powerpc/include/asm/lppaca.h:47,
from ./arch/powerpc/include/asm/paca.h:17,
from ./arch/powerpc/include/asm/current.h:13,
from ./include/linux/thread_info.h:21,
from ./arch/powerpc/include/asm/processor.h:39,
from ./include/linux/prefetch.h:15,
from drivers/net/ethernet/emulex/benet/be_main.c:14:
drivers/net/ethernet/emulex/benet/be_main.c: In function 'be_rx_cqs_create':
./include/asm-generic/getorder.h:54:9: warning: comparison is always
true due to limited range of data type [-Wtype-limits]
(((n) < (1UL << PAGE_SHIFT)) ? 0 : \
^
drivers/net/ethernet/emulex/benet/be_main.c:3138:33: note: in expansion
of macro 'get_order'
adapter->big_page_size = (1 << get_order(rx_frag_size)) * PAGE_SIZE;
^~~~~~~~~
Fix it by moving all of this multi-line macro into a proper function,
and killing __get_order() off.
[akpm@linux-foundation.org: remove __get_order() altogether]
[cai@lca.pw: v2]
Link: http://lkml.kernel.org/r/1564000166-31428-1-git-send-email-cai@lca.pw
Link: http://lkml.kernel.org/r/1563914986-26502-1-git-send-email-cai@lca.pw
Fixes: d66acc39c7 ("bitops: Optimise get_order()")
Signed-off-by: Qian Cai <cai@lca.pw>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Howells <dhowells@redhat.com>
Cc: Jakub Jelinek <jakub@redhat.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Bill Wendling <morbo@google.com>
Cc: James Y Knight <jyknight@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7bc36e3ce91471b6377c8eadc0a2f220a2280083 ]
Fixes gcc '-Wunused-but-set-variable' warning:
fs/ocfs2/xattr.c: In function ocfs2_xattr_bucket_find:
fs/ocfs2/xattr.c:3828:6: warning: variable last_hash set but not used [-Wunused-but-set-variable]
It's never used and can be removed.
Link: http://lkml.kernel.org/r/20190716132110.34836-1-yuehaibing@huawei.com
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61f259821dd3306e49b7d42a3f90fb5a4ff3351b ]
Some processors may mispredict an array bounds check and
speculatively access memory that they should not. With
a user supplied array index we like to play things safe
by masking the value with the array size before it is
used as an index.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/r/20190731043957.GA1600@agluck-desk2.amr.corp.intel.com
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb4819934a7f9b87876f11ed05b8624c0114551b ]
KBUILD_EXTRA_SYMBOLS makes sense only when building external modules.
Moreover, the modpost sets 'external_module' if the -e option is given.
I replaced $(patsubst %, -e %,...) with simpler $(addprefix -e,...)
while I was here.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 090bb803708198e5ab6b0046398c7ed9f4d12d6b ]
Retrieving PHYs can defer the probe, do not spawn an error when
-EPROBE_DEFER is returned, it is normal behavior.
Fixes: b1a9edbda0 ("ata: libahci: allow to use multiple PHYs")
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eeebce1862970653cdf5c01e98bc669edd8f529a ]
Reviewed-by: Bader Ali - Saleh <bader.alisaleh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71d6c505b4d9e6f76586350450e785e3d452b346 ]
Jeffrin reported a KASAN issue:
BUG: KASAN: global-out-of-bounds in ata_exec_internal_sg+0x50f/0xc70
Read of size 16 at addr ffffffff91f41f80 by task scsi_eh_1/149
...
The buggy address belongs to the variable:
cdb.48319+0x0/0x40
Much like commit 18c9a99bce2a ("libata: zpodd: small read overflow in
eject_tray()"), this fixes a cdb[] buffer length, this time in
zpodd_get_mech_type():
We read from the cdb[] buffer in ata_exec_internal_sg(). It has to be
ATAPI_CDB_LEN (16) bytes long, but this buffer is only 12 bytes.
Reported-by: Jeffrin Jose T <jeffrin@rajagiritech.edu.in>
Fixes: afe7595118 ("libata: identify and init ZPODD devices")
Link: https://lore.kernel.org/lkml/201907181423.E808958@keescook/
Tested-by: Jeffrin Jose T <jeffrin@rajagiritech.edu.in>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20f9781f491360e7459c589705a2e4b1f136bee9 ]
When building our local version of perf with MSAN (Memory Sanitizer) and
running the perf record command, MSAN throws a use of uninitialized
value warning in "tools/perf/util/util.c:333:6".
This warning stems from the "buf" variable being passed into "write".
It originated as the variable "ev" with the type union perf_event*
defined in the "perf_event__synthesize_attr" function in
"tools/perf/util/header.c".
In the "perf_event__synthesize_attr" function they allocate space with a malloc
call using ev, then go on to only assign some of the member variables before
passing "ev" on as a parameter to the "process" function therefore "ev"
contains uninitialized memory. Changing the malloc call to zalloc to initialize
all the members of "ev" which gets rid of the warning.
To reproduce this warning, build perf by running:
make -C tools/perf CLANG=1 CC=clang EXTRA_CFLAGS="-fsanitize=memory\
-fsanitize-memory-track-origins"
(Additionally, llvm might have to be installed and clang might have to
be specified as the compiler - export CC=/usr/bin/clang)
then running:
tools/perf/perf record -o - ls / | tools/perf/perf --no-pager annotate\
-i - --stdio
Please see the cover letter for why false positive warnings may be
generated.
Signed-off-by: Numfor Mbiziwo-Tiapo <nums@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Drayton <mbd@fb.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/20190724234500.253358-2-nums@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7622236ceb167aa3857395f9bdaf871442aa467e ]
So I have been having lots of trouble with hand-crafted perf.data files
causing segfaults and the like, so I have started fuzzing the perf tool.
First issue found:
If f_header.attr_size is 0 in the perf.data file, then perf will crash
with a divide-by-zero error.
Committer note:
Added a pr_err() to tell the user why the command failed.
Signed-off-by: Vince Weaver <vincent.weaver@maine.edu>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.21.1907231100440.14532@macbook-air
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a446ef08f3bfc0c3deb9c6be840af2528ef8cf8 ]
The GPCv2 is a stacked IRQ controller below the ARM GIC. It doesn't
care about the IRQ type itself, but needs to forward the type to the
parent IRQ controller, so this one can be configured correctly.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09e088a4903bd0dd911b4f1732b250130cdaffed ]
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/xen/xen-pciback/conf_space_capability.c: In function pm_ctrl_write:
drivers/xen/xen-pciback/conf_space_capability.c:119:25: warning:
variable old_state set but not used [-Wunused-but-set-variable]
It is never used so can be removed.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 224c04973db1125fcebefffd86115f99f50f8277 upstream.
get_registers() may fail with -ENOMEM and in this
case we can read a garbage from the status variable tmp.
Reported-by: syzbot+3499a83b2d062ae409d4@syzkaller.appspotmail.com
Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 849f5ae3a513c550cad741c68dd3d7eb2bcc2a2c upstream.
The endpoint type should also be checked before a device
is accepted.
Reported-by: syzbot+5efc10c005014d061a74@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c88090dfc84254fa149174eb3e6a8458de1912c4 upstream.
The driver should check whether the endpoint it uses has the correct
type.
Reported-by: syzbot+c7df50363aaff50aa363@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01ec0a5f19c8c82960a07f6c7410fc9e01d7fb51 upstream.
The ioctl handler uses the intfdata of a second interface,
which may not be present in a broken or malicious device, hence
the intfdata needs to be checked for NULL.
[jkosina@suse.cz: fix newly added spurious space]
Reported-by: syzbot+965152643a75a56737be@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cfef67f016e4c00a2f423256fc678a6967a9fc09 upstream.
In snd_hda_parse_generic_codec(), 'spec' is allocated through kzalloc().
Then, the pin widgets in 'codec' are parsed. However, if the parsing
process fails, 'spec' is not deallocated, leading to a memory leak.
To fix the above issue, free 'spec' before returning the error.
Fixes: 352f7f914e ("ALSA: hda - Merge Realtek parser code to generic parser")
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7fafcfdf6377b18b2a726ea554d6e593ba44349f upstream.
It looks like there is a possibility of a double-free vulnerability on an
error path of the f_midi_set_alt function in the f_midi driver. If the
path is feasible then free_ep_req gets called twice:
req->complete = f_midi_complete;
err = usb_ep_queue(midi->out_ep, req, GFP_ATOMIC);
=> ...
usb_gadget_giveback_request
=>
f_midi_complete (CALLBACK)
(inside f_midi_complete, for various cases of status)
free_ep_req(ep, req); // first kfree
if (err) {
ERROR(midi, "%s: couldn't enqueue request: %d\n",
midi->out_ep->name, err);
free_ep_req(midi->out_ep, req); // second kfree
return err;
}
The double-free possibility was introduced with commit ad0d1a058e
("usb: gadget: f_midi: fix leak on failed to enqueue out requests").
Found by MOXCAFE tool.
Signed-off-by: Tuba Yavuz <tuba@ece.ufl.edu>
Fixes: ad0d1a058e ("usb: gadget: f_midi: fix leak on failed to enqueue out requests")
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f0f1b8cac4d8d973e95f25d9ea132775fb43c5f4 upstream.
This ensures that the midi function will only work if the proper number of
IN and OUT requrests are allocated. Otherwise the function will work with less
requests then what the user wants.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
From: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ee1119d184bb06af921b48c3021d921bbd85bac upstream.
Add missing break statement in order to prevent the code from falling
through to case SH_BREAKPOINT_WRITE.
Fixes: 09a0729477 ("sh: hw-breakpoints: Add preliminary support for SH-4A UBC.")
Cc: stable@vger.kernel.org
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df9a606184bfdb5ae3ca9d226184e9489f5c24f7 upstream.
Although SAS3 & SAS3.5 IT HBA controllers support 64-bit DMA addressing, as
per hardware design, if DMA-able range contains all 64-bits
set (0xFFFFFFFF-FFFFFFFF) then it results in a firmware fault.
E.g. SGE's start address is 0xFFFFFFFF-FFFF000 and data length is 0x1000
bytes. when HBA tries to DMA the data at 0xFFFFFFFF-FFFFFFFF location then
HBA will fault the firmware.
Driver will set 63-bit DMA mask to ensure the above address will not be
used.
Cc: <stable@vger.kernel.org> # 5.1.20+
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df612421fe2566654047769c6852ffae1a31df16 upstream.
Commit 63d7ef36103d ("mwifiex: Don't abort on small, spec-compliant
vendor IEs") adjusted the ieee_types_vendor_header struct, which
inadvertently messed up the offsets used in
mwifiex_is_wpa_oui_present(). Add that offset back in, mirroring
mwifiex_is_rsn_oui_present().
As it stands, commit 63d7ef36103d breaks compatibility with WPA (not
WPA2) 802.11n networks, since we hit the "info: Disable 11n if AES is
not supported by AP" case in mwifiex_is_network_compatible().
Fixes: 63d7ef36103d ("mwifiex: Don't abort on small, spec-compliant vendor IEs")
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d33096a460d5b9bd13300f01615df5bb454db10 upstream.
We had a report of a server which did not do a DFS referral
because the session setup Capabilities field was set to 0
(unlike negotiate protocol where we set CAP_DFS). Better to
send it session setup in the capabilities as well (this also
more closely matches Windows client behavior).
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e99c63e4d86d3a94818693147b469fa70de6f945 upstream.
Currently we skip SMB2_TREE_CONNECT command when checking during
reconnect because Tree Connect happens when establishing
an SMB session. For SMB 3.0 protocol version the code also calls
validate negotiate which results in SMB2_IOCL command being sent
over the wire. This may deadlock on trying to acquire a mutex when
checking for reconnect. Fix this by skipping SMB2_IOCL command
when doing the reconnect check.
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05aaa5c97dce4c10a9e7eae2f1569a684e0c5ced upstream.
In a very similar spirit to commit c470bdc1aaf3 ("mac80211: don't WARN
on bad WMM parameters from buggy APs"), an AP may not transmit a
fully-formed WMM IE. For example, it may miss or repeat an Access
Category. The above loop won't catch that and will instead leave one of
the four ACs zeroed out. This triggers the following warning in
drv_conf_tx()
wlan0: invalid CW_min/CW_max: 0/0
and it may leave one of the hardware queues unconfigured. If we detect
such a case, let's just print a warning and fall back to the defaults.
Tested with a hacked version of hostapd, intentionally corrupting the
IEs in hostapd_eid_wmm().
Cc: stable@vger.kernel.org
Signed-off-by: Brian Norris <briannorris@chromium.org>
Link: https://lore.kernel.org/r/20190726224758.210953-1-briannorris@chromium.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1be3c1fae6c1e1f5bb982b255d2034034454527a upstream.
In iso_packets_buffer_init(), 'b->packets' is allocated through
kmalloc_array(). Then, the aligned packet size is checked. If it is
larger than PAGE_SIZE, -EINVAL will be returned to indicate the error.
However, the allocated 'b->packets' is not deallocated on this path,
leading to a memory leak.
To fix the above issue, free 'b->packets' before returning the error code.
Fixes: 31ef9134eb ("ALSA: add LaCie FireWire Speakers/Griffin FireWave Surround driver")
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org> # v2.6.39+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 38ada2f406a9b81fb1249c5c9227fa657e7d5671 upstream.
The code to detect if in4 is present is wrong; if in4 is not present,
the in4_input sysfs attribute is still present.
In detail:
- Ihen RTD3_MD=11 (VSEN3 present), everything is as expected (no bug).
- If we have RTD3_MD!=11 (no VSEN3), we unexpectedly have a in4_input
file under /sys and the "sensors" command displays in4_input.
But as expected, we have no in4_min, in4_max, in4_alarm, in4_beep.
Fix is_visible function to detect and report in4_input visibility
as expected.
Reported-by: Gilles Buloz <Gilles.Buloz@kontron.com>
Cc: Gilles Buloz <Gilles.Buloz@kontron.com>
Cc: stable@vger.kernel.org
Fixes: 3434f37835 ("hwmon: Driver for Nuvoton NCT7802Y")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 30a8beeb3042f49d0537b7050fd21b490166a3d9 upstream.
Uninitialized Kernel memory can leak to USB devices.
Fix by using kzalloc() instead of kmalloc() on the affected buffers.
Signed-off-by: Tomas Bortoli <tomasbortoli@gmail.com>
Reported-by: syzbot+513e4d0985298538bf9b@syzkaller.appspotmail.com
Fixes: 0a25e1f4f1 ("can: peak_usb: add support for PEAK new CANFD USB adapters")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ead16e53c2f0ed946d82d4037c630e2f60f4ab69 upstream.
Uninitialized Kernel memory can leak to USB devices.
Fix by using kzalloc() instead of kmalloc() on the affected buffers.
Signed-off-by: Tomas Bortoli <tomasbortoli@gmail.com>
Reported-by: syzbot+d6a5a1a3657b596ef132@syzkaller.appspotmail.com
Fixes: f14e22435a ("net: can: peak_usb: Do not do dma on the stack")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4ce54af8b33d3e21ca935fc1b89b58cbba956051 ]
Some hardware PMU drivers will override perf_event.cpu inside their
event_init callback. This causes a lockdep splat when initialized through
the kernel API:
WARNING: CPU: 0 PID: 250 at kernel/events/core.c:2917 ctx_sched_out+0x78/0x208
pc : ctx_sched_out+0x78/0x208
Call trace:
ctx_sched_out+0x78/0x208
__perf_install_in_context+0x160/0x248
remote_function+0x58/0x68
generic_exec_single+0x100/0x180
smp_call_function_single+0x174/0x1b8
perf_install_in_context+0x178/0x188
perf_event_create_kernel_counter+0x118/0x160
Fix this by calling perf_install_in_context with event->cpu, just like
perf_event_open
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Frank Li <Frank.li@nxp.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Link: https://lkml.kernel.org/r/c4ebe0503623066896d7046def4d6b1e06e0eb2e.1563972056.git.leonard.crestez@nxp.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 952041a8639a7a3a73a2b6573cb8aa8518bc39f8 ]
While reviewing rwsem down_slowpath, Will noticed ldsem had a copy of
a bug we just found for rwsem.
X = 0;
CPU0 CPU1
rwsem_down_read()
for (;;) {
set_current_state(TASK_UNINTERRUPTIBLE);
X = 1;
rwsem_up_write();
rwsem_mark_wake()
atomic_long_add(adjustment, &sem->count);
smp_store_release(&waiter->task, NULL);
if (!waiter.task)
break;
...
}
r = X;
Allows 'r == 0'.
Reported-by: Will Deacon <will@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Will Deacon <will@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 4898e640ca ("tty: Add timed, writer-prioritized rw semaphore")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b5f307ef3cb5022bfe3c8ca5b8f2114d5bf6c29 ]
While loading fw crashdump in function fw_crash_buffer_show(), left bytes
in one dma chunk was not checked, if copying size over it, overflow access
will cause kernel panic.
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d64b212ea960db4276a1d8372bd98cb861dfcbb0 ]
When building a multiplatform kernel that includes armv4 support,
the default target CPU does not support the blx instruction,
which leads to a build failure:
arch/arm/mach-davinci/sleep.S: Assembler messages:
arch/arm/mach-davinci/sleep.S:56: Error: selected processor does not support `blx ip' in ARM mode
Add a .arch statement in the sources to make this file build.
Link: https://lore.kernel.org/r/20190722145211.1154785-1-arnd@arndb.de
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d95daf5accf4a72005daa13fbb1d1bd8709f2861 ]
When perf_add_probe_events() we call cleanup_perf_probe_events() for the
pev pointer it receives, then, as part of handling this failure the main
'perf probe' goes on and calls cleanup_params() and that will again call
cleanup_perf_probe_events()for the same pointer, so just set nevents to
zero when handling the failure of perf_add_probe_events() to avoid the
double free.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https://lkml.kernel.org/n/tip-x8qgma4g813z96dvtw9w219q@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b8179944cb0dd53e5223996966746cdc8a60657 ]
Draining makes little sense in the situation of hardware overrun, as the
hardware will have consumed all its available samples. Additionally,
draining whilst the stream is paused would presumably get stuck as no
data is being consumed on the DSP side.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26c3f1542f5064310ad26794c09321780d00c57d ]
Currently, whilst in SNDRV_PCM_STATE_OPEN it is possible to call
snd_compr_stop, snd_compr_drain and snd_compr_partial_drain, which
allow a transition to SNDRV_PCM_STATE_SETUP. The stream should
only be able to move to the setup state once it has received a
SNDRV_COMPRESS_SET_PARAMS ioctl. Fix this issue by not allowing
those ioctls whilst in the open state.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4475f8c4ab7b248991a60d9c02808dbb813d6be8 ]
A previous fix to the stop handling on compressed capture streams causes
some knock on issues. The previous fix updated snd_compr_drain_notify to
set the state back to PREPARED for capture streams. This causes some
issues however as the handling for snd_compr_poll differs between the
two states and some user-space applications were relying on the poll
failing after the stream had been stopped.
To correct this regression whilst still fixing the original problem the
patch was addressing, update the capture handling to skip the PREPARED
state rather than skipping the SETUP state as it has done until now.
Fixes: 4f2ab5e1d13d ("ALSA: compress: Fix stop handling on compressed capture streams")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6ec414a4dd529eeac5c3ea51c661daba3397108 ]
If the device driver were to send out a full queue's worth of SBALs,
current code would end up discovering the last of those SBALs as PRIMED
and erroneously skip the SIGA-w. This immediately stalls the queue.
Add a check to not attempt fast-requeue in this case. While at it also
make sure that the state of the previous SBAL was successfully extracted
before inspecting it.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0a12445d1cb186d875410d093a00d215bec6a89 ]
The cpu variable is still being used in the of_get_property() call
after the of_node_put() call, which may result in use-after-free.
Fixes: a9acc26b75f6 ("cpufreq/pasemi: fix possible object reference leak")
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d2b3fe42bc629c2d4002f652b3abdfb2e72991c7 ]
ieee80211_set_wmm_default() normally sets up the initial CW min/max for
each queue, except that it skips doing this if the driver doesn't
support ->conf_tx. We still end up calling drv_conf_tx() in some cases
(e.g., ieee80211_reconfig()), which also still won't do anything
useful...except it complains here about the invalid CW parameters.
Let's just skip the WARN if we weren't going to do anything useful with
the parameters.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Link: https://lore.kernel.org/r/20190718015712.197499-1-briannorris@chromium.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94bccc34071094c165c79b515d21b63c78f7e968 ]
iscsi_ibft can use ACPI to find the iBFT entry during bootup,
currently, ISCSI_IBFT depends on ISCSI_IBFT_FIND which is
a X86 legacy way to find the iBFT by searching through the
low memory. This patch changes the dependency so that other
arch like ARM64 can use ISCSI_IBFT as long as the arch supports
ACPI.
ibft_init() needs to use the global variable ibft_addr declared
in iscsi_ibft_find.c. A #ifndef CONFIG_ISCSI_IBFT_FIND is needed
to declare the variable if CONFIG_ISCSI_IBFT_FIND is not selected.
Moving ibft_addr into the iscsi_ibft.c does not work because if
ISCSI_IBFT is selected as a module, the arch/x86/kernel/setup.c won't
be able to find the variable at compile time.
Signed-off-by: Thomas Tai <thomas.tai@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b0890cd60829bd51455dc5ad689ed58c4408227 ]
Thomas and Juliana report a deadlock when running:
(rmmod nf_conntrack_netlink/xfrm_user)
conntrack -e NEW -E &
modprobe -v xfrm_user
They provided following analysis:
conntrack -e NEW -E
netlink_bind()
netlink_lock_table() -> increases "nl_table_users"
nfnetlink_bind()
# does not unlock the table as it's locked by netlink_bind()
__request_module()
call_usermodehelper_exec()
This triggers "modprobe nf_conntrack_netlink" from kernel, netlink_bind()
won't return until modprobe process is done.
"modprobe xfrm_user":
xfrm_user_init()
register_pernet_subsys()
-> grab pernet_ops_rwsem
..
netlink_table_grab()
calls schedule() as "nl_table_users" is non-zero
so modprobe is blocked because netlink_bind() increased
nl_table_users while also holding pernet_ops_rwsem.
"modprobe nf_conntrack_netlink" runs and inits nf_conntrack_netlink:
ctnetlink_init()
register_pernet_subsys()
-> blocks on "pernet_ops_rwsem" thanks to xfrm_user module
both modprobe processes wait on one another -- neither can make
progress.
Switch netlink_bind() to "nowait" modprobe -- this releases the netlink
table lock, which then allows both modprobe instances to complete.
Reported-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Reported-by: Juliana Rodrigueiro <juliana.rodrigueiro@intra2net.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fee6a8923ae0d318a7f7950c6c6c28a96cea099b upstream.
When closing the CAN device while tx skbs are inflight, echo skb could
be released twice. By calling close_candev() before unlinking all
pending tx urbs, then the internal echo_skb[] array is fully and
correctly cleared before the USB write callback and, therefore,
can_get_echo_skb() are called, for each aborted URB.
Fixes: bb4785551f ("can: usb: PEAK-System Technik USB adapters driver core")
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>