Printing the FIFO depth does not add much noise in the log and can be useful
for debugging transfer issues.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For spi without dma channel and use can_dma(), it can
use master->dev for struct device.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit ddcad7e906 omap2_mcspi_set_cs() is called without
runtime power management requested. This patch fixes the problem by
requesting runtime power management in omap2_mcspi_set_cs().
Reported-By: Pali Rohár <pali.rohar@gmail.com>
Fixes: ddcad7e906 (spi: omap2-mcspi: Fix native cs with new set_cs)
Tested-By: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the pre-scaler limit is incorrect. The value differs slightly
for various devices so a single value can't be used. Using the compatible
field select the correct pre-scaler limit.
Add new compatible field value for Keystone devices to support their
unique pre-scaler limit value.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Within davinci_spi_get_prescale() the prescale has two meanings. First one
being the calculated prescale value and then at the end translates it to the
prescale value that will be written to the SPI register.
At first glance this can be confusing especially when comparing the minimum
prescale value against what is seen in the TRM.
To simplify things make it clear that the calculated prescale value will always
be based on the value that will be written into the SPI register.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DMA transfers must be greater than the watermark level size. spi_imx->rx_wml
and spi_imx->tx_wml contain the watermark level in 32bit words whereas struct
spi_transfer contains the transfer len in bytes. Fix the check if DMA is
possible for a transfer accordingly. This fixes transfers with sizes between
33 and 128 bytes for which previously was claimed that DMA is possible.
Fixes: f62caccd12 (spi: spi-imx: add DMA support)
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes several warnings like:
drivers/spi/spi-mpc512x-psc.c: In function 'mpc512x_psc_spi_prep_xfer_hw':
arch/powerpc/include/asm/io.h:163:2: warning: '__ret' may be used uninitialized in this function [-Wmaybe-uninitialized]
introduced in commit 8bf960985d for some build configurations.
Fixes: 8bf960985d ("spi: mpc512x-psc: add support for Freescale MPC5125")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The register layout of the PSC devices differ between MPC5121 and
MPC5125, but the registers are named nearly identical and their purpose
is similar enough ("freescale identical") such that substituting
mpc52xx_psc by mpc5125_psc is nearly enough to make the driver work on
MPC5125. To keep supporting MPC5121 this patch introduces a cpp
macro to select the right struct that defines the register layout.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Clock provider drivers generally shouldn't include clk.h because
it's the consumer API. Remove the include here because this is a
provider driver.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a missing break statement here so selecting both only selects
upper.
Fixes: dfe11a11d5 ('spi: Add support for Zynq Ultrascale+ MPSoC GQSPI controller')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since spidev is no more allowed to use in DT and is really loudly warned about
it I'd like to add this compatible value.
(Geert Uytterhoeven wrote: "Add the compatible value for your device to the
spidev_dt_ids[] array in drivers/spi/spidev.c.")
Signed-off-by: Mark Brown <broonie@kernel.org>
per spi-master statistics accessible as:
/sys/class/spi_master/spi*/statistics/*
per spi-device statistics accessible via:
/sys/class/spi_master/spi*/spi*.*/statistics/*
The following statistics are exposed as separate "files" inside
these directories:
* messages number of spi_messages
* transfers number of spi_transfers
* bytes number of bytes transferred
* bytes_rx number of bytes transmitted
* bytes_tx number of bytes received
* errors number of errors encounterd
* timedout number of messages that have timed out
* spi_async number of spi_messages submitted using spi_async
* spi_sync number of spi_messages submitted using spi_sync
* spi_sync_immediate number of spi_messages submitted using spi_sync,
that are handled immediately without a context switch
to the spi_pump worker-thread
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit a483dcbfa2 ("ARM: shmobile: lager: Remove legacy
board support"), R-Car Gen2 SoCs are only supported in generic DT-only
ARM multi-platform builds. The driver doesn't need to match platform
devices by name anymore, hence remove the corresponding
platform_device_id entry.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mark Brown <broonie@kernel.org>
Memory for struct rockchip_spi is allocated by spi_alloc_master()
using kzalloc() so it doesn't need to be set to 0 one more time.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Memory for this struct is allocated by spi_alloc_master() using
kzalloc() so it doesn't need to be set to 0 one more time.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
spi_map_buf() processes mapping of vmalloc-ed buffers in a special way,
making mapping of every page separately. However, if the buffer is not
aligned to page boundary (e.g. sub-array in a vmalloc-ed array), it
fills the scatter table with page-size unaligned pieces, that cross
page boundaries. This is incorrect and can, for example, cause memory
corruption and various crashes when working with ubifs on spi-nor chips
(though those drivers are themselves buggy in that they should be
providing DMAable memory to the SPI framework).
Fix this by using proper scatter table size and intra-page buffer lengths,
so that the whole buffer splits into separate scatter table entries on
page boundaries.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Maximum speed supported by spfi is limited to 1/4 of the spfi clock.
But in some SoCs the maximum speed supported by the spfi block can
be limited to less than 1/4 of the spfi clock. In such cases we have
to define the limit in the device tree so that the driver can pick
it up.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
qspi_set_send_trigger() returns an unsigned value, so make it return
"unsigned int".
Update the loop variables qspi_trigger_transfer_out_int() to match the
above.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Just use "ret" instead, for consistency with other similar functions.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Setting the Same Edge bit indicates to the spfi block to receive and
transmit data on the same edge of the spfi clock, which in turn
doubles the operating frequency of spfi.
The maximum supported frequency is limited to 1/4th of the spfi input
clock, but without this bit set the maximum would be 1/8th of the
input clock.
The current driver calculates the divisor with maximum speed at 1/4th
of the input clock, this would fail if the requested frequency is
higher than 1/8 of the input clock. Any requests for 1/8th of the
input clock would still pass.
Fixes: 8543d0e72d ("spi: img-spfi: Limit bit clock to 1/4th of input clock")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The latest SPI controllers embedded inside sama5d2x SoCs come with FIFOs.
When FIFOs are enabled, they can either work in SINGLE data mode or
MULTIPLE data mode. The selected mode depends on the configuration of the
SPI controller (see below).
In SINGLE data mode (or legacy mode), for a single I/O access, only one
data can be read from the Receive Data Register (RDR) or written into the
Transmit Data Register (TDR). On the other hand, in MULTIPLE data mode, up
to 4 data can be read from the RDR or up 2 data can be written into the
TDR in a single 32bit I/O access. So programmers should take good care of
the width of the I/O access to read/write the right number of data. The
exact number of read/written data depends on both the I/O access width and
the data width (from 8 up to 16 bits).
To enable the FIFO feature a "atmel,fifo-size" property must be set to
provide the maximum number of data (not bytes) the RX and TX FIFOs can
store. Hence a 32 data FIFO can always store up to 32 data unrelated with
the actual data width.
When FIFOs are enabled, the RX one is forced to operate in SINGLE data
mode because this driver configures the spi controller as a master. In
master mode only, the Received Data Register has an additionnal Peripheral
Chip Select field, which prevents us from reading more than a single data
at each register access.
Besides, the TX FIFO operates in MULTIPLE data mode. However, even when a
8bit data size is used, only two data by access could be written into the
Transmit Data Register. Indeed the first data has to be written into the
lowest 16 bits whereas the second data has to be written into the highest
16 bits of the TDR. When DMA transfers are used to send data, we don't
rework the transmit buffer to cope with this hardware limitation: the
additional copies required to prepare a new input buffer suited to both
the DMA controller and the spi controller would waste all the benefit of
the DMA transfer. Instead, the DMA controller is configured to write only
one data at time into the TDR.
In pio mode, two data are written in the TDR in a single access.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Constify the ACPI device ID array, it doesn't need to be writable at
runtime.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for GQSPI controller driver used by
Zynq Ultrascale+ MPSoC
Signed-off-by: Ranjit Waghmode <ranjit.waghmode@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI hardware spec for Keystone specify a lower value of 0 for pre-scale
divider which determine what max value of spi clock (spi-max-frequency)
the device can support. This translates to a clock divider of 2. So fix
the lower limit value used for the boundary check in
davinci_spi_get_prescale() function to 1 so that a maximum of spi device
clock rate / 2 is possible to be set for spi-max-frequency.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In current driver, we increase actual_length in the following way:
message->actual_length += dspi_xxx_transfer()
It has two defects.
First, transmitting maybe in process when the function call finished and
we don't know the transmitting result in this moment.
Secondly, the last sentence in function before returning is accessing the
SPI register and trigger the data transmitting. If we enable interrupt,
interrupt may be generated before function return and we also have the same
sentence "message->actual_length += dspi_xxx_transfer()"
in the IRQ handler.
And usually dspi_xxx_transfer will trigger a new IRQ.
The original dspi_xxx_transfer call may return when no new IRQ generate.
This may mess the variable spi_message->actual_length.
Now we increase the variable in the IRQ handler and only when we get the
TCF or EOQ interrupt
And we get the transmitted data length from the SPI transfer counter
instead of the function return value.
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DSPI module has two optional interrupts when complete data transfer.
One is EOQ interrupt, the other one is TCF interrupt.
EOQ indicates a queue of data frame has been transmitted.
TCF indicates a frame has been transmitted.
This patch enable support TCF mode.
Driver binds a correct interrupt mode to every compatible string.
User should use the correct compatible string in the dts node.
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch relies on the CSAAT (Chip Select Active After Transfer) feature
introduced by the version 2 of the spi controller. This new mode allows to
use properly the internal chip-select output pin of the spi controller
instead of using external gpios. Consequently, the "cs-gpios" device-tree
property becomes optional.
When the new CSAAT bit is set into the Chip Select Register, the internal
chip-select output pin remains asserted till both the following conditions
become true:
- the LASTXFER bit is set into the Control Register (or the Transmit Data
Register)
- the Transmit Data Register and its shift register are empty.
WARNING: if the LASTXFER bit is set into the Control Register then new
data are written into the Transmit Data Register fast enough to keep its
shifter not empty, the chip-select output pin remains asserted. Only when
the shifter becomes empty, the chip-select output pin is unasserted.
When the CSAAT bit is clear in the Chip Select Register, the LASTXFER bit
is ignored in both the Control Register and the Transmit Data Register.
The internal chip-select output pin remains active as long as the Transmit
Data Register or its shift register are not empty.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Generic DMA support was already implemented by commit cd7bed0034
("spi/pxa2xx: break out the private DMA API usage into a separate file")
which moved all the legacy PXA DMA implementation code into its own
file.
With generic DMA available for PXA, we can now just trash this file.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Mark Brown <broonie@linaro.org>
[respin after pxa dmaengine support upstream]
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
General register located in LPSS SPI private register space is not found in
upcoming Intel LPSS platforms. Access it conditionally depending is it
defined in configuration.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some of the Intel LPSS SPI properties will be different in upcoming
platforms compared to existing Lynxpoint and BayTrail/Braswell. LPSS SPI
private registers will be at different offset and there will be changes in
individual registers and default FIFO thresholds too.
Add configuration for these differences and use them in runtime based on
LPSS SSP type. With this change private registers offset autodetection
becomes needless.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Intel LPSS SPI properties differ between between platforms. Now private
registers offset 0x400 or 0x800 is autodetected but there is need to
support also other offset and handle a few other differences.
Prepare for that by splitting the LPSS_SSP type into compatible hardware
types and set it now based on PCI or ACPI ID. That type will be used to set
properties that differ between current and upcoming platforms.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The case where spi_master sets the flags SPI_MASTER_MUST_RX/TX while
CONFIG_HAS_DMA is unset (which is unlikley) together with a driver
that reuses spi_messages with rx/tx_buff set to NULL, can result in:
* data disclosure over the SPI (for tx_buf == NULL)
* memory corruption (for rx_buf == NULL)
This happenes when dummy_rx/dummy_tx are changing address due to krealloc
or free and an allocation of the memory by a different part of the kernel.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
To reduce complexity of code, drop "ret" then qspi_transfer_out_in function
should return the value of "qspi_trigger_transfer_out_in" directly.
Signed-off-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
The name of "qspi_trigger_transfer_out_int" function should be
"qspi_trigger_transfer_out_in" without "t".
Signed-off-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
The commit df59fa7f4b "spi: orion: support armada extended baud
rates" made the assumptions that all the Armada SoCs supported the
same maximum frequency. However, according the hardware datasheet, the
maximum frequency supported by the Armada 370 SoC is tclk/4, for the
Armada XP, Armada 38x and Armada 39x SoCs the limitation is 50MHz and
for the Armada 375 it is tclk/15.
This patch introduces new compatible strings to handle all these
case. In order to be future proof a compatible was created for each
SoC even if currently some SoCs seem using the same IP.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
