Add parent_hwmod pointer to omap_hwmod. This can be set to point to a
"parent" hwmod that needs to be enabled for the "child" hwmod to work.
This is used at hwmod setup time: when doing the initial setup and
reset, first enable the parent hwmod, and after setup and reset is done,
restore the parent hwmod to postsetup_state.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit.taneja@gmail.com>
[paul@pwsan.com: add kerneldoc documentation for parent_hwmod; note that it
is a temporary workaround]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This updates platform data related to Si4713, which
has been updated to be compatible with DT interface.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Most of the patches are clock-related. The DPLL implementation is
changed to better align to the common clock framework.
There is also a patch that removes a few lines from the hwmod code -
this patch should have no functional effect.
Basic build, boot, and PM test logs for these patches can be found here:
http://www.pwsan.com/omap/testlogs/omap-a-for-v3.19/20141113094101/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tw+W
-----END PGP SIGNATURE-----
Merge tag 'for-v3.19/omap-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.19/soc
Some OMAP clock/hwmod patches for v3.19.
Most of the patches are clock-related. The DPLL implementation is
changed to better align to the common clock framework.
There is also a patch that removes a few lines from the hwmod code -
this patch should have no functional effect.
Basic build, boot, and PM test logs for these patches can be found here:
http://www.pwsan.com/omap/testlogs/omap-a-for-v3.19/20141113094101/
ml->node and sl->node are currently initialized
by means of INIT_LIST_HEAD(). That initialiation
is followed by a list_add() call.
Looking at what both these functions do we will have:
ml->node.next = &ml->node;
ml->node.prev = &ml->node;
oi->master->master_ports.next.prev = &ml->node;
ml->node.next = &oi->master->master_ports.next;
ml->node.prev = &oi->master->master_ports;
oi->master->master_ports.next = &ml->node;
from this, it's clear that both INIT_LIST_HEAD() calls
are unnecessary and can be safely removed.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Currently, DPLLs are hiding the gory details of switching parent
within set_rate, which confuses the common clock code and is wrong.
Fixed by applying the new determine_rate() and set_rate_and_parent()
functionality to any clock-ops previously using the broken approach.
This patch also removes the broken legacy code.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Expand the support of omap4 per-dpll to provide set_rate_and_parent.
This is required for proper behavior of clk_change_rate with
determine_rate support.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Similarly to OMAP3 noncore DPLL, the implementation of this DPLL clock
type is wrong. This patch adds basic functionality for determine_rate
for this clock type which will be taken into use in the patches following
later.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Currently, DPLL code hides the re-parenting within its internals, which
is wrong. This needs to be exposed to the common clock code via
determine_rate and set_rate_and_parent APIs. This patch adds support
for these, which will be taken into use in the following patches.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
DPLL4 can't be reprogrammed on OMAP3430 ES1.0 due to hardware limitation.
Currently, the code does runtime omap_rev() check to see the chip it is
being executed on, instead, change this to use clk_features flags.
This avoids need for runtime omap_rev() checks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The only place where the time is invalid is when the ACPI_CSTATE_FFH entry
method is not set. Otherwise for all the drivers, the time can be correctly
measured.
Instead of duplicating the CPUIDLE_FLAG_TIME_VALID flag in all the drivers
for all the states, just invert the logic by replacing it by the flag
CPUIDLE_FLAG_TIME_INVALID, hence we can set this flag only for the acpi idle
driver, remove the former flag from all the drivers and invert the logic with
this flag in the different governor.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Remove unused function prototype that was left by commit 149c09d3a6
("ARM: AM33xx: remove old clock data and link in new clock init code")
which removed the definition.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add btwilink device for IGEPv2 Rev. F and IGEP COM MODULE Rev. G.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
CPU logic power state is never programmed in either the initialization
or the suspend/resume logic, instead, we depend on mpuss to program this
properly. However, this leaves CPU logic power state indeterminate and
most probably in reset configuration (If bootloader or other similar
software have'nt monkeyed with the register). This can make powerstate=
RET be either programmed for CSWR (logic=ret) or OSWR(logic = OFF) and
in OSWR, there can be context loss when the code does not expect it.
To prevent all these confusions, just support clearly ON, INA, CSWR,
OFF which is the intent of the existing code by explicitly programming
logic state.
NOTE: since this is a hot path (using in cpuidle), the exit path just
programs powerstate (logic state is immaterial when powerstate is ON).
Without doing this, we end up with lockups when CPUs enter OSWR and
multiple blocks loose context, when we expect them to hit CSWR.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As we add more static dependency mapping for various errata, the logic
gets clunkier. Since it is a simple lookup and map logic, centralize the
same and provide the mapping as a simple list.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 705814b5ea ("ARM: OMAP4+: PM: Consolidate OMAP4 PM code to
re-use it for OMAP5")
Moved logic generic for OMAP5+ as part of the init routine by
introducing omap4_pm_init. However, the patch left the powerdomain
initial setup, an unused omap4430 es1.0 check and a spurious log
"Power Management for TI OMAP4." in the original code.
Remove the duplicate code which is already present in omap4_pm_init from
omap4_init_static_deps.
As part of this change, also move the u-boot version print out of the
static dependency function to the omap4_pm_init function.
Fixes: 705814b5ea ("ARM: OMAP4+: PM: Consolidate OMAP4 PM code to re-use it for OMAP5")
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These fields were added by:
commit 9574f36fb8
OMAP/serial: Add support for driving a GPIO as DTR.
but not removed by
commit 985bfd54c8
tty: serial: omap: remove some dead code
which reverted most of that commit.
Time to revert the rest.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP3 and lower SoCs don't have the ELM module so this warning
is annoying. Get rid of it.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Removing minimal support for etb/etm to favour an implementation
that is more flexible, extensible and capable of handling more
platforms.
Also removing the only client of the old driver. That code can
easily be replaced by entries for etb/etm in the device tree.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GPMC driver includes arch/arm/mach-omap2/common.h but
does not use anything on that header so it can be removed.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch remove unnecessary KERN_INFO and KERN_ERR from omap_phy_internal.c.
Add pr_fmt.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Omap4 and later have been booting in device tree only
mode for quite some time now. This initcall is no longer
needed. Note that omap3 uses a different driver omap_l3_smx,
and the initcall for that one is still needed until omap3
boots in device tree only mode.
Signed-off-by: Tony Lindgren <tony@atomide.com>
When booting omap3 in device tree mode, we're currently getting
the following errors:
omap_l3_smx omap_l3_smx.0: couldn't request debug irq
omap_l3_smx: probe of omap_l3_smx.0 failed with error -22
This is because we don't have handling in the driver for the
compatible property and instead assume platform data being
passed.
Note that this binding is already documented, and implemented
for the related omap_l3_noc driver for omap4 and later. Looks
like the binding somehow never got never implemented for this
omap_l3_smx driver though.
Let's also remove __exit_p to allow binding and unbinding
of the driver while at it.
Reported-by: Pavel Machek <pavel@ucw.cz>
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This board seems to be in use only for few automated
boot test system and has been booting in device tree
only mode for quite some time now.
So let's drop the board file for it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The 81xx support is known to be broken for quite some
time now because of missing patches. And it should be
using device tree based booting now anyways.
So let's just drop the board file for it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This code was only used by 2430sdp, 3430sdp, and n900 development
boards.
The 2430sdp is already device tree only, and all the users of the
3430sdp and n900 development boards are already booting in device
tree mode, so we can drop the legacy smc91x support.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that we have timings in the .dts files for smc91x
and 8250, we can remove the device specific checks and
just print out the bootloader timings for devices that
may not have timings in the .dts files.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As we still have some devices with GPMC timings missing from the
.dts files, let's make it a bit easier to use the bootloader
values and print them out.
Note that we now need to move the parsing of the device tree provided
configuration a bit earlier so we can use that for checking if anything
was configured.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are cases where we have multiple device instances
connected to a single GPMC chip select. For example, there
are four UARTs on the Zoom debug boards that all share a
single chip select and a GPIO interrupt.
We do have support for this already in theory, but it's broken
because we're bailing out if the chip select is already taken.
To be able to provide checks on the chip select usage, let's
add new struct gpmc_cs_data so we can start using already
registered device names for checks.
Later on we probably want to start using struct gpmc_cs_data
as a wrapper for all the GPMC chipselect related data.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A surprisingly small batch of fixes for -rc3. Suspiciously small, I'd say.
Anyway, most of this are a few defconfig updates. Some for omap to deal
with kernel binary size (moving ipv6 to module, etc). A larger one for
socfpga that refreshes with some churn, but also turns on a few options
that makes the newly-added board in my bootfarm usable for testing.
OMAP3 will also now warn when booted with legacy (non-DT) boot protocols,
hopefully encouraging those who still care about some of those platforms
to submit DT support and report bugs where needed. Nothing stops working
though, this is just to warn for future deprecation.
Beyond this, very few actual bugfixes. A PXA fix for DEBUG_LL boot hangs,
a missing terminting entry in a dt_match array on RealView a MTD fix on
OMAP with NAND.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=JasG
-----END PGP SIGNATURE-----
Merge tag 'armsoc-for-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A surprisingly small batch of fixes for -rc3. Suspiciously small, I'd
say.
Anyway, most of this are a few defconfig updates. Some for omap to
deal with kernel binary size (moving ipv6 to module, etc). A larger
one for socfpga that refreshes with some churn, but also turns on a
few options that makes the newly-added board in my bootfarm usable for
testing.
OMAP3 will also now warn when booted with legacy (non-DT) boot
protocols, hopefully encouraging those who still care about some of
those platforms to submit DT support and report bugs where needed.
Nothing stops working though, this is just to warn for future
deprecation.
Beyond this, very few actual bugfixes. A PXA fix for DEBUG_LL boot
hangs, a missing terminting entry in a dt_match array on RealView a
MTD fix on OMAP with NAND"
[ Obviously missed rc3, will make rc4 instead ;) ]
* tag 'armsoc-for-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: drop list entry for davinci
ARM: OMAP2+: Warn about deprecated legacy booting mode
ARM: omap2plus_defconfig: Fix errors with NAND BCH
ARM: multi_v7_defconfig: fix support for APQ8084
soc: versatile: Add terminating entry for realview_soc_of_match
ARM: ixp4xx: remove compilation warnings in io.h
MAINTAINERS: Add Soren as reviewer for Zynq
ARM: omap2plus_defconfig: Fix bloat caused by having ipv6 built-in
ARM: socfpga_defconfig: Update defconfig for SoCFPGA
ARM: pxa: fix hang on startup with DEBUG_LL
With legacy booting, the platform init code was taking care of
the configuring of GPIOs. With device tree based booting, things
may or may not work depending what bootloader has configured or
if the legacy platform code gets called.
Let's add support for the pwrdn and reset GPIOs to the smc91x
driver to fix the issues of smc91x not working properly when
booted in device tree mode.
And let's change n900 to use these settings as some versions
of the bootloader do not configure things properly causing
errors.
Reported-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This prevents potential division by zero errors
if GPMC fck turns out to be zero due to faulty clock
data.
Use resource managed clk_get() API.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
As per the OMAP reference manual [1], the Chip Select must be
disabled (i.e. CSVALID is 0) while configuring any of the
Chip select parameters.
[1] - 10.1.5.1 Chip-Select Base Address and Region Size Configuration
http://www.ti.com/lit/pdf/swpu177
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Although RESET state of LIMITEDADDRESS bit in GPMC_CONFIG register
is 0 (i.e. A26-A11 enabled), faulty bootloaders might accidentally
set this bit. e.g. u-boot 2014.07 with CONFIG_NOR disabled.
Explicity disable LIMITEDADDRESS bit for non NAND devices so that
they can always work.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
gpmc_cs_set_timings() returns non-zero if there was
an error while setting the GPMC timings. e.g. Timing was too
large to be accomodated with current GPMC clock frequency and available
timing range. Fail in this case, else we risk operating a NOR device
with non compliant timings.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Simplify set_gpmc_timing_reg() and always print error message
if the requested timing cannot be achieved due to a too fast
GPMC functional clock, irrespective if whether DEBUG is defined
or not. This should help us debug timing configuration issues,
which were otherwise simply not being displayed in the kernel log.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
We're moving omaps to use device tree based booting and already have
omap2, omap4, omap5, am335x and am437x booting in device tree only
mode.
Only omap3 still has legacy booting still around and we really want
to make that device tree only. So let's add a warning about deprecated
legacy booting so we get people to upgrade their boards to use device
tree based booting and find out about any remaining issues.
Note that for most boards we already have the .dts file and those can
be booted with without changing the bootloader using the appended
DTB mode.
Acked-By: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch combines the various prm_warm_reset calls under a common
API prm_reset_system, and adds the SoC specific implementation under
prm_ll_data.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds a generic API for reconfiguring the I/O chain. The implementation
will call the SoC specific function registered during init time. The SoC
specific reconfigure functions are also made static, as they don't need
to be accessed outside the PRM driver itself.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: updated for recent omap3 prcm fixes]
Signed-off-by: Tony Lindgren <tony@atomide.com>
These are not needed outside the PRM driver, so make them static and
remove the prototypes from the public header.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These are not needed outside the PRM driver, so make them static and
remove the prototypes from the public header.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These are not (and should not be) used by anybody outside the PRM
driver itself.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These should not be accessed outside driver, thus removed the APIs
from the header file and made the implementation static.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Moved the implementation from am33xx-restart.c to the prm33xx.c file to
isolate the PRM register accesses to be private for PRM driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These are not used for anything, so remove both the implementations and
header file references.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These shall not be accessed outside the CM driver. This also removes the
need for the cminst44xx.h header.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
cminst44xx.h will be removed, thus move the public APIs to cm44xx.h header.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
PRM driver now has a generic API for checking hardreset status. SoC
specific support functions are registered through the prm_ll_data.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
PRM driver now has a generic API for deasserting hardware resets. SoC
specific support functions are registered through the prm_ll_data.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
PRM driver now has a generic API for asserting hardware resets. SoC
specific support functions are registered through the prm_ll_data.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
