The TX op should return NETDEV_TX_OK or NETDEV_TX_BUSY.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TXD_W0_CIPHER field is a 1-bit field. It only acts as boolean value
to indicate if the frame must be encrypted or not.
The way rt2x00_set_field32() worked it would grab the least signifcant bit
from txdesc->cipher and use that as value. Because of that WEP 64 and TKIP
worked since they had odd-numbered values, while WEP 128 and AES were
even numbers and didn't work.
Correctly booleanize the txdecs->cipher value to allow the hardware to
encrypt the outgoing data. After this we can enable HW crypto by default again.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a panic that might occur, if the device is part of a mesh
and tries to send with a higher rate index than "0".
kernel BUG at net/mac80211/rate.c:239!
invalid opcode: 0000 [#1] SMP
[...]
Call Trace:
<IRQ> <0> ? invoke_tx_handlers+0x474/0xb57 [mac80211]
? __ieee80211_tx_prepare+0x260/0x2a8 [mac80211]
? ieee80211_master_start_xmit+0x300/0x43a [mac80211]
? __qdisc_run+0xde/0x1da
? net_tx_action+0xb4/0x102
Kernel panic - not syncing: Fatal exception in interrupt
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Should return NETDEV_TX_{OK,BUSY} instead of 0,-1 (this doesn't change
any current functionality).
Changes-licensed-under: 3-Clause-BSD
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to misunderstanding of the returned values allowed for the tx callback
of mac80211, rtl8187 was using skb's that had been freed. This problem was
triggered when the module was sujected to a rmmod/insmod cycle.
After that was fixed, the modules would not work after the rmmod/insmod cycle
until the USB device was reset.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch hopefully fixes a mac80211<->p54 interaction problem, which was
described by Larry Finger (ref: http://marc.info/?l=linux-wireless&m=123009889327707 )
I guess the warning was triggered by pending frames in the receive queue,
while we're doing a band change 5GHz.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changing mode on an interface is not allowed if IBSS is disabled for the
current channel. That restriction should only apply when switching to
the ad-hoc mode, as it was prior to "cfg80211: handle SIOCGIWMODE/SIOCSIWMODE".
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This corrects usage of AR5K_CFG_ADHOC introduced in
"ath5k: Update PCU code". Also,
the name of the indicator is changed to AR5K_CFG_IBSS to more
accurately reflect its function. This change restores
beaconing in AP and mesh modes.
Signed-off-by: Steve Brown <sbrown@cortland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch reverts "ath9k: Fix TX status reporting for retries and MCS index"
because that change ended up breaking ath9k rate control. While the
MCS index reporting to mac80211 was indeed fixed by the patch, it did
not take into account that the ath9k rate control algorithm was
updating private tables based on this index and the index comes
through the rate control API call, i.e., based on mac80211 TX status
call. In addition, it looks like the "fix" to remove +1 from TX status
'count' field was not correct based on ieee80211_tx_status()
implementation that counts the total of count values, but starting
from -1, not 0.
The TX status reporting for frames using MCS needs to be fixed
somehow, but it does not look like there is any easy fix for the ath9k
rate control algorithm, so the best option now seems to be to revert the
change and bring it back once the rate control code is cleaned up to
handle this better.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the following WARNING (caused by rix_to_ndx): "
>WARNING: at net/mac80211/rc80211_minstrel.c:69 minstrel_rate_init+0xd2/0x33a [mac80211]()
>[...]
>Call Trace:
> warn_on_slowpath+0x51/0x75
> _format_mac_addr+0x4c/0x88
> minstrel_rate_init+0xd2/0x33a [mac80211]
> print_mac+0x16/0x1b
> schedule_hrtimeout_range+0xdc/0x107
> ieee80211_add_station+0x158/0x1bd [mac80211]
> nl80211_new_station+0x1b3/0x20b [cfg80211]
The reason is that I'm experimenting with "g" only mode on a 802.11 b/g card.
Therefore rate_lowest_index returns 4 (= 6Mbit, instead of usual 0 = 1Mbit).
Since mi->r array is initialized with zeros in minstrel_alloc_sta,
rix_to_ndx has a hard time to find the 6Mbit entry and will trigged the WARNING.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes an issue with the sequence numbers of unaggregated
QoS frames, because of which the frames are handled in a different order
at the AP and resulted in MLME REPLAYFAILURE.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2500usb doesn't strip the IV/ICV data from received frames,
so we don't need to set the RX_FLAG_IV_STRIPPED flag.
We do need to set the RX_FLAG_MMIC_STRIPPED flag for all
encryption types since the MMIC has been removed from the frame.
After this patch TKIP Hardware crypto works for rt2500usb.
WEP and AES are still failing.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To be compatible with mac80211 following "mac80211: only create
default STA interface if supported", rtl8180 needs to set
NL80211_IFTYPE_STATION in interface_modes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Fabio Rossi <rossi.f@inwind.it>
Tested-by: Piter PUNK <piterpunk@unitednerds.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My first (minor) patch, hopefully this is correct.
Fix a typo in iwl-commands.h for CCK rates which needs 7 bits and not 4.
Signed-off-by: Daniel Wu <dyqith@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The queue_end() macro points to 1 position after the
queue, which means that if we want to know if queue
is at the end of the queue we should first increment
the position and then check if it is a valid entry.
This fixes a segmentation fault which only occurs when
the device has enough endpoints to provide a dedicated
endpoint for all TX queues (which likely won't happen
for rt2500usb and rt73usb, but will happen for rt2800usb).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All LM87 firmwares need a explicit termination "packet",
in oder to finish the pending transfer properly.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes two small flaws:
- restore the original TKIP IV if we altered it.
- reserve & initialize ICV with zeros.
This is actually only necessary for some obsolete p54usb firmwares.
But we don't know yet, if all devices are compatible with the new revisions.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported by Michael Jarosch <mitsch@riotmusic.de>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
0x1b is a 3945 specific command, we should print it too when debugging.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The chainmasks have to be updated before setting the channel,
since the HW reset routine uses them to set the appropriate registers.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CONFIG_ATH9K=y results in build issues if CONFIG_RFKILL=m since ath9k
does not depend on rfkill in kconfig (i.e., CONFIG_RFKILL is used to
select whether to enable rfkill in ath9k), but uses its functions if
rfkill is enabled. Enforce ath9k to be build as a module if
CONFIG_RFKILL=m to avoid this invalid configuration.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the USB ID for Thomson Speedtouch 121g to p54usb.
Signed-off-by: Michiel <michiel@ettema.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The short preamble mode was not correctly detected during TX,
rt2x00 used the rate->hw_value_short field but mac80211 is not
using this field that way.
Instead the flag IEEE80211_TX_RC_USE_SHORT_PREAMBLE should be
used to determine if the frame should be send out using
short preamble or not.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add USB ID for the Linksys WUSB200 Wireless-G Business USB Adapter to
rt73usb.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On x86_64 architecture with 4K page size and SLUB debugging enabled, stress
testing on p54usb has resulted in skb allocation failures of O(1) and extreme
page fragmentation. Reducing rx_mtu fixes this problem by reducing the size of
all receive skb allocations to be of O(0). This change does not impact
performance in any way.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since "rt2x00: Fix LED state handling", rt2x00leds_led_radio wrongly
checks that the LED type is LED_TYPE_ASSOC. This patch makes it check
for LED_TYPE_RADIO once again.
Signed-off-by: Andrew Price <andy@andrewprice.me.uk>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit e0c7317557.
This patch was wrong, as lockdep (and thus the irq state tracer)
aren't nmi safe. People are already seeing lockdep warnings due
to this.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This reverts commit 7503bfbae8.
Dieter Ries reported bootup soft-hangs and bisected it back to
this commit, and reverting this commit gave him a working system.
The commit introduces work_on_cpu() use into the cpufreq code,
but that is subtly problematic from a lock hierarchy POV: the
hotplug-cpu lock is an highlevel lock that is taken before
lowlevel locks, and in this codepath we are called with the
policy lock taken.
Dieter did not have lockdep enabled so we dont have a nice stack
trace proof for this, but using work_on_cpu() in such a lowlevel
place certainly looks wrong, so we revert the patch.
work_on_cpu() needs to be reworked to be more generally usable.
Reported-by: Dieter Ries <clip2@gmx.de>
Tested-by: Dieter Ries <clip2@gmx.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix this by reintroducing asm/smp.h include in apic.c - later on
I will fix this by removing non-smp data from smp.h
Also fix the __inquire_remote_apic() prototype/inline.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix this by reintroducing asm/smp.h include in mpparse.c - later on
I will fix this by removing non-smp data from smp.h.
Reported-by: Petr Titera <P.Titera@century.cz>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ajith Kumar noticed:
I was going through the vmalloc fault handling for x86_64 and am unclear
about the following lines in the vmalloc_fault() function.
pgd = pgd_offset(current->mm ?: &init_mm, address);
pgd_ref = pgd_offset_k(address);
Here the intention is to get the pgd corresponding to the current process
and sync it up with the pgd in init_mm(obtained from pgd_offset_k).
However, for kernel threads current->mm is NULL and hence pgd =
pgd_offset(init_mm, address) = pgd_ref which means the fault handler
returns without setting the pgd entry in the MM structure in the context
of which the kernel thread has faulted. This could lead to never-ending
faults and busy looping of kernel threads like pdflush. So, shouldn't the
pgd = pgd_offset(current->mm ?: &init_mm, address); be pgd =
pgd_offset(current->active_mm ?: &init_mm, address);
We can use active_mm unconditionally because it should be always set.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Without this, the pxa2xx-flash driver cannot be used as a module.
Reported-by: Chris Lawrence <chrisdl@netspace.net.au>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix:
arch/arm/mach-w90x900/mach-w90p910evb.c:65: error: 'W90X900_PA_UART' undeclared here (not in a function)
and silence warnings caused by inappropriate inclusion of mach/system.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some code (nfs/sunrpc) uses socket ops on kernel memory while holding
the mmap_sem, this is safe because kernel memory doesn't get paged out,
therefore we'll never actually fault, and the might_fault() annotations
will generate false positives.
Reported-by: "J. Bruce Fields" <bfields@fieldses.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If we are running DRI1 userspace, we really need to set the sarea up properly.
thanks to Richard for finding/testing this.
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit 7317d7b87e.
This has been reported (and bisected) by Alexey Zaytsev and
Kamalesh Babulal to produce annoying warnings during bootup
on both x86 and powerpc.
kernel_locked() is not a valid test in IRQ context (we update the
BKL's ->lock_depth and the preempt count separately and non-atomicalyy),
so we cannot put it into the generic preempt debugging checks which
can run in IRQ contexts too.
Reported-and-bisected-by: Alexey Zaytsev <alexey.zaytsev@gmail.com>
Reported-and-bisected-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix breakage from commit 278892736e:
i.MX Framebuffer: rename imxfb_mach_info to imx_fb_platform_data
Forgot to rename the parts in arch/arm/mach-imx/generic.c
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The LCDC controller register definitions are now part of the driver
itself, so remove them from imx-regs.h to avoid redefitions.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
snd-hda-intel driver used schedule_work() fot the delayed DMA pointer
updates, but this has several potential problems:
- it may block other eventsd works longer
- it may deadlock when probing fails and flush_scheduled_work() is
called during probe callback (as probe callback itself could be
invoked from eventd)
This patch adds an own workq for each driver instance to solve these
problems.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Intel DX58SO board works fine with model ALC883_3ST_6ch_INTEL.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This updates the cpufreq drivers in arch/powerpc so they build again
after the core cpufreq changes that broke them in commit
in835481d9bcd65720b473db6b38746a74a3964218.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
