This lets 'iw phy phy0 info' report antennas for
the radio device:
...
Available Antennas: TX 0x2 RX 0x2
Configured Antennas: TX 0x2 RX 0x2
...
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When configuring Tx vring for new connection,
WMI call to the firmware may fail. In this case, need to
clean up properly. In particular, need to call
cfg80211_del_sta() in case of AP like interface.
Perform full "disconnect" procedure for proper clean up
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Adjust driver behavior during FW boot. Proper sequence of
events after reset and FW download, is as following:
- FW prepares mailbox structure and reports IRQ "FW_READY"
- driver caches mailbox registers, marks mailbox readiness
- FW sends WMI_FW_READY event, ignore it
- FW sends WMI_READY event with some data
- driver stores relevant data marks FW is operational
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When Tx ring full is encountered with TSO,
printout of "DMA error" was wrongly printed.
In addition, in case of Tx ring full return
proper error code so that NETDEV_TX_BUSY is
returned to network stack in order not to
drop the packets and retry transmission of the
packets when ring is emptied.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some events are ignored for purpose; such events should not
be treated as "unhandled events". Replace info message
saying "unhandled" with debug one saying "ignore", to reduce
dmesg pollution
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add the hardware name, revision and update the pci_id table.
Currently there're two HW ref. designs available I'm aware of,
with 1.0.2 and 1.1 chip revisions. I've access and been using
the first one so far and this patch cover only it.
QCA9377 inherits most of the stuff (e.g. fw interfaces)
from QCA61x4 design, so the integration was pretty straightforward.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To reflect configured antenna settings in HT/VHT MCS map,
reload the HT/VHT capabilities upon antenna change.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Move HT and VHT capabiltity setup static functions to avoid
forward declaration.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HT/VHT MCS rateset should be filled only for configured chainmask
rather that max supported chainmask. Fix that by checking configured
chainmask while filling HT/VHT MCS rate map.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Removing supported chainmask fields as it can be always derived
from num_rf_chains.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For the messages from host to target, shadow copy of CE descriptors
are maintained in source ring. Before writing actual CE descriptor,
first shadow copy is filled and then it is copied to CE address space.
To optimize in download path and to reduce d-cache pressure, removing
shadow copy of CE descriptors. This will also reduce driver memory
consumption by 33KB during on device probing.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The physical address necessary to unmap DMA ('bufferp') is stored
in ath10k_skb_cb as 'paddr'. ath10k doesn't rely on the meta/transfer_id
when handling send completion (htc ep id is stored in sk_buff control
buffer). So the unused output arguments {bufferp, nbytesp and transfer_idp}
are removed from CE send completion. This change is needed before removing
the shadow copy of copy engine (CE) descriptors in follow up patch.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
CE diag window access is serialized (it has to be by design) so
there's no way to get a different send completion. so there's no
need for post completion validation.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently to avoid uncached memory access while filling up copy engine
descriptors, shadow descriptors are used. This can be optimized further
by removing shadow descriptors. To achieve that first shadow ring
dependency in ce_send is removed by creating local copy of the
descriptor on stack and make a one-shot copy into the "uncached"
descriptor.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds support for getting firmware debug stats in 10.4 fw.
Signed-off-by: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add WMI-TLV and FW API support in ath10k testmode.
Ath10k can get right wmi command format from UTF image
to communicate UTF firmware.
Signed-off-by: Alan Liu <alanliu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When card is running with DDR mode, dwmmc needs to set DDR_REG bit at
UHS_REG register.
Before this patch, dwmmc controller doesn't consider this.
If this patch is not applied, CRC or other error shoulds be occurred.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to DesignWare DoC file, CardThreshold bit should be
bit[27:16].
So it's correct to use (0xFFF << 16), not (0x1FFF << 16).
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The "host->dms->ch" pointer is NULL here so we can't use it to print the
error message.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
User visible:
- Enable per-event perf_event_attr.inherit setting by config terms, i.e.
this becomes possible:
$ perf record -e cycles/inherit/ -e instructions/no-inherit/
This affects the default, that can be changed globally using the --no-inherit
option.
This fine grained control appeared in the eBPF patchkit, but this added
flexibility may end up being useful in other scenarios (Wang Nan)
- Setup pager when printing usage and help, we have long lists of options,
better use the pager like we do with normal tooling output, i.e. when needed,
and including any error messages in the paged output (Namhyung Kim)
- Search for more options when passing args to -h, e.g.: (Arnaldo Carvalho de Melo)
$ perf report -h interface
Usage: perf report [<options>]
--gtk Use the GTK2 interface
--stdio Use the stdio interface
--tui Use the TUI interface
- Fix reading separate debuginfo files based on a build-id, problem
found on a Debian system (Dima Kogan)
- Fix endless loop when splitting kallsyms symbols per section for
handling kcore files, problem found on a s390x system (Jiri Olsa)
Infrastructure:
- Prep work for the 'perf stat record' work that will allow generating
perf.data files with counting data in addition to the sampling mode
we have now (Jiri Olsa)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wuI+
-----END PGP SIGNATURE-----
Merge tag 'perf-core-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core
Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo:
User visible changes:
- Enable per-event perf_event_attr.inherit setting by config terms, i.e.
this becomes possible:
$ perf record -e cycles/inherit/ -e instructions/no-inherit/
This affects the default, that can be changed globally using the --no-inherit
option.
This fine grained control appeared in the eBPF patchkit, but this added
flexibility may end up being useful in other scenarios. (Wang Nan)
- Setup pager when printing usage and help, we have long lists of options,
better use the pager like we do with normal tooling output, i.e. when needed,
and including any error messages in the paged output. (Namhyung Kim)
- Search for more options when passing args to -h, e.g.: (Arnaldo Carvalho de Melo)
$ perf report -h interface
Usage: perf report [<options>]
--gtk Use the GTK2 interface
--stdio Use the stdio interface
--tui Use the TUI interface
- Fix reading separate debuginfo files based on a build-id, problem
found on a Debian system. (Dima Kogan)
- Fix endless loop when splitting kallsyms symbols per section for
handling kcore files, problem found on a s390x system. (Jiri Olsa)
Infrastructure changes:
- Prep work for the 'perf stat record' work that will allow generating
perf.data files with counting data in addition to the sampling mode
we have now (Jiri Olsa)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The first generation of Open-Channel SSDs is based on NVMe. The NVMe
driver is extended with support for the LightNVM command set.
Detection is made through PCI IDs. Current supported devices are the
qemu nvme simulator and CNEX Labs Westlake SSD. The qemu nvme enables
support through vendor specific bits in the namespace identification and
the CNEX Labs Westlake SSD implements a LightNVM compatible firmware and
is detected using the same method as qemu.
After detection, vendor specific codes are used to identify the device
and enumerate supported features.
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Javier González <jg@lightnvm.io>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
This target allows an Open-Channel SSD to be exposed asas a block
device.
It implements a round-robin approach for sector allocation,
together with a greedy cost-based garbage collector.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The implementation for Open-Channel SSDs is divided into media
management and targets. This patch implements a generic media manager
for open-channel SSDs. After a media manager has been initialized,
single or multiple targets can be instantiated with the media managed as
the backend.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Open-channel SSDs are devices that share responsibilities with the host
in order to implement and maintain features that typical SSDs keep
strictly in firmware. These include (i) the Flash Translation Layer
(FTL), (ii) bad block management, and (iii) hardware units such as the
flash controller, the interface controller, and large amounts of flash
chips. In this way, Open-channels SSDs exposes direct access to their
physical flash storage, while keeping a subset of the internal features
of SSDs.
LightNVM is a specification that gives support to Open-channel SSDs
LightNVM allows the host to manage data placement, garbage collection,
and parallelism. Device specific responsibilities such as bad block
management, FTL extensions to support atomic IOs, or metadata
persistence are still handled by the device.
The implementation of LightNVM consists of two parts: core and
(multiple) targets. The core implements functionality shared across
targets. This is initialization, teardown and statistics. The targets
implement the interface that exposes physical flash to user-space
applications. Examples of such targets include key-value store,
object-store, as well as traditional block devices, which can be
application-specific.
Contributions in this patch from:
Javier Gonzalez <jg@lightnvm.io>
Dongsheng Yang <yangds.fnst@cn.fujitsu.com>
Jesper Madsen <jmad@itu.dk>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
when checking for the value of the shunt resistor.
Signed-off-by: Marc Titinger <mtitinger@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Any sysfs "show" read access from the client app will result in reading
all registers (8 with ina226). Depending on the host this can limit the
best achievable read rate.
This changeset allows for individual register accesses through regmap.
Tested with BeagleBone Black (Baylibre-ACME) and ina226.
Signed-off-by: Marc Titinger <mtitinger@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch resolves the following checkpatch warnings:
- WARNING: Missing a blank line after declarations
Signed-off-by: Kurt Kanzenbach <kurt@kmk-computers.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following checkpatch warning:
- WARNING: braces {} are not necessary for single statement blocks
Signed-off-by: Kurt Kanzenbach <kurt@kmk-computers.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch reformats some block comments in order to
match the Linux kernel coding style.
Signed-off-by: Kurt Kanzenbach <kurt@kmk-computers.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the indentation in five instances in the
ieee80211_crypt_tkip.c file.
Signed-off-by: Kurt Kanzenbach <kurt@kmk-computers.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following checkpatch error:
- ERROR: space required before the open parenthesis '('
Signed-off-by: Kurt Kanzenbach <kurt@kmk-computers.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following checkpatch error:
- ERROR: spaces required around that '='
Signed-off-by: Kurt Kanzenbach <kurt@kmk-computers.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following checkpatch error:
- ERROR: else should follow close brace '}'
Signed-off-by: Kurt Kanzenbach <kurt@kmk-computers.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following checkpatch error:
- ERROR: that open brace { should be on the previous line
Signed-off-by: Kurt Kanzenbach <kurt@kmk-computers.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This variable used only once in the beginning of the function,
it can be removed.
Signed-off-by: Ivan Safonov <insafonov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hal_data->MCSTxPowerLevelOriginalOffset[pwrGrpCnt] frequent in this function, so it replaced by the power_level_offset new variable.
Signed-off-by: Ivan Safonov <insafonov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is checkpatch fixes for hal/bb_cfg.c file: Avoid CamelCase.
Signed-off-by: Ivan Safonov <insafonov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is checkpatch fixes for hal/bb_cfg.c file:
line over 80 characters.
Signed-off-by: Ivan Safonov <insafonov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is checkpatch fixes for hal/bb_cfg.c file:
alignment should match open parenthesis.
Signed-off-by: Ivan Safonov <insafonov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is checkpatch fixes for hal/bb_cfg.c file:
unnecessary parentheses around <expr>.
Signed-off-by: Ivan Safonov <insafonov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is checkpatch fixes for hal/bb_cfg.c file:
spaces preferred around that '|'.
Signed-off-by: Ivan Safonov <insafonov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
x = x + a and x += a equivalen, but second preferably.
Signed-off-by: Ivan Safonov <insafonov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Channel numbers greater than 14 are used here, which are possible only
for the 5 GHz frequency.
Signed-off-by: Ivan Safonov <insafonov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The increment at the end of the cycle, and it can be placed in the loop header.
Signed-off-by: Ivan Safonov <insafonov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces while loop with for loop, because the initial condition and the increment clearly and briefly defined for this loop.
Signed-off-by: Ivan Safonov <insafonov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes unused MIN macro from include/rtw_security.h.
Signed-off-by: Ivan Safonov <insafonov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes unused MEM_ALIGNMENT_OFFSET and MEM_ALIGNMENT_PADDING macros
from include/basic_types.h.
Signed-off-by: Ivan Safonov <insafonov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes unused SUCCESS and FAIL macros in include/basic_types.h.
Signed-off-by: Ivan Safonov <insafonov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
abs macro is useful for determining the difference between the two integers.
Signed-off-by: Ivan Safonov <insafonov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
