Now that Wake-on-LAN support mode is fully integrated into the driver,
allow an user to query and configure Wake-on-LAN in the driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update bcmgenet_suspend() to prepare the hardware for being put into
Wake-on-LAN mode if the device can wakeup the system, and Wake-on-LAN is
enabled. Whether we resume from Wake-on-LAN or not, make sure that
bcmgenet_resume() disables the UniMAC MagicPacket matching mode and puts
the hardware in a state where it can receive all incoming packets.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet_wol_resume() will create an unbalanced clock state for the
wol_clk clock pointer since everywhere else in the code, we always call
clk_prepare_enable() and clk_disable_unprepare(). This function also
calls init_umac() which is neither correct nor necessary since
bcmgenet_resume() and bcmgenet_open() already does that.
Finally calling bcmgenet_wol_resume() in bcmgenet_open() is not correct,
since the interface would not have been able to put us in Wake-on-LAN
mode if it was not UP before.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle UMAC_IRQ_MPD_R interrupt bit in our workqueue to make sure that
we properly re-configure the GENET adapter from Wake-on-LAN.
bcmgenet_power_up() makes sure that we will not leave the UniMAC
hardware in MagicPacket matching mode, since that would prevent any
other packet from being received.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update bcmgenet_power_{up,down} to handle the case where the adapter has
been suspend respectively resumed from Wake-on-LAN using MagicPackets.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add all the required code to program the GENET hardware to enter
Wake-on-LAN mode and wake using MagicPackets with or without SecureOn
password.
This code is hooked to the build system, but is not yet referenced from
ethtool or the main bcmgenet driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Attempt to the request the Wake-on-LAN interrupt bit, and if successful,
advertise wakeup capability instead of doing this unconditionnally.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement suspend/resume callbacks in the GENET driver. This makes sure
that we de-initialize and re-initialize the hardware correctly before
entering suspend and when resuming.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a bunch of helper functions: bcmgenet_netif_start,
bcmgenet_netif_stop and bcmgenet_intr_disable to help reuse code that is
going to be necessary for suspend/resume.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor the code touching the UniMAC RX/TX enable bits since we are going
to re-use it for implementing suspend/resume.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Checking for wol_enabled in bcmgenet_close() is bogus, since no other
code places set priv->wol_enabled. Remove that as it will conflict with
the upcoming and functional Wake-on-LAN implementation.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull media fixes from Mauro Carvalho Chehab:
"A series of driver fixes:
- fix DVB-S tuning with tda1071
- fix tuner probe on af9035 when the device has a bad eeprom
- some fixes for the new si2168/2157 drivers
- one Kconfig build fix (for omap4iss)
- fixes at vpif error path
- don't lock saa7134 ioctl at driver's base core level, as it now
uses V4L2 and VB2 locking schema
- fix audio at hdpvr driver
- fix the aspect ratio at the digital timings table
- one new USB ID (at gspca_pac7302): Genius i-Look 317 webcam"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] gspca_pac7302: Add new usb-id for Genius i-Look 317
[media] tda10071: fix returned symbol rate calculation
[media] tda10071: fix spec inversion reporting
[media] tda10071: add missing DVB-S2/PSK-8 FEC AUTO
[media] tda10071: force modulation to QPSK on DVB-S
[media] hdpvr: fix two audio bugs
[media] davinci: vpif: missing unlocks on error
[media] af9035: override tuner id when bad value set into eeprom
[media] saa7134: use unlocked_ioctl instead of ioctl
[media] media: v4l2-core: v4l2-dv-timings.c: Cleaning up code wrong value used in aspect ratio
[media] si2168: firmware download fix
[media] si2157: add one missing parenthesis
[media] si2168: add one missing parenthesis
[media] staging: tighten omap4iss dependencies
Pull block fixes from Jens Axboe:
"Final block fixes for 3.16
Four small fixes that should go into 3.16, have been queued up for a
bit and delayed due to vacation and other euro duties. But here they
are. The pull request contains:
- Fix for a reported crash with shared tagging on SCSI from Christoph
- A regression fix for drbd. From Lars Ellenberg.
- Hooking up the compat ioctl for BLKZEROOUT, which requires no
translation. From Mikulas.
- A fix for a regression where we woud crash on queue exit if the
root_blkg is gone/not there. From Tejun"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: provide compat ioctl for BLKZEROOUT
blkcg: don't call into policy draining if root_blkg is already gone
drbd: fix regression 'out of mem, failed to invoke fence-peer helper'
block: don't assume last put of shared tags is for the host
Pull libata fixes from Tejun Heo:
"Late libata fixes.
The most important one is from Kevin Hao which makes sure that libata
only allocates tags inside the max tag number the controller supports.
libata always had this problem but the recent tag allocation change
and addition of support for sata_fsl which only supports queue depth
of 16 exposed the issue.
Hans de Goede agreed to become the maintainer of libahci_platform
which is under higher than usual development pressure from all the new
controllers popping up from the ARM world"
* 'for-3.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: add support for the Promise FastTrak TX8660 SATA HBA (ahci mode)
drivers/ata/pata_ep93xx.c: use signed int type for result of platform_get_irq()
libata: EH should handle AMNF error condition as a media error
libata: support the ata host which implements a queue depth less than 32
MAINTAINERS: Add Hans de Goede as ahci-platform maintainer
an x86 change too and it is a regression from 3.14. As it only affects
nested virtualization and there were other changes in this area in 3.16,
I am not nominating it for 3.15-stable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABAgAGBQJTyTTfAAoJEBvWZb6bTYbyytIQAJare/EWQmNBDK57EcJBIlJS
6MW2XnASEW+KCoUw0+u3sm9eaRXQdmJRb1Aw5zxTiUIR3ZSI8MDSQr1XxEgTAOtE
vFZjonPwlbnE8edLMhH3v/6/v9oO7bwNTDYeOE2pKPRfgPRjFmj1QUOJkvzRnRwj
kS5M4RtI+VqhdyJW8f4HaWqoRaOAISp3ZjQUJQdab3DWsf9ZpNjwLNjKzGZKNvIN
Klcpi7JH32zawUfqnAvph/7NsrBGrpFRE+j+JU9LLnD9PehuXwqZbWh01g2Anbq2
TKVrmXW+YnoD1IZsDw7r/14FaeRweV7yALA/eA9F4KfSyF2Qm9RbjVVdrUYz0CHV
aIl0cZeZM8xRCLy/ZWj+dOQ23RWelZaslHSpshKOznoRsuuvVwpx93zVtRwlw2dx
4WJ2A5gYA+ZUQ7eWjk83381JXkbRDUb3cO+NL8t9GnFctCJzT/gQHjqu15f7TJ2Q
gKhmeciKOS3xY4sQ+ti6gv8CwIFYqgdTzkxedxSgS9xpiAmw9v57V7WukXoXB6zl
AyjEAk9FFOeBZ5nXs0ObK5LKjI+MJoZ3X0bin7PCuT6dFrIA2yHvo5EgMvOcUua9
8Tu9L8sWv/JsKjuqebkKxekAKvv0CV35Q8OsLpEF6RI0eXyiXy2extk1LzUuK9cx
ZVYbN263++En/tgH2AJM
=Vdqn
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"These are mostly PPC changes for 3.16-new things. However, there is
an x86 change too and it is a regression from 3.14. As it only
affects nested virtualization and there were other changes in this
area in 3.16, I am not nominating it for 3.15-stable"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Check for nested events if there is an injectable interrupt
KVM: PPC: RTAS: Do byte swaps explicitly
KVM: PPC: Book3S PR: Fix ABIv2 on LE
KVM: PPC: Assembly functions exported to modules need _GLOBAL_TOC()
PPC: Add _GLOBAL_TOC for 32bit
KVM: PPC: BOOK3S: HV: Use base page size when comparing against slb value
KVM: PPC: Book3E: Unlock mmu_lock when setting caching atttribute
Pull s390 fixes from Martin Schwidefsky:
"A couple of last minute bug fixes for 3.16, including a fix for ptrace
to close a hole which allowed a user space program to write to the
kernel address space"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: fix restore of invalid floating-point-control
s390/zcrypt: improve device probing for zcrypt adapter cards
s390/ptrace: fix PSW mask check
s390/MSI: Use standard mask and unmask funtions
s390/3270: correct size detection with the read-partition command
s390: require mvcos facility, not tod clock steering facility
commit 4be173813e
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri Jun 6 10:22:29 2014 +0100
drm/i915: Reorder semaphore deadlock check
did the majority of the work, but it missed one crucial detail:
The check for the unkickable deadlock on this ring must come after the
check whether the ring that we are waiting on has already passed its
target seqno.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80709
Tested-by: Stefan Huber <shuber@sthu.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Calling radeon_vm_bo_find on the IB BO during CS
is illegal and can lead to an crash.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
v3: completely rewritten. We now just remember which areas
of the PT to clear and do so on the next command submission.
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=79980
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
VM sizes smaller than 1GB doesn't make much sense anyway.
v2: fix typo and grammer
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
BorisO reports that misc_register() fails often on xen. The current code
unregisters the CPU hotplug notifier in that case. If then a CPU is
offlined and onlined back again, we end up with a second timer running
on that CPU, leading to soft lockups and system hangs.
So let's leave the hotcpu notifier always registered - even if
mce_device_create failed for some cores and never unreg it so that we
can deal with the timer handling accordingly.
Reported-and-Tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: http://lkml.kernel.org/r/1403274493-1371-1-git-send-email-boris.ostrovsky@oracle.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Some drivers may be performing most of Tx/Rx
aggregation on their own (e.g. in firmware)
including AddBa/DelBa negotiations but may
otherwise require Rx reordering assistance.
The patch exports 2 new functions for establishing
Rx aggregation sessions in assumption device
driver has taken care of the necessary
negotiations.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
[fix endian bug]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers (e.g. ath10k) report A-MSDU subframes
individually with identical seqno. The A-MPDU Rx
reorder code did not account for that which made
it practically unusable with drivers using
RX_FLAG_AMSDU_MORE because it would end up
dropping a lot of frames resulting in confusion in
upper network transport layers.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
sdata can't be NULL, and key being NULL is really not possible
unless the code is modified.
The sdata check made a static analyze (klocwork) unhappy because
we would get pointer to local (sdata->local) and only then check
if sdata is non-NULL.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[remove !key check as well]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The "uptime" trace clock added in:
commit 8aacf017b0
tracing: Add "uptime" trace clock that uses jiffies
has wraparound problems when the system has been up more
than 1 hour 11 minutes and 34 seconds. It converts jiffies
to nanoseconds using:
(u64)jiffies_to_usecs(jiffy) * 1000ULL
but since jiffies_to_usecs() only returns a 32-bit value, it
truncates at 2^32 microseconds. An additional problem on 32-bit
systems is that the argument is "unsigned long", so fixing the
return value only helps until 2^32 jiffies (49.7 days on a HZ=1000
system).
Avoid these problems by using jiffies_64 as our basis, and
not converting to nanoseconds (we do convert to clock_t because
user facing API must not be dependent on internal kernel
HZ values).
Link: http://lkml.kernel.org/p/99d63c5bfe9b320a3b428d773825a37095bf6a51.1405708254.git.tony.luck@intel.com
Cc: stable@vger.kernel.org # 3.10+
Fixes: 8aacf017b0 "tracing: Add "uptime" trace clock that uses jiffies"
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
It's safer practice to use sizeof(*ptr) instead of sizeof(ptr_type) when
allocating memory in case the type changes. This also fixes the
following style of warnings from static analyzers:
CHECK: Prefer kzalloc(sizeof(*ie)...) over kzalloc(sizeof(struct inquiry_entry)...)
+ ie = kzalloc(sizeof(struct inquiry_entry), GFP_KERNEL);
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The NULL pointer access could happen when ieee80211_crypto_hw_decrypt
is called from ieee80211_rx_h_decrypt with the following condition:
1. rx->key->conf.cipher is not WEP, CCMP, TKIP or AES_CMAC
2. rx->sta is NULL
When ieee80211_crypto_hw_decrypt is called, it verifies
rx->sta->cipher_scheme and it will cause Oops if rx->sta is NULL.
This path adds an addirional rx->sta == NULL verification in
ieee80211_crypto_hw_decrypt for this case.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since "wireless-regdb: remove antenna gain" was merged in the
wireless-regdb tree, the awk script parser has been incompatible
with the 'official' regulatory database. This fixes that up.
Without this change the max EIRP is set to 0 making 802.11 devices
useless.
The fragile nature of the awk parser must be replaced, but ideas
over how to do that in the most scalable way are being reviewed.
In the meantime update the documentation for CFG80211_INTERNAL_REGDB
so folks are aware of expectations for now.
Reported-by: John Walker <john@x109.net>
Reported-by: Krishna Chaitanya <chaitanya.mgit@gmail.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The csa_active flag was added in sdata a while ago and made
IEEE80211_STA_CSA_RECEIVED redundant. The new flag is also used to
mark when CSA is ongoing on other iftypes and took over the old one as
the preferred method for checking whether we're in the middle of a
channel switch. Remove the old, redundant flag.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the teardown packet is created while the queues are
stopped, it isn't sent immediately, but rather is pending.
To be sure that when we flush the queues prior to destroying
the station we also send this packet - the tasklet handling
pending packets is invoked to flush the packets.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: ArikX Nemtsov <arik@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the AP receives actions frames destined for other peers, it may
mistakenly toggle BA-sessions from itself to a peer.
Ignore TDLS data packets as well - the AP should not handle them.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some VHT TDLS peers (Google Nexus 5) include the VHT-AID IE in their
TDLS setup request/response. Usermode passes this aid as the station
aid, causing it to fail verifiction, since this happens in the
"set_station" stage. Make an exception for the TDLS use-case.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
TDLS VHT support requires some more information elements during setup.
While these are not there, mask out the peer's VHT capabilities so that
VHT rates are not mistakenly used.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Set for completeness mostly, currently unused in the code.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the HT capabilities and HT operation information elements to TDLS
setup packets where appropriate.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We can only be a station for TDLS connections. Also fix a bug where
a delayed work could be left scheduled if the station interface was
brought down during TDLS setup.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When TDLS QoS is supported by the the peer and the local card, add
the WMM parameter IE to the setup-confirm frame. Take the QoS settings
from the current AP, or if unsupported, use the default values from
the specification. This behavior is mandated by IEEE802.11-2012 section
10.22.4.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If QoS is supported by the card, add an appropriate IE to TDLS setup-
request and setup-response frames.
Consolidate the setting of the WMM info IE across mac80211.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When sending setup-failure frames, set the capability field to zero, as
mandated by the specification (IEEE802.11-2012 8.5.13).
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Most setup-specific information elements are not to be added when a
setup frame is sent with an error status code.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When building TDLS setup frames, use the IE order mandates in the
specification, splitting extra IEs coming from usermode.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add all information elements for TDLS discovery and setup in the same
function.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The patch "8f02e6b mac80211: make sure TDLS peer STA exists during
setup" broke TDLS error paths where the STA doesn't exist when sending
the error.
Fix it by only testing for STA existence during a non-error flow.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Infer the TDLS initiator and track it in mac80211 via a STA flag. This
avoids breaking old userspace that doesn't pass it via nl80211 APIs.
The only case where userspace will need to pass the initiator is when the
STA is removed due to unreachability before a teardown packet is sent.
Support for unreachability was only recently added to wpa_supplicant, so
it won't be a problem in practice.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a VLAN interface (on top of batX) is removed and
re-added within a short timeframe TT does not have enough
time to properly cleanup. This creates an internal TT state
mismatch as the newly created softif_vlan will be
initialized from scratch with a TT client count of zero
(even if TT entries for this VLAN still exist). The
resulting TT messages are bogus due to the counter / tt
client listing mismatch, thus creating inconsistencies on
every node in the network
To fix this issue destroy_vlan() has to not free the VLAN
object immediately but it has to be kept alive until all the
TT entries for this VLAN have been removed. destroy_vlan()
still removes the sysfs folder so that the user has the
feeling that everything went fine.
If the same VLAN is re-added before the old object is free'd,
then the latter is resurrected and re-used.
Implement such behaviour by increasing the reference counter
of a softif_vlan object every time a new local TT entry for
such VLAN is created and remove the object from the list
only when all the TT entries have been destroyed.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Add new AUX ROC command that is intended for HS2.0 purposes.
It is used to send ANQP requests on a specific channel.
This command requests the firmware to trigger a time event
and remain on a certain channel for a given duration.
Triggering the time event is done by using the Aux
Framework in the firmware, and makes use of the Aux station
(similarly to scan).
Signed-off-by: Ariej Marjieh <ariej.marjieh@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Enabling the Aux queue and mapping it to FIFO 5.
Defining the Aux queue for the Aux station.
Signed-off-by: Ariej Marjieh <ariej.marjieh@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add iwl_mvm_ref_sync() calls (with new ref types) to
flows that might access the device directly.
These calls make sure the device is out of d0i3,
and the bus is available for direct access.
Since some of these functions are reentrant, convert
the refs_bitmap to a ref counter, so multiple refs
of the same type could be taken concurrently.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
