This patch changes the fetch_pte function in the AMD IOMMU
driver to support dynamic mapping levels.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Instead of a panic on an comletion wait loop failure, try to
recover from that event from resetting the command buffer.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
To prevent the driver from doing recursive command buffer
resets, just panic when that recursion happens.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
On an ILLEGAL_COMMAND_ERROR the IOMMU stops executing
further commands. This patch changes the code to handle this
case better by resetting the command buffer in the IOMMU.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch factors parts of the command buffer
initialization code into a seperate function which can be
used to reset the command buffer later.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This function flushes all DTE entries on one IOMMU for all
devices behind this IOMMU. This is required for command
buffer resetting later.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The amd_iommu_pd_table is indexed by protection domain
number and not by device id. So this check is broken and
must be removed.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch replaces the "AMD IOMMU" printk strings with the
official name for the hardware: "AMD-Vi".
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch removes some left-overs which where put into the code to
simplify merging code which also depends on changes in other trees.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch introduces a function to flush all domain tlbs
for on one given IOMMU. This is required later to reset the
command buffer on one IOMMU.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch adds code to dump the command which caused an
ILLEGAL_COMMAND_ERROR raised by the IOMMU hardware.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch adds code to dump the content of the device table
entry which caused an ILLEGAL_DEV_TABLE_ENTRY error from the
IOMMU hardware.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Add a keyctl to install a process's session keyring onto its parent. This
replaces the parent's session keyring. Because the COW credential code does
not permit one process to change another process's credentials directly, the
change is deferred until userspace next starts executing again. Normally this
will be after a wait*() syscall.
To support this, three new security hooks have been provided:
cred_alloc_blank() to allocate unset security creds, cred_transfer() to fill in
the blank security creds and key_session_to_parent() - which asks the LSM if
the process may replace its parent's session keyring.
The replacement may only happen if the process has the same ownership details
as its parent, and the process has LINK permission on the session keyring, and
the session keyring is owned by the process, and the LSM permits it.
Note that this requires alteration to each architecture's notify_resume path.
This has been done for all arches barring blackfin, m68k* and xtensa, all of
which need assembly alteration to support TIF_NOTIFY_RESUME. This allows the
replacement to be performed at the point the parent process resumes userspace
execution.
This allows the userspace AFS pioctl emulation to fully emulate newpag() and
the VIOCSETTOK and VIOCSETTOK2 pioctls, all of which require the ability to
alter the parent process's PAG membership. However, since kAFS doesn't use
PAGs per se, but rather dumps the keys into the session keyring, the session
keyring of the parent must be replaced if, for example, VIOCSETTOK is passed
the newpag flag.
This can be tested with the following program:
#include <stdio.h>
#include <stdlib.h>
#include <keyutils.h>
#define KEYCTL_SESSION_TO_PARENT 18
#define OSERROR(X, S) do { if ((long)(X) == -1) { perror(S); exit(1); } } while(0)
int main(int argc, char **argv)
{
key_serial_t keyring, key;
long ret;
keyring = keyctl_join_session_keyring(argv[1]);
OSERROR(keyring, "keyctl_join_session_keyring");
key = add_key("user", "a", "b", 1, keyring);
OSERROR(key, "add_key");
ret = keyctl(KEYCTL_SESSION_TO_PARENT);
OSERROR(ret, "KEYCTL_SESSION_TO_PARENT");
return 0;
}
Compiled and linked with -lkeyutils, you should see something like:
[dhowells@andromeda ~]$ keyctl show
Session Keyring
-3 --alswrv 4043 4043 keyring: _ses
355907932 --alswrv 4043 -1 \_ keyring: _uid.4043
[dhowells@andromeda ~]$ /tmp/newpag
[dhowells@andromeda ~]$ keyctl show
Session Keyring
-3 --alswrv 4043 4043 keyring: _ses
1055658746 --alswrv 4043 4043 \_ user: a
[dhowells@andromeda ~]$ /tmp/newpag hello
[dhowells@andromeda ~]$ keyctl show
Session Keyring
-3 --alswrv 4043 4043 keyring: hello
340417692 --alswrv 4043 4043 \_ user: a
Where the test program creates a new session keyring, sticks a user key named
'a' into it and then installs it on its parent.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
This block is allocated with alloc_bootmem() and scanned by kmemleak but
the kernel direct mapping may no longer exist. This patch tells kmemleak
to ignore this memory hole. The dma32_bootmem_ptr in
dma32_reserve_bootmem() is also ignored.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Make it possible to access the all-register-setting/getting MSR
functions via the MSR driver. This is implemented as an ioctl() on
the standard MSR device node.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Borislav Petkov <petkovbb@gmail.com>
For some reason, the _safe MSR functions returned -EFAULT, not -EIO.
However, the only user which cares about the return code as anything
other than a boolean is the MSR driver, which wants -EIO. Change it
to -EIO across the board.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
fbd8b1819e turns off the bit for
/proc/cpuinfo. However, a proper/full fix would be to additionally
turn off the bit in the CPUID output so that future callers get
correct CPU features info.
Do that by basically reversing what the BIOS wrongfully does at boot.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <1251705011-18636-3-git-send-email-petkovbb@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Switch them to native_{rd,wr}msr_safe_regs and remove
pv_cpu_ops.read_msr_amd.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
LKML-Reference: <1251705011-18636-2-git-send-email-petkovbb@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
native_{rdmsr,wrmsr}_safe_regs are two new interfaces which allow
presetting of a subset of eight x86 GPRs before executing the rd/wrmsr
instructions. This is needed at least on AMD K8 for accessing an erratum
workaround MSR.
Originally based on an idea by H. Peter Anvin.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
LKML-Reference: <1251705011-18636-1-git-send-email-petkovbb@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Merge reason: the SFI (Simple Firmware Interface) feature in the ACPI
tree needs this cleanup, pull it into the APIC branch as
well so that there's no interactions.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some IO-APIC routines are ACPI specific now, but need to
be exposed when CONFIG_ACPI=n for the benefit of SFI.
Remove #ifdef ACPI around these routines:
io_apic_get_unique_id(int ioapic, int apic_id);
io_apic_get_version(int ioapic);
io_apic_get_redir_entries(int ioapic);
Move these routines from ACPI-specific boot.c to io_apic.c:
uniq_ioapic_id(u8 id)
mp_find_ioapic()
mp_find_ioapic_pin()
mp_register_ioapic()
Also, since uniq_ioapic_id() is now no longer static,
re-name it to io_apic_unique_id() for consistency
with the other public io_apic routines.
For simplicity, do not #ifdef the resulting code ACPI || SFI,
thought that could be done in the future if it is important
to optimize the !ACPI !SFI IO-APIC x86 kernel for size.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: x86@kernel.org
Convert the syscalls event tracing code to use NR_syscalls, instead of
FTRACE_SYSCALL_MAX. NR_syscalls is standard accross most arches, and
reduces code confusion/complexity.
Signed-off-by: Jason Baron <jbaron@redhat.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Jiaying Zhang <jiayingz@google.com>
Cc: Martin Bligh <mbligh@google.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Josh Stone <jistone@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anwin <hpa@zytor.com>
Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
LKML-Reference: <9b4f1a84ecae57cc6599412772efa36f0d2b815b.1251146513.git.jbaron@redhat.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Express the available number of syscalls in a standard way by defining
NR_syscalls.
The common way to define it is to place its definition in asm/unistd.h
However, the number of syscalls is defined using __NR_syscall_max in
x86-64 after building a dynamic header file "asm-offsets.h"
The source file that generates this header, asm-offsets-64.c includes
unistd.h, then if we want to express NR_syscalls from __NR_syscall_max
in unistd.h only after generating the dynamic header file, we need a
watchguard.
If unistd.h is included from asm-offsets-64.c, then we are generating
asm-offset.h which defines __NR_syscall_max. At this time, we don't
want to (we can't) define NR_syscalls, then we do nothing.
Otherwise we define NR_syscalls because we know asm-offsets.h has
been generated.
Signed-off-by: Jason Baron <jbaron@redhat.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Jiaying Zhang <jiayingz@google.com>
Cc: Martin Bligh <mbligh@google.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Josh Stone <jistone@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anwin <hpa@zytor.com>
Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
LKML-Reference: <20090826160910.GB2658@redhat.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
As far as I see there is no external poking of mp_lapic_addr in
this procedure which could lead to unpredited changes and
require local storage unit for it. Lets use it plain forward.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <20090826171324.GC4548@lenovo>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2.6.31-rc7 does not boot on vSMP systems:
[ 8.501108] CPU31: Thermal monitoring enabled (TM1)
[ 8.501127] CPU 31 MCA banks SHD:2 SHD:3 SHD:5 SHD:6 SHD:8
[ 8.650254] CPU31: Intel(R) Xeon(R) CPU E5540 @ 2.53GHz stepping 04
[ 8.710324] Brought up 32 CPUs
[ 8.713916] Total of 32 processors activated (162314.96 BogoMIPS).
[ 8.721489] ERROR: parent span is not a superset of domain->span
[ 8.727686] ERROR: domain->groups does not contain CPU0
[ 8.733091] ERROR: groups don't span domain->span
[ 8.737975] ERROR: domain->cpu_power not set
[ 8.742416]
Ravikiran Thirumalai bisected it to:
| commit 2759c3287d
| x86: don't call read_apic_id if !cpu_has_apic
The problem is that on vSMP systems the CPUID derived
initial-APICIDs are overlapping - so we need to fall
back on hard_smp_processor_id() which reads the local
APIC.
Both come from the hardware (influenced by firmware
though) so it's a tough call which one to trust.
Doing the quirk expresses the vSMP property properly
and also does not affect other systems, so we go for
this solution instead of a revert.
Reported-and-Tested-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Shai Fultheim <shai@scalex86.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <4A944D3C.5030100@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
alloc_bootmem() already panics on allocation failure. There is
no need to check the result.
Also there is a way to unbind global variable from its body and
use it as a parameter which allow us to simplify
ioapic_init_mappings as well -- "for" cycle already uses
nr_ioapics as a conditional variable and there is no need to
check if ioapic_setup_resources was returning NULL again.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <20090824175551.493629148@openvz.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We already have APIC_DEFAULT_PHYS_BASE so just to be
consistent.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
LKML-Reference: <20090824175550.927946757@openvz.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This converts the syscall_enter/exit tracepoints into TRACE_EVENTs, so
you can have generic ftrace events that capture all system calls with
arguments and return values. These generic events are also renamed to
sys_enter/exit, so they're more closely aligned to the specific
sys_enter_foo events.
Signed-off-by: Josh Stone <jistone@redhat.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Jiaying Zhang <jiayingz@google.com>
Cc: Martin Bligh <mbligh@google.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
LKML-Reference: <1251150194-1713-5-git-send-email-jistone@redhat.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
It's not strictly correct for the tracepoint reg/unreg callbacks to
occur when a client is hooking up, because the actual tracepoint may not
be present yet. This happens to be fine for syscall, since that's in
the core kernel, but it would cause problems for tracepoints defined in
a module that hasn't been loaded yet. It also means the reg/unreg has
to be EXPORTed for any modules to use the tracepoint (as in SystemTap).
This patch removes DECLARE_TRACE_WITH_CALLBACK, and instead introduces
DEFINE_TRACE_FN which stores the callbacks in struct tracepoint. The
callbacks are used now when the active state of the tracepoint changes
in set_tracepoint & disable_tracepoint.
This also introduces TRACE_EVENT_FN, so ftrace events can also provide
registration callbacks if needed.
Signed-off-by: Josh Stone <jistone@redhat.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Jiaying Zhang <jiayingz@google.com>
Cc: Martin Bligh <mbligh@google.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
LKML-Reference: <1251150194-1713-4-git-send-email-jistone@redhat.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
s/HAVE_FTRACE_SYSCALLS/HAVE_SYSCALL_TRACEPOINTS/g
s/TIF_SYSCALL_FTRACE/TIF_SYSCALL_TRACEPOINT/g
The syscall enter/exit tracing is no longer specific to just ftrace, so
they now have names that reflect their tie to tracepoints instead.
Signed-off-by: Josh Stone <jistone@redhat.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Jiaying Zhang <jiayingz@google.com>
Cc: Martin Bligh <mbligh@google.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
LKML-Reference: <1251150194-1713-2-git-send-email-jistone@redhat.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
clockevent: Prevent dead lock on clockevents_lock
timers: Drop write permission on /proc/timer_list
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix build with older binutils and consolidate linker script
x86: Fix an incorrect argument of reserve_bootmem()
x86: add vmlinux.lds to targets in arch/x86/boot/compressed/Makefile
xen: rearrange things to fix stackprotector
x86: make sure load_percpu_segment has no stackprotector
i386: Fix section mismatches for init code with !HOTPLUG_CPU
x86, pat: Allow ISA memory range uncacheable mapping requests
For the x86_model to be greater than 6 or less than 12 is
logically always true.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
binutils prior to 2.17 can't deal with the currently possible
situation of a new segment following the per-CPU segment, but
that new segment being empty - objcopy misplaces the .bss (and
perhaps also the .brk) sections outside of any segment.
However, the current ordering of sections really just appears
to be the effect of cumulative unrelated changes; re-ordering
things allows to easily guarantee that the segment following
the per-CPU one is non-empty, and at once eliminates the need
for the bogus data.init2 segment.
Once touching this code, also use the various data section
helper macros from include/asm-generic/vmlinux.lds.h.
-v2: fix !SMP builds.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: <sam@ravnborg.org>
LKML-Reference: <4A94085D02000078000119A5@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some of the NOPs tables aren't used on 64-bits, quite some code and
data is needed post-init for module loading only, and a couple of
functions aren't used outside that file (i.e. can be static, and don't
need to be exported).
The change to __INITDATA/__INITRODATA is needed to avoid an assembler
warning.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
LKML-Reference: <4A8BC8A00200007800010823@vpn.id2.novell.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The default_send_IPI_mask_logical() function uses the "flat" APIC mode
to send an IPI to a set of CPU's at once, but if that set happens to be
empty, some older local APIC's will apparently be rather unhappy. So
just warn if a caller gives us an empty mask, and ignore it.
This fixes a regression in 2.6.30.x, due to commit 4595f9620 ("x86:
change flush_tlb_others to take a const struct cpumask"), documented
here:
http://bugzilla.kernel.org/show_bug.cgi?id=13933
which causes a silent lock-up. It only seems to happen on PPro, P2, P3
and Athlon XP cores. Most developers sadly (or not so sadly, if you're
a developer..) have more modern CPU's. Also, on x86-64 we don't use the
flat APIC mode, so it would never trigger there even if the APIC didn't
like sending an empty IPI mask.
Reported-by: Pavel Vilim <wylda@volny.cz>
Reported-and-tested-by: Thomas Björnell <thomas.bjornell@gmail.com>
Reported-and-tested-by: Martin Rogge <marogge@onlinehome.de>
Cc: Mike Travis <travis@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
load_percpu_segment() is used to set up the per-cpu segment registers,
which are also used for -fstack-protector. Make sure that the
load_percpu_segment() function doesn't have stackprotector enabled.
[ Impact: allow percpu setup before calling stack-protected functions ]
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Currently clockevents_notify() is called with interrupts enabled at
some places and interrupts disabled at some other places.
This results in a deadlock in this scenario.
cpu A holds clockevents_lock in clockevents_notify() with irqs enabled
cpu B waits for clockevents_lock in clockevents_notify() with irqs disabled
cpu C doing set_mtrr() which will try to rendezvous of all the cpus.
This will result in C and A come to the rendezvous point and waiting
for B. B is stuck forever waiting for the spinlock and thus not
reaching the rendezvous point.
Fix the clockevents code so that clockevents_lock is taken with
interrupts disabled and thus avoid the above deadlock.
Also call lapic_timer_propagate_broadcast() on the destination cpu so
that we avoid calling smp_call_function() in the clockevents notifier
chain.
This issue left us wondering if we need to change the MTRR rendezvous
logic to use stop machine logic (instead of smp_call_function) or add
a check in spinlock debug code to see if there are other spinlocks
which gets taken under both interrupts enabled/disabled conditions.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: "Pallipadi Venkatesh" <venkatesh.pallipadi@intel.com>
Cc: "Brown Len" <len.brown@intel.com>
LKML-Reference: <1250544899.2709.210.camel@sbs-t61.sc.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: use the right flag for get_vm_area()
percpu, sparc64: fix sparse possible cpu map handling
init: set nr_cpu_ids before setup_per_cpu_areas()
Commit 0e83815be7 changed the
section the initial_code variable gets allocated in, in an
attempt to address a section conflict warning. This, however
created a new section conflict when building without
HOTPLUG_CPU. The apparently only (reasonable) way to address
this is to always use __REFDATA.
Once at it, also fix a second section mismatch when not using
HOTPLUG_CPU.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Robert Richter <robert.richter@amd.com>
LKML-Reference: <4A8AE7CD020000780001054B@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
