Define a flag for struct efx_rx_buffer and efx_rx_packet() that
indicates packet length must be read from the prefix. If this
is set, read the length in __efx_rx_packet() (when the prefix
should have arrived in cache).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Add a counter for TX merged completion events.
This is implemented in the common TX path, because the NIC event
handlers only know how many descriptors were completed, not how many
packets.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
EF10 uses an entirely different RX prefix format from Falcon-arch.
Extend struct efx_nic_type to describe this.
[bwh: Also replace the magic numbers used for the Falcon-arch RX prefix]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
efx_reset_up() calls efx_nic_type::reconfigure_mac once directly,
then again through efx_start_all() -> efx_start_port() ->
efx->type->reconfigure_mac().
This first call is also made too early to work properly on EF10.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The Huntington MC will reject all MCDI requests after an MC reboot until it sees
one with the NOT_EPOCH flag clear. This flag is set by default for all requests,
and then cleared on the first request after we detect that an MC reboot has
occurred.
The old MCDI_STATUS_DELAY_COUNT gave a timeout of 10ms, which was not long enough
for the driver to detect that a reboot had occurred based on the warm boot count
while calling efx_mcdi_poll_reboot() from the loop in efx_mcdi_ev_death().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Also, since we handle all DMA errors in the same way, merge
RESET_TYPE_(RX|TX)_DESC_FETCH into RESET_TYPE_DMA_ERROR.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Various hardware statistics that are available for Siena are
unavailable or meaningless for Falcon. Huntington adds further to the
NIC-type-specific statistics, as it has different MAC blocks from
Falcon/Siena.
All NIC types still provide most statistics by DMA, and use
little-endian byte order.
Therefore:
1. Add some general utility functions for reporting hardware statistics,
efx_nic_describe_stats() and efx_nic_update_stats().
2. Add an efx_nic_type::describe_stats operation to get the number and
names of statistics, implemented using efx_nic_describe_stats()
3. Change efx_nic_type::update_stats to store the core statistics
(struct rtnl_link_stats64) or full statistics (array of u64) in a
caller-provided buffer. Use efx_nic_update_stats() to aid in the
implementation.
4. Rename struct efx_ethtool_stat to struct efx_sw_stat_desc and
EFX_ETHTOOL_NUM_STATS to EFX_ETHTOOL_SW_STAT_COUNT.
5. Remove efx_nic::mac_stats and struct efx_mac_stats.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Merge the per-NIC-type MTD probe selection and struct efx_mtd_ops into
struct efx_nic_type. Move the implementations into the appropriate
source files.
Several NVRAM functions are now only called from MTD operations which
are now implemented in the same file (falcon.c or mcdi.c). There is no
need for them to be extern, or to be defined at all if CONFIG_SFC_MTD
is not enabled, so move them into the #ifdef CONFIG_SFC_MTD sections
in those files.
Most of the SPI-related definitions are also only used in falcon.c,
so move them there. Put the remainder of spi.h into nic.h (which
previously included it).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Steven (cc-ed) noticed an imbalance in semaphore put/get for
82573-based NICs. Don't we need something like the following
(untested) patch?
Signed-off-by: Steven La <sla@riverbed.com>
Acked-by: Arthur Kepner <akepner@riverbed.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the firmware to address the thermal notification issue
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support is provided only for combined channels. When SR-IOV is not
enabled, BE3 supports upto 16 channels and Lancer-R/SH-R support upto
32 channels.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Move be_cmd_if_create() above queue create routines to allow
TXQ creation (that requires if_handle) to be clubbed with TX-CQ creation.
2) Consolidate all queue create routines into be_setup_queues()
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the IF_CREATE FW cmd is issued only *after* MCCQ is created as
it was coded to only use MCCQ. By fixing this, cmd_if_create() can be
called before MCCQ is created and the same routine for VF provisioning
can be called after.
This allows for consolidating all the queue create routines by moving
the be_cmd_if_create() call above all queue create calls in be_setup().
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) use be_resources{} struct to query/store HW resource limits
2) The HW queue/resource limits for BE2/BE3 chips are mostly called out
in driver as constants. Code to handle this is scattered across various
places in be_setup(). Consolidate this code into BEx_get_resources().
For Lancer-R, Skyhawk-R, these limits are queried from FW.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Parse PCIe descriptor for max-VFs supported by HW
2) Cleanup NIC descriptor parsing in get_func/profile_config() routines
3) Use common struct definitions for v0 and v1 versions of GET_FUNC_CONFIG
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EQ_CREATEv2 explicitly returns the msix-index associated with a EQ.
For SH-R this is needed if EQs need to be deleted and re-created without
resetting a function.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Adapter and driver supports only CEE dcbnl ops. Only GET callbacks
within dcbnl ops are supported currently.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Adapter sends Asynchronous Event Notifications to the driver when
there are changes in the switch or adapter DCBX configuration.
AEN handler updates the driver DCBX parameters.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Populate driver data structures with local, operational, and peer
DCB parameters.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Query adapter DCB capabilities and populate local data structures
with relevant information.
o Add QLCNIC_DCB to Kconfig for enabling/disabling DCB.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
1. Refactoring and cleanup in preparation for new hardware support.
2. Some bug fixes for firmware completion handling. (They're not known
to cause real problems, otherwise I'd be submitting these for net and
stable.)
3. Update to the firmware protocol (MCDI) definitions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/iwlwifi/pcie/trans.c
include/linux/inetdevice.h
The inetdevice.h conflict involves moving the IPV4_DEVCONF values
into a UAPI header, overlapping additions of some new entries.
The iwlwifi conflict is a context overlap.
Signed-off-by: David S. Miller <davem@davemloft.net>
The macb driver only handle PHY description through platform_data
(macb_platform_data).
Thus, when using dt you cannot define phy properties like phy address or
phy irq pin.
This patch makes use of the of_mdiobus_register to add support for
phy device definition using dt.
A fallback to the autoscan procedure is added in case there is no phy
devices defined in dt.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
make the Freescale ethernet driver get, prepare and enable the FEC clock
during probe(); disable and unprepare the clock upon remove(), put is
done by the devm approach; hold a reference to the clock over the period
of use.
clock lookup is non-fatal as not all platforms provide clock specs in
their device tree; failure to enable specified clocks is fatal.
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 720a43efd3
(drivers:net: Remove unnecessary OOM messages after netdev_alloc_skb)
there is a build warning:
drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c: In function 'tx_skb_align_workaround':
drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c:586:26: warning: unused variable 'fep'
Fix it.
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed when the cpsw driver is built as module.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit fba875591 ("disable TX in be_close()") disabled TX in be_close()
to protect be_xmit() from touching freed up queues in the AER recovery
flow. But, TX must be disabled *before* cleaning up TX completions in
the close() path, not after. This allows be_tx_compl_clean() to free up
all TX-req skbs that were notified to the HW.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some reason, my PCIe RTL8111E onboard NIC on a GA-Z68X-UD3H-B3
motherboard reads as FFs when reading from MMIO with a block size
larger than 7. Therefore change to reading blocks of four bytes.
Ben Hutchings noted that the buffer is large enough to hold all
registers, so now all registers are read.
Signed-off-by: Peter Wu <lekensteyn@gmail.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we use struct efx_mtd to represent a physical NVRAM device
and struct efx_mtd_partition to represent a partition on that device.
But this only really makes sense for Falcon, as we don't know or care
whether MC-managed NVRAM partitions are on one or more physical
devices. It complicates iteration and provides little benefit.
Therefore:
- Replace the pointer to efx_mtd in mtd_info::priv with a pointer to efx_nic
- Move the falcon_spi_device pointer into the union in struct efx_mtd_partition
- Move the device name to efx_mtd_partition::dev_type_name
- Move the efx_mtd_ops pointer to efx_nic::mtd_ops
- Make efx_nic::mtd_list a list of partitions
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
On Falcon we implement MAC filtering requested by the stack using the
MAC wrapper's single unicast filter and multicast hash filter. Siena
is very similar, though MAC configuration is mediated by the MC.
Since MCDI operations may sleep, reconfiguration is deferred from
ndo_set_rx_mode to a work item. However, it still updates the private
variables describing the filter state synchronously. Contrary to
comments, the later use of these variables is not protected using the
address lock, resulting in race conditions.
Move the state update to a new function
efx_farch_filter_sync_rx_mode() and make the Falcon-arch MAC
configuration functions call that, so that its use is consistently
serialised by the mac_lock.
Invert and rename the promiscuous flag to the more accurate
unicast_filter, and comment that both this and multicast_hash are
not used on EF10.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
MAC filters inserted on request from the stack (ndo_set_rx_mode)
should allow manual steering but not removal. Currently we have a
special case for Siena's all-multicast and all-unicast MAC filters,
but on EF10 we need to allow for steering of precise MAC filters as
well.
The EFX_FILTER_FLAG_RX_STACK flag changes the behaviour of replacement
and removal requests:
- Replacement *of* a filter with this flag never clears the flag but
does change steering and saved priority
- Replacement *by* a filter with this flag only sets the flag but does
not change steering
- Removal with priority < EFX_FILTER_PRI_REQUIRED really resets RX
steering and saved priority
This could support precise MAC filtering on Siena in future.
As a side-benefit, the default MAC filters are hidden from ethtool
until they are steered.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Move the special case for removal of default filters from
efx_farch_filter_table_clear_entry() into a wrapper function,
efx_farch_filter_table_remove(). Move the existence and priority
checks into the latter and use it where appropriate.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Aside from accelerated RFS, there is almost nothing that can be shared
between the filter table implementations for the Falcon architecture
and EF10.
Move the few shared functions into efx.c and rx.c and the rest into
farch.c. Introduce efx_nic_type operations for the implementation and
inline wrapper functions that call these.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Currently every call to efx_farch_filter_table_clear_entry() is
shortly followed by a conditional reset of the table limits. The new
limits (0) are not pushed to hardware until the next filter insertion.
Move both the reset and the hardware reconfiguration into
efx_farch_filter_table_clear_entry(), and add an explanatory comment.
Also, make consistent use of the term 'search limit' for the maximum
number of probes the NIC must make when searching for a filter of a
particular type.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Move the common state from struct efx_filter_state into struct efx_nic.
Rename struct efx_filter_state to efx_farch_filter_state and change
the type of efx_nic::filter_state to void *.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>