Current handler acknowledges interrupt in both the irq handler
and the irq thread. This clears interrupts that come between the
irq handler and the irq thread. This patch reorganizes irq
acknowledgment to the irq handler and changes the irq thread to
also check for completed requests by comparing request timestamp
and hardware completion timestamp. Upon error or timeout event,
hardware status is dumped to aid irq related fault isolation.
CRs-Fixed: 1044128
Change-Id: I085c2c2ec55106a8fb196f3ef1cfcb42e2b2507c
Signed-off-by: Alan Kwong <akwong@codeaurora.org>
Add support to read charger and skin temp hot and
too hot temperature threshold values programmed
during initialization.
Change-Id: I46dca1f606b5414bf7a032c18c9684ba2e53cf28
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
Signed-off-by: Nicholas Troast <ntroast@codeaurora.org>
The final temperature values for PMI die temperature and
charger temperature are in units of millidegC. Update
the slope factor value to avoid losing resolution
accuracy while values are reported in units of millidegC.
Change-Id: Iec4aa730fa97133af0c0fb9d47557738ef6f45a0
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
Currently there are no channel specific properties associated
with the RRADC channels. The existing channel nodes specify
a logical channel number that is used by the client when
requesting the RRADC channel read. This can instead be obtained
from the channel list specified within the driver. Therefore
remove the channel nodes.
Change-Id: I4da81a576b88285cedb0a1c7fd49ccd526d25012
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
A check is needed to ensure the LSB and MSB are coherent
when reading the result registers for the RRADC channels.
The driver performs another round of read request and
compares the result registers to ensure the data read
back is coherent.
Since there are no channel specific properties remove
the dependency to add the channel nodes in the device
tree and instead statically register the channels within
the driver.
Update the scaling functions to report in the units
desired for the final scaled value based on the channel.
The resistance channel reports the units for batt_id
in ohms, the voltage channels such as DCIN, USBIN report
the value in units of microvolts, the current channels
in units of microamps and the temperature channels
such as thermistors are reported in units of millidegC.
Change-Id: I56e6bff28be2cc23f00622d5c37e42564c51a72f
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
Change the default IPC logging messages to help log analysis instead of
having to change log mask levels and having to re-run the test cases.
Currently single log is used to gather all the driver messages. Split
these into dedicated tx/rx payload log, client ioctl/power state log and
generic driver state log.
Also only dump 32 bytes of the tx/rx payload.
Change-Id: I8dee2f8aa0a6882ec1c320669f165e7cb94bb5f1
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Don't modify the ref count variable clk count inside the runtime callbacks.
Doing so could result in a case where the driver might end up calling a put
twice on the runtime object. The resulting imbalance will leave the runtime
state for the device in a bad state.
Change-Id: I34989768811b23762c4afe3e33e229ffa3f1db17
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
As part of the resource voting, both the resource_vote and unvote
functions call the toggle_wakeup_interrupt() function which toggles the
state of the wakeup irq unconditionally. This can cause issues in adverse
scenarios. Instead split this out into exclusive enable and disable wakeup
interrupt functions to be called during the resource unvote and vote
respectively. Also don't make resource votes in the wakeup isr, the
wakeup isr injects a pre-determined byte into the tty flip buffer and
doesn't access the core or setup any transactions and hence doesn't need
to vote for resources.
The driver has registered for the noirq system suspend/resume callbacks.
When executing these callbacks, don't rely on the runtime framework to
check the device's current runtime state before deciding whether to allow
system suspend or not as the runtime framework is disabled at this point.
Instead rely on the power state that the driver maintains internally.
Change-Id: I0e5d6b8a8a69efc2d9c65dc1edc85f13cbc94fc3
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Modify the sleep set GPIO bias for UART_3. This will help lower leakage
once the usecase for UART_3 has ended.
Change-Id: I50d918197a4cd0b503dff78e7d4ba89518c1d1c2
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Modify the sleep set GPIO bias for I2C_5. This will help lower leakage once
the usecase for I2C_5 has ended.
Change-Id: I41e9012210ce9a5f4fbeb4236365c0fa2db08625
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
change to use SW AEAD and HMAC algorithms with ARMv8 crypto
extensions by default on msmcobalt, as they have better performances
than algorithms using HW crypto engines.
Change-Id: If68b68374bfabcdef7ecbf245b72b12c4734f811
Signed-off-by: Zhen Kong <zkong@codeaurora.org>
Adding support for dynamic FPS adjustment in mdss 3.x. Adjustment
is based on front/back porch changes.
CRs-Fixed: 1047142
Change-Id: Ie4ab889a7d64ba8e33675ee22bf7b808d9ba0a3f
Signed-off-by: Benjamin Chan <bkchan@codeaurora.org>
For USB 2.0 there is a requirement to not to flush the
USB endpoints after the pipes are disconnected. Otherwise
this can result into NOC errors. Make a change to modify the
disconnect sequence as below.
1) USB driver first disable the pipes
2) New API is provided from IPA to disable the endpoint.
3) As part of disable, make sure pipes are empty and reset
the pipes.
4) USB resets its BAM and flushes the ep.
5) USB then disconnects both IPA and USB pipes.
Change-Id: I917f025678e6abb03058d5be4ec42d9e6d76835f
CRs-Fixed: 1038623
Acked-by: Chaitanya Pratapa <cpratapa@qti.qualcomm.com>
Acked-by: Mohammed Javid <mjavid@qti.qualcomm.com>
Signed-off-by: Utkarsh Saxena <usaxena@codeaurora.org>
During IPA driver processing context delete, a delete to
the referenced header is being done. The header deletion
will also commit the changes to H/W which includes the
processing context commit. This resulted into committing
an invalid process context as it is still in the processing
context list, but points to deleted header.
The fix is to not commit the changes when deleting the header
but only when deleting the processing context.
Change-Id: I9d3c5eec717da0b072144a1027e4582e73aaa6d9
CRs-fixed: 1044710
Signed-off-by: Ghanim Fodi <gfodi@codeaurora.org>
The array index value when setting/getting the channels
of proxy is incorrect as the channel count begins from two.
Fix by setting the correct index offset.
Change-Id: I3ab9858daf6dcdbce762946cbdebeb96eaad764a
Signed-off-by: Shiv Maliyappanahalli <smaliyap@codeaurora.org>
Goodix GT915 driver was provided by vendor and cherry-picked into
our project, it need to be placed to right location.
Change-Id: Idf191144354426233eca41727a41e26ddbf92f95
Signed-off-by: Bingzhe Cai <bingzhec@codeaurora.org>
Signed-off-by: Pan Fang <fangpan@codeaurora.org>
Registers for page 0x50 in the wcd934x audio codec are currently
not defined. These registers control WCD DSP register configuration
and setup. Add these register definitions so that codec driver can
read/write these registers.
CRs-Fixed: 1049012
Change-Id: If1162c09de8d4d7c330a97a1f133f6d46ce2fd74
Signed-off-by: Bhalchandra Gajare <gajare@codeaurora.org>
This module provides two APIs which are used to control a boolean
sysfs entry deploy. The irq balancer's blacklist in user space will be
controlled by this sysfs entry.
CRs-Fixed: 1013201
Change-Id: Ie6ec7211c64f3c4f53b9f590e5bcf5fa1937d594
Signed-off-by: Runmin Wang <runminw@codeaurora.org>
Remove dmesg about irq redistributor since it fills up
the console with every hotplug of the cpus. The information
about redistributor is already disclosed in the dmesg during
bootup.
CRs-Fixed: 1048941
Change-Id: I5ddb2036ab3df4715382368c144365d578ce4bb8
Signed-off-by: Runmin Wang <runminw@codeaurora.org>
One of the CPE sessions uses EC(Echo cancellation) PP(Ping-Pong)
path on WCD9335 that is connected to CPE (Codec Processing Engine)
hardware. Configure EC PP path for CPE functionality. This
requires WCD9335 codec to be out of digital core power collapse
without turning on MCLK(Master clock).
CRs-fixed: 1022917
Change-Id: I68200b12fcb316bf36f7c3af2734a094f972da9c
Signed-off-by: Sudheer Papothi <spapothi@codeaurora.org>
Signed-off-by: Vidyakumar Athota <vathota@codeaurora.org>
