Since the new multi-queue capability depends on a new firmware API,
we can already add some code for it. If the new API is present, a
new opmode ops struct is used that handles the new rx_rss method.
For now, only restructure the RX handling to distinguish between
the two. Future patches will convert the new infrastructure to
actually use the new RX descriptor layout.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of relying on a hard-coded constant of a maximum of 64 API and
capability bits, add a new enum value after the others that will then
always track the number of used bits in the API/capabilities. We thus
no longer need to maintain the maximum number, and on 32-bit platforms
even (currently) reduce the number of bits kept in memory.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no need to have negative threshold temperatures, so make
them unsigned to avoid signedness warnings in debugfs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Using an int* instead of u32* as the kstrtou32() output argument
obviously results in signedness warnings, change that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is a tweak which has been shown to improve performance when
moving away from the AP while working in 80Mhz.
When RS decides to go down to 80MHz SISO MCS0 instead switch to 20MHz MCS4.
Go back to 80MHz MCS1 if RS can sustain 20MHz MCS5.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As the 3165 device uses the same firmware as 7265-D and currently
all 7000 series (including 3160/3165) use the same API versions
remove IWL3165_UCODE_API_OK and _MIN. We might have to put them
back if firmware support ever splits, but in that case might also
have to add a different MODULE_FIRMWARE statement.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
success_ratio is actually 128 * SR in percentage while
IWL_MVM_RS_SR_NO_DECREASE is 85%. Fix this by using RS_PERCENT().
This bug caused the if branch to be always executed. This in turn
led to always selecting a rate, following a column switch, in which
the expected throughput would exceed the best expected current throughput.
In some scenarios where the success ratio isn't >85% such a rate
could be too aggressive leading us to avoid the new column.
This has the potential of causing sub optimal performance.
Reported-by: Moshe Harel <moshe.harel@intel.com>
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This message isn't very useful and creates clutter.
Remove it.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware has always treated these two bits to mean that
powersave is enabled when POWER_SAVE_ENA is set and CAM is
clear; it doesn't use them in any non-combined way.
Therefore, it's pointless to send it two bits, and the API
should be cleaned up. Prepare the driver by removing the CAM
bit and using only POWER_SAVE_ENA to indicate whether PS is
enabled or not.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When enabling a queue, the default SSN is 0.
Allow determining what that SSN should be, if required. This
can happen, for example, if a queue gets reconfigured.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
"DQA" is shorthand for "dynamic queue allocation", with the
idea of allocating queues per-RA/TID on-demand rather than
using shared queues statically allocated per vif. The goal
of this is to enable future features (like GO PM) and to
improve performance measurements of TX traffic.
When RA/TID streams can't be neatly sorted into different AC
queues, DQA allows sharing queues for the same RA. This means
that DQA allows different ACs may reach the same HW queue.
Update the code to allow such queue sharing by having a mapping
between the HW queue and the mac80211 queues using it (as this
could be more than one queue).
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As the transport will decide how many queues (and MSI-X vectors)
to allocate, add a field to indicate that to the op-mode so it
can size/allocate its own data structures appropriately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Upcoming hardware will have the ability to do L3 hashing for RSS,
directing data packets (and perhaps some associated metadata and
management notifications) to different MSI-X vectors.
In this case, it makes no sense to go through the full RX dispatch
since it's already known that only a subset of the possibilities
can come in, requiring a new receive method. In addition this must
know which queue the packet was received on.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Treat PHY RX specially, since it's actually pretty frequent,
doesn't need all the notication etc. code, and will have a
different handler in future hardware.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Return a proper error when wrong parameters are passed to debugfs
tof_range_request.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The command needs to have the AP interfaces BSSID (which corresponds
to its address).
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Make some input formats more natural, e.g. bandwidth and periods
are more natural in decimal than in hexadecimal.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Commit ce7929186a ("iwlwifi: mvm: add basic Time of Flight (802.11mc
FTM) support") created drivers/net/wireless/iwlwifi/mvm/tof.h with a
broken header guard:
#ifndef __tof
#define __tof_h__
...
#endif /* __tof_h__ */
Use __tof_h__ in the first line.
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Commit "iwlwifi: mvm: don't ask beacons when AP vif and no
assoc sta" directly called iwl_mvm_mac_ctxt_cmd_ap() to update the
MAC context when adding/removing a station. However, this ignores
the case that the vif is actually a P2P GO.
Fix this by calling iwl_mvm_mac_ctxt_changed() that handles P2P GO
case as well.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For the ADD_STA command, when the flag for aggregation
disabling is set, there is a bitmap indicated what TIDs
are disabling aggregations and what aren't. Currently, by
default, all TIDs allow for aggregations since the value
we begin with is 0.
Change this default value to 0xffff so all TIDs don't
allow aggregations until explicitly turned on.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Tracing, if disabled at runtime, has very low overhead with
great returns on debugging. It therefore makes sense to have
it enabled by default (if the kernel enables EVENT_TRACING).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The ilw@linux.intel.com address is being phased out, replace
it with the new address.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The formula used in D0i3 should also be used in D3, instead of
the hardcoded value.
Additionally, the formula is actually wrong - if the calculation
yields 0 then 1 should be used instead of disabling entirely.
Also need to add 1 since the firmware needs 3 to skip 2, etc.
To make all this clearer, centralize the calculation into a
single function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is a workaround to an OTP bug. In Series 8000 1x1, the OTP
0xA052 defines 2x2 antenna configuration. This workaround overrides
the decision based on HW id and MIMO disabled bit which is correct
in the OTP and set to disabled.
Signed-off-by: Moshe Harel <moshe.harel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move the DTS measurement command and notification from short
command header to the new PHY command group for firmware
supporting the extended command headers.
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* fix signedness in beacon statistics;
* deinline some functions to reduce size when device tracing is enabled;
* filter beacons out in AP mode when no stations are associated;
* deprecate firmwares version -12;
* fix a runtime PM vs. legacy suspend race;
* one-liner fix for a ToF bug;
* clean-ups in the rx code;
* small debugging improvement;
* fix WoWLAN with new firmware versions;
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XkqB
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2015-09-21' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* some debugfs improvements;
* fix signedness in beacon statistics;
* deinline some functions to reduce size when device tracing is enabled;
* filter beacons out in AP mode when no stations are associated;
* deprecate firmwares version -12;
* fix a runtime PM vs. legacy suspend race;
* one-liner fix for a ToF bug;
* clean-ups in the rx code;
* small debugging improvement;
* fix WoWLAN with new firmware versions;
In order to verify d0i3 flow, add debug print to indicate
d0i3 exit was completed (right after tx was re-enabled),
along with the wakeup reasons.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Recent fw version added assert to make sure wowlan configuration
is configured only when a station is connected.
Change the driver behavior to pass this configuration only
if we indeed have ap station id (i.e. connected).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The RX API is currently mixed up into the general fw-api.h
file, but we're going to need to extend it significantly in
the future, so move it to its own file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Remove some unused values from the RX API; these were used
with older firmware API that didn't have the RX energy API,
support for which was removed a long time ago.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since the driver can never configure the data here, this field
will always be reported as 0 by the firmware. Even if this was
not the case, however, it wouldn't matter since the extra data
would be added beyond the end of the phy_info structure we use
in the driver, so wouldn't harm anything in this code either.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This message is useless - it's in the good case that always
happens so enabling it doesn't really help. Just remove it.
There are other ways to debug this (e.g. tracing) so there's
no need to add a message in the bad case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
It's possible for an AP interface to be UP but not actually
operating (i.e. not beaconing etc.) - in this case it can't
actually do ToF, so check for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This flag is set in all supported firmwares.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
This flag is set in all supported firmwares.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
All the supported firmwares have this flag set.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
All the supported firmwares use the new API.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
All the supported firwmares support the new API.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Current kernel support only one fw name with theoretically only one
fw version located in “firmware/htc_[9271|7010].fw”. Which is ok so far we
have only one fw version (1.3). After we realised new fw 1.4, we faced
compatibility problem which was decided to solve by firmware name and
location:
- new firmware is located now in
firmware/ath9k_htc/htc_[9271|7010]-1.4.0.fw
- old version 1.3 should be on old place, so old kernel have no issues
with it.
- new kernels including this patch should be able to try different
supported (min..max) fw version.
- new kernel should be able to support old fw location too. At least for
now.
At same time this patch will add new module option which should allow user
to play with development fw version without replacing stable one. If user
will set “ath9k_htc use_dev_fw=1” module will try to find
firmware/ath9k_htc/htc_[9271|7010]-1.dev.0.fw first and if it fails, use
stable version: for example...1.4.0.fw.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Memory placement in sch_dsmark is silly : Better place mask/value
in the same cache line.
Also, we can embed small arrays in the first cache line and
remove a potential cache miss.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: bcmgenet: Interrupt coalescing
This patch series adds support for interrupt coalescing for GENET
adapters.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the ethtool rx-frames coalescing parameter which allows
defining the number of RX interrupts per frames received. The RDMA
engine supports a configurable timeout with a resolution of
approximately 8.192 us.
We can no longer enable the BDONE/PDONE interrupts as those would
fire for each packet/buffer received, which would defeat the MBDONE
interrupt purpose. The MBDONE interrupt is guaranteed to correspond to a
PDONE/BDONE interrupt when the threshold is set to 1.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configuring the ethtool tx-frames property, which translates into N
packets before a TX interrupt is the simplest configuration scheme
because it requires no locking neither at the softare nor hardware
level, and is completely indepedent from the link speed. Since ethtool
does not allow per-tx queue coalescing parameters, we apply the same
setting to any transmit queue.
We can no longer enable the BDONE/PDONE interrupts as those would fire
for each packet/buffer received, which would defeat the MBDONE interrupt
purpose. The MBDONE interrupt is guaranteed to correspond to a
PDONE/BDONE interrupt when the threshold is set to 1, but offers
interrupt coalescing when the value is > 1.
Since the HW is configured to generate an interrupt when the ring
becomes emtpy, we have to deny any timeout/timer settings coming from
user-space to indicate we can only generate an interrupt very <N>
packets.
While we are at it, fix the DMA_INTR_THRESHOLD_MASK value which was off
by one bit (0xff vs. 0x1ff).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove not defined MAC_CR_GMII_EN_ bit from MAC_CR.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create lan78xx_get_mdix_status() and lan78xx_set_mdix_status() for MDIX control.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove phy defines in lan78xx.h and use defines in include/linux/microchipphy.h.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
