On certain PMICs, PMIC peripheral drivers like haptics need to
read MISC peripheral register. Add support for clients to read
it by using qpnp_misc_read_reg().
Change-Id: Id5dfd9e440a8861b56572dab50839d1583535882
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
QPNP_MISC driver provides support to read the registers or
support functions required on certain PMICs. Enable it.
Change-Id: Ib496506e60dc94dec1b2292bf0e6fd01583e2f75
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
QPNP_MISC driver provides support to read the registers or
support functions required on certain PMICs. Enable it.
Change-Id: If2a056feca4cc982d8840f6a2159a0788d08cd26
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
qpnp-misc driver supports some miscellaneous stuff which is
needed on certain PMICs. Change it to a platform driver similar
to other PMIC peripheral drivers.
Change-Id: I3f60bbe88616db82b568cc528f076368afd105ca
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
App type is required to send the calibration
for the modules in a topology that would
be selected for ULLPP. For this, expose
a mixer control. App type will be sent
if the ULLPP is used for NOIRQ.
CRs-Fixed: 2009687
Change-Id: I7c8349d5827dffe32c0db35262d54cb7c1dba1a9
Signed-off-by: Alexy Joseph <alexyj@codeaurora.org>
Some FS devices report maxpacket size as 4 for their BULK EPs
which is incorrect as per USB specification. This results in
ep_config command to controller timing out and enumeration fails.
As minimum maxpacket size for FS is 8, override the same for such
devices.
CRs-fixed: 1002876
Change-Id: I70c2210b4eb93f557eef306fcbc11308b7b33e07
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
The wlan firmware is configuring the clk and voltage regulator
for hardware power on and hardware reset sequence.
The icnss platform driver is configuring this clk and regulators
to avoid invalid access to copy engine register during the wlan
recovery.
As platform driver is not configuring this regulator to power on
or reset the WLAN hardware, So no need to define the voltage
regulators are the required properties for the ICNSS platform driver.
Define vdd-0.8-cx-mx as an optional voltage regulator for
the icnss platform driver.
CRs-Fixed: 2014965
Change-Id: I74a1445522997ba4e7a52da5a29e9afb57ad12df
Signed-off-by: Sarada Prasanna Garnayak <sgarna@codeaurora.org>
As GPIO 54 has already been connected to an external
pull up resistor, config it to no pull to save power
consumption.
CRs-Fixed: 2015121
Change-Id: Id13588be53b8756e4d9792035bcc6adfbaa8c3f7
Signed-off-by: xiaonian <xiaonian@codeaurora.org>
Add backend user count checking to protect the index
boundary.
Change-Id: Ic1b61d1f7130252cc54da0b16553858714988dbd
CRs-Fixed: 2009216
Signed-off-by: Walter Yang <yandongy@codeaurora.org>
Mark AIF4 MAD TX as ignore suspend so that MAD path
will not power down during suspend mode.
CRs-Fixed: 2003858
Change-Id: Iae55e2778edcdd8efa6ae13b746795d8a1594a41
Signed-off-by: Walter Yang <yandongy@codeaurora.org>
HIFI headphone path is not present in sdm660 qrd board.
So there is no need to add these two hph_en nodes under tasha node.
These two nodes get initialized by msm_cdc_pinctrl driver and make
gpio24/25 as output low, which causes some power leakage.
Remove these two hph_en nodes for sdm660 qrd.
Change-Id: I527ce45296cd3b168bea67804e0909f668f74221
CRs-Fixed: 2011375
Signed-off-by: Walter Yang <yandongy@codeaurora.org>
