[ Upstream commit 355b98553789b646ed97ad801a619ff898471b92 ]
net_hash_mix() currently uses kernel address of a struct net,
and is used in many places that could be used to reveal this
address to a patient attacker, thus defeating KASLR, for
the typical case (initial net namespace, &init_net is
not dynamically allocated)
I believe the original implementation tried to avoid spending
too many cycles in this function, but security comes first.
Also provide entropy regardless of CONFIG_NET_NS.
Fixes: 0b4419162a ("netns: introduce the net_hash_mix "salt" for hashes")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Amit Klein <aksecurity@gmail.com>
Reported-by: Benny Pinkas <benny@pinkas.net>
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit aecfde23108b8e637d9f5c5e523b24fb97035dc3 ]
RFC8257 §3.5 explicitly states that "A DCTCP sender MUST react to
loss episodes in the same way as conventional TCP".
Currently, Linux DCTCP performs no cwnd reduction when losses
are encountered. Optionally, the dctcp_clamp_alpha_on_loss resets
alpha to its maximal value if a RTO happens. This behavior
is sub-optimal for at least two reasons: i) it ignores losses
triggering fast retransmissions; and ii) it causes unnecessary large
cwnd reduction in the future if the loss was isolated as it resets
the historical term of DCTCP's alpha EWMA to its maximal value (i.e.,
denoting a total congestion). The second reason has an especially
noticeable effect when using DCTCP in high BDP environments, where
alpha normally stays at low values.
This patch replace the clamping of alpha by setting ssthresh to
half of cwnd for both fast retransmissions and RTOs, at most once
per RTT. Consequently, the dctcp_clamp_alpha_on_loss module parameter
has been removed.
The table below shows experimental results where we measured the
drop probability of a PIE AQM (not applying ECN marks) at a
bottleneck in the presence of a single TCP flow with either the
alpha-clamping option enabled or the cwnd halving proposed by this
patch. Results using reno or cubic are given for comparison.
| Link | RTT | Drop
TCP CC | speed | base+AQM | probability
==================|=========|==========|============
CUBIC | 40Mbps | 7+20ms | 0.21%
RENO | | | 0.19%
DCTCP-CLAMP-ALPHA | | | 25.80%
DCTCP-HALVE-CWND | | | 0.22%
------------------|---------|----------|------------
CUBIC | 100Mbps | 7+20ms | 0.03%
RENO | | | 0.02%
DCTCP-CLAMP-ALPHA | | | 23.30%
DCTCP-HALVE-CWND | | | 0.04%
------------------|---------|----------|------------
CUBIC | 800Mbps | 1+1ms | 0.04%
RENO | | | 0.05%
DCTCP-CLAMP-ALPHA | | | 18.70%
DCTCP-HALVE-CWND | | | 0.06%
We see that, without halving its cwnd for all source of losses,
DCTCP drives the AQM to large drop probabilities in order to keep
the queue length under control (i.e., it repeatedly faces RTOs).
Instead, if DCTCP reacts to all source of losses, it can then be
controlled by the AQM using similar drop levels than cubic or reno.
Signed-off-by: Koen De Schepper <koen.de_schepper@nokia-bell-labs.com>
Signed-off-by: Olivier Tilmans <olivier.tilmans@nokia-bell-labs.com>
Cc: Bob Briscoe <research@bobbriscoe.net>
Cc: Lawrence Brakmo <brakmo@fb.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Daniel Borkmann <borkmann@iogearbox.net>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Andrew Shewmaker <agshew@gmail.com>
Cc: Glenn Judd <glenn.judd@morganstanley.com>
Acked-by: Florian Westphal <fw@strlen.de>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 09279e615c81ce55e04835970601ae286e3facbe ]
Syzbot report a kernel-infoleak:
BUG: KMSAN: kernel-infoleak in _copy_to_user+0x16b/0x1f0 lib/usercopy.c:32
Call Trace:
_copy_to_user+0x16b/0x1f0 lib/usercopy.c:32
copy_to_user include/linux/uaccess.h:174 [inline]
sctp_getsockopt_peer_addrs net/sctp/socket.c:5911 [inline]
sctp_getsockopt+0x1668e/0x17f70 net/sctp/socket.c:7562
...
Uninit was stored to memory at:
sctp_transport_init net/sctp/transport.c:61 [inline]
sctp_transport_new+0x16d/0x9a0 net/sctp/transport.c:115
sctp_assoc_add_peer+0x532/0x1f70 net/sctp/associola.c:637
sctp_process_param net/sctp/sm_make_chunk.c:2548 [inline]
sctp_process_init+0x1a1b/0x3ed0 net/sctp/sm_make_chunk.c:2361
...
Bytes 8-15 of 16 are uninitialized
It was caused by that th _pad field (the 8-15 bytes) of a v4 addr (saved in
struct sockaddr_in) wasn't initialized, but directly copied to user memory
in sctp_getsockopt_peer_addrs().
So fix it by calling memset(addr->v4.sin_zero, 0, 8) to initialize _pad of
sockaddr_in before copying it to user memory in sctp_v4_addr_to_user(), as
sctp_v6_addr_to_user() does.
Reported-by: syzbot+86b5c7c236a22616a72f@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Tested-by: Alexander Potapenko <glider@google.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cb66ddd156203daefb8d71158036b27b0e2caf63 ]
When it is to cleanup net namespace, rds_tcp_exit_net() will call
rds_tcp_kill_sock(), if t_sock is NULL, it will not call
rds_conn_destroy(), rds_conn_path_destroy() and rds_tcp_conn_free() to free
connection, and the worker cp_conn_w is not stopped, afterwards the net is freed in
net_drop_ns(); While cp_conn_w rds_connect_worker() will call rds_tcp_conn_path_connect()
and reference 'net' which has already been freed.
In rds_tcp_conn_path_connect(), rds_tcp_set_callbacks() will set t_sock = sock before
sock->ops->connect, but if connect() is failed, it will call
rds_tcp_restore_callbacks() and set t_sock = NULL, if connect is always
failed, rds_connect_worker() will try to reconnect all the time, so
rds_tcp_kill_sock() will never to cancel worker cp_conn_w and free the
connections.
Therefore, the condition !tc->t_sock is not needed if it is going to do
cleanup_net->rds_tcp_exit_net->rds_tcp_kill_sock, because tc->t_sock is always
NULL, and there is on other path to cancel cp_conn_w and free
connection. So this patch is to fix this.
rds_tcp_kill_sock():
...
if (net != c_net || !tc->t_sock)
...
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
==================================================================
BUG: KASAN: use-after-free in inet_create+0xbcc/0xd28
net/ipv4/af_inet.c:340
Read of size 4 at addr ffff8003496a4684 by task kworker/u8:4/3721
CPU: 3 PID: 3721 Comm: kworker/u8:4 Not tainted 5.1.0 #11
Hardware name: linux,dummy-virt (DT)
Workqueue: krdsd rds_connect_worker
Call trace:
dump_backtrace+0x0/0x3c0 arch/arm64/kernel/time.c:53
show_stack+0x28/0x38 arch/arm64/kernel/traps.c:152
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x120/0x188 lib/dump_stack.c:113
print_address_description+0x68/0x278 mm/kasan/report.c:253
kasan_report_error mm/kasan/report.c:351 [inline]
kasan_report+0x21c/0x348 mm/kasan/report.c:409
__asan_report_load4_noabort+0x30/0x40 mm/kasan/report.c:429
inet_create+0xbcc/0xd28 net/ipv4/af_inet.c:340
__sock_create+0x4f8/0x770 net/socket.c:1276
sock_create_kern+0x50/0x68 net/socket.c:1322
rds_tcp_conn_path_connect+0x2b4/0x690 net/rds/tcp_connect.c:114
rds_connect_worker+0x108/0x1d0 net/rds/threads.c:175
process_one_work+0x6e8/0x1700 kernel/workqueue.c:2153
worker_thread+0x3b0/0xdd0 kernel/workqueue.c:2296
kthread+0x2f0/0x378 kernel/kthread.c:255
ret_from_fork+0x10/0x18 arch/arm64/kernel/entry.S:1117
Allocated by task 687:
save_stack mm/kasan/kasan.c:448 [inline]
set_track mm/kasan/kasan.c:460 [inline]
kasan_kmalloc+0xd4/0x180 mm/kasan/kasan.c:553
kasan_slab_alloc+0x14/0x20 mm/kasan/kasan.c:490
slab_post_alloc_hook mm/slab.h:444 [inline]
slab_alloc_node mm/slub.c:2705 [inline]
slab_alloc mm/slub.c:2713 [inline]
kmem_cache_alloc+0x14c/0x388 mm/slub.c:2718
kmem_cache_zalloc include/linux/slab.h:697 [inline]
net_alloc net/core/net_namespace.c:384 [inline]
copy_net_ns+0xc4/0x2d0 net/core/net_namespace.c:424
create_new_namespaces+0x300/0x658 kernel/nsproxy.c:107
unshare_nsproxy_namespaces+0xa0/0x198 kernel/nsproxy.c:206
ksys_unshare+0x340/0x628 kernel/fork.c:2577
__do_sys_unshare kernel/fork.c:2645 [inline]
__se_sys_unshare kernel/fork.c:2643 [inline]
__arm64_sys_unshare+0x38/0x58 kernel/fork.c:2643
__invoke_syscall arch/arm64/kernel/syscall.c:35 [inline]
invoke_syscall arch/arm64/kernel/syscall.c:47 [inline]
el0_svc_common+0x168/0x390 arch/arm64/kernel/syscall.c:83
el0_svc_handler+0x60/0xd0 arch/arm64/kernel/syscall.c:129
el0_svc+0x8/0xc arch/arm64/kernel/entry.S:960
Freed by task 264:
save_stack mm/kasan/kasan.c:448 [inline]
set_track mm/kasan/kasan.c:460 [inline]
__kasan_slab_free+0x114/0x220 mm/kasan/kasan.c:521
kasan_slab_free+0x10/0x18 mm/kasan/kasan.c:528
slab_free_hook mm/slub.c:1370 [inline]
slab_free_freelist_hook mm/slub.c:1397 [inline]
slab_free mm/slub.c:2952 [inline]
kmem_cache_free+0xb8/0x3a8 mm/slub.c:2968
net_free net/core/net_namespace.c:400 [inline]
net_drop_ns.part.6+0x78/0x90 net/core/net_namespace.c:407
net_drop_ns net/core/net_namespace.c:406 [inline]
cleanup_net+0x53c/0x6d8 net/core/net_namespace.c:569
process_one_work+0x6e8/0x1700 kernel/workqueue.c:2153
worker_thread+0x3b0/0xdd0 kernel/workqueue.c:2296
kthread+0x2f0/0x378 kernel/kthread.c:255
ret_from_fork+0x10/0x18 arch/arm64/kernel/entry.S:1117
The buggy address belongs to the object at ffff8003496a3f80
which belongs to the cache net_namespace of size 7872
The buggy address is located 1796 bytes inside of
7872-byte region [ffff8003496a3f80, ffff8003496a5e40)
The buggy address belongs to the page:
page:ffff7e000d25a800 count:1 mapcount:0 mapping:ffff80036ce4b000
index:0x0 compound_mapcount: 0
flags: 0xffffe0000008100(slab|head)
raw: 0ffffe0000008100 dead000000000100 dead000000000200 ffff80036ce4b000
raw: 0000000000000000 0000000080040004 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8003496a4580: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8003496a4600: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff8003496a4680: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff8003496a4700: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8003496a4780: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
Fixes: 467fa15356ac("RDS-TCP: Support multiple RDS-TCP listen endpoints, one per netns.")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ef0efcd3bd3fd0589732b67fb586ffd3c8705806 ]
At the beginning of ip6_fragment func, the prevhdr pointer is
obtained in the ip6_find_1stfragopt func.
However, all the pointers pointing into skb header may change
when calling skb_checksum_help func with
skb->ip_summed = CHECKSUM_PARTIAL condition.
The prevhdr pointe will be dangling if it is not reloaded after
calling __skb_linearize func in skb_checksum_help func.
Here, I add a variable, nexthdr_offset, to evaluate the offset,
which does not changes even after calling __skb_linearize func.
Fixes: 405c92f7a5 ("ipv6: add defensive check for CHECKSUM_PARTIAL skbs in ip_fragment")
Signed-off-by: Junwei Hu <hujunwei4@huawei.com>
Reported-by: Wenhao Zhang <zhangwenhao8@huawei.com>
Reported-by: syzbot+e8ce541d095e486074fc@syzkaller.appspotmail.com
Reviewed-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c0cca7c847e6e019d67b7d793efbbe3b947d004 upstream.
By default, the kernel will automatically load the module of any line
dicipline that is asked for. As this sometimes isn't the safest thing
to do, provide a sysctl to disable this feature.
By default, we set this to 'y' as that is the historical way that Linux
has worked, and we do not want to break working systems. But in the
future, perhaps this can default to 'n' to prevent this functionality.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7084edc3f6d67750f50d4183134c4fb5712a5c8 upstream.
The n_r3964 line discipline driver was written in a different time, when
SMP machines were rare, and users were trusted to do the right thing.
Since then, the world has moved on but not this code, it has stayed
rooted in the past with its lovely hand-crafted list structures and
loads of "interesting" race conditions all over the place.
After attempting to clean up most of the issues, I just gave up and am
now marking the driver as BROKEN so that hopefully someone who has this
hardware will show up out of the woodwork (I know you are out there!)
and will help with debugging a raft of changes that I had laying around
for the code, but was too afraid to commit as odds are they would break
things.
Many thanks to Jann and Linus for pointing out the initial problems in
this codebase, as well as many reviews of my attempts to fix the issues.
It was a case of whack-a-mole, and as you can see, the mole won.
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[ Upstream commit 5f074f3e192f10c9fade898b9b3b8812e3d83342 ]
A recent optimization in Clang (r355672) lowers comparisons of the
return value of memcmp against zero to comparisons of the return value
of bcmp against zero. This helps some platforms that implement bcmp
more efficiently than memcmp. glibc simply aliases bcmp to memcmp, but
an optimized implementation is in the works.
This results in linkage failures for all targets with Clang due to the
undefined symbol. For now, just implement bcmp as a tailcail to memcmp
to unbreak the build. This routine can be further optimized in the
future.
Other ideas discussed:
* A weak alias was discussed, but breaks for architectures that define
their own implementations of memcmp since aliases to declarations are
not permitted (only definitions). Arch-specific memcmp
implementations typically declare memcmp in C headers, but implement
them in assembly.
* -ffreestanding also is used sporadically throughout the kernel.
* -fno-builtin-bcmp doesn't work when doing LTO.
Link: https://bugs.llvm.org/show_bug.cgi?id=41035
Link: https://code.woboq.org/userspace/glibc/string/memcmp.c.html#bcmp
Link: 8e16d73346
Link: https://github.com/ClangBuiltLinux/linux/issues/416
Link: http://lkml.kernel.org/r/20190313211335.165605-1-ndesaulniers@google.com
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Reported-by: Adhemerval Zanella <adhemerval.zanella@linaro.org>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Suggested-by: James Y Knight <jyknight@google.com>
Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Nathan Chancellor <natechancellor@gmail.com>
Suggested-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ac3e233d29f7f77f28243af0132057d378d3ea58 upstream.
GNU linker's -z common-page-size's default value is based on the target
architecture. arch/x86/entry/vdso/Makefile sets it to the architecture
default, which is implicit and redundant. Drop it.
Fixes: 2aae950b21 ("x86_64: Add vDSO for x86-64 with gettimeofday/clock_gettime/getcpu")
Reported-by: Dmitry Golovin <dima@golovin.in>
Reported-by: Bill Wendling <morbo@google.com>
Suggested-by: Dmitry Golovin <dima@golovin.in>
Suggested-by: Rui Ueyama <ruiu@google.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Fangrui Song <maskray@google.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20181206191231.192355-1-ndesaulniers@google.com
Link: https://bugs.llvm.org/show_bug.cgi?id=38774
Link: https://github.com/ClangBuiltLinux/linux/issues/31
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 379d98ddf41344273d9718556f761420f4dc80b3 upstream.
The vdso{32,64}.so can fail to link with CC=clang when clang tries to find
a suitable GCC toolchain to link these libraries with.
/usr/bin/ld: arch/x86/entry/vdso/vclock_gettime.o:
access beyond end of merged section (782)
This happens because the host environment leaked into the cross compiler
environment due to the way clang searches for suitable GCC toolchains.
Clang is a retargetable compiler, and each invocation of it must provide
--target=<something> --gcc-toolchain=<something> to allow it to find the
correct binutils for cross compilation. These flags had been added to
KBUILD_CFLAGS, but the vdso code uses CC and not KBUILD_CFLAGS (for various
reasons) which breaks clang's ability to find the correct linker when cross
compiling.
Most of the time this goes unnoticed because the host linker is new enough
to work anyway, or is incompatible and skipped, but this cannot be reliably
assumed.
This change alters the vdso makefile to just use LD directly, which
bypasses clang and thus the searching problem. The makefile will just use
${CROSS_COMPILE}ld instead, which is always what we want. This matches the
method used to link vmlinux.
This drops references to DISABLE_LTO; this option doesn't seem to be set
anywhere, and not knowing what its possible values are, it's not clear how
to convert it from CC to LD flag.
Signed-off-by: Alistair Strachan <astrachan@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: kernel-team@android.com
Cc: joel@joelfernandes.org
Cc: Andi Kleen <andi.kleen@intel.com>
Link: https://lkml.kernel.org/r/20180803173931.117515-1-astrachan@google.com
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 927185c124d62a9a4d35878d7f6d432a166b74e3 upstream.
The kernel uses the OUTPUT_FORMAT linker script command in it's linker
scripts. Most of the time, the -m option is passed to the linker with
correct architecture, but sometimes (at least for x86_64) the -m option
contradicts the OUTPUT_FORMAT directive.
Specifically, arch/x86/boot and arch/x86/realmode/rm produce i386 object
files, but are linked with the -m elf_x86_64 linker flag when building
for x86_64.
The GNU linker manpage doesn't explicitly state any tie-breakers between
-m and OUTPUT_FORMAT. But with BFD and Gold linkers, OUTPUT_FORMAT
overrides the emulation value specified with the -m option.
LLVM lld has a different behavior, however. When supplied with
contradicting -m and OUTPUT_FORMAT values it fails with the following
error message:
ld.lld: error: arch/x86/realmode/rm/header.o is incompatible with elf_x86_64
Therefore, just add the correct -m after the incorrect one (it overrides
it), so the linker invocation looks like this:
ld -m elf_x86_64 -z max-page-size=0x200000 -m elf_i386 --emit-relocs -T \
realmode.lds header.o trampoline_64.o stack.o reboot.o -o realmode.elf
This is not a functional change for GNU ld, because (although not
explicitly documented) OUTPUT_FORMAT overrides -m EMULATION.
Tested by building x86_64 kernel with GNU gcc/ld toolchain and booting
it in QEMU.
[ bp: massage and clarify text. ]
Suggested-by: Dmitry Golovin <dima@golovin.in>
Signed-off-by: George Rimar <grimar@accesssoftek.com>
Signed-off-by: Tri Vo <trong@android.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Tri Vo <trong@android.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Michael Matz <matz@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: morbo@google.com
Cc: ndesaulniers@google.com
Cc: ruiu@google.com
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190111201012.71210-1-trong@android.com
[nc: Fix conflicts due to lack of commit 58ab5e0c2c40 ("Kbuild: arch:
look for generated headers in obtree") in this tree]
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ad15006cc78459d059af56729c4d9bed7c7fd860 upstream.
This causes an issue when trying to build with `make LD=ld.lld` if
ld.lld and the rest of your cross tools aren't in the same directory
(ex. /usr/local/bin) (as is the case for Android's build system), as the
GCC_TOOLCHAIN_DIR then gets set based on `which $(LD)` which will point
where LLVM tools are, not GCC/binutils tools are located.
Instead, select the GCC_TOOLCHAIN_DIR based on another tool provided by
binutils for which LLVM does not provide a substitute for, such as
elfedit.
Fixes: 785f11aa595b ("kbuild: Add better clang cross build support")
Link: https://github.com/ClangBuiltLinux/linux/issues/341
Suggested-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9f834ec18defc369d73ccf9e87a2790bfa05bf46 upstream.
We used to delay switching to the new credentials until after we had
mapped the executable (and possible elf interpreter). That was kind of
odd to begin with, since the new executable will actually then _run_
with the new creds, but whatever.
The bigger problem was that we also want to make sure that we turn off
prof events and tracing before we start mapping the new executable
state. So while this is a cleanup, it's also a fix for a possible
information leak.
Reported-by: Robert Święcki <robert@swiecki.net>
Tested-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Kees Cook <keescook@chromium.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Federico Manuel Bento <up201407890@fc.up.pt>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c978ae9bde582e82a04c63a4071701691dd8b35c ]
We aren't supposed to force a stop+start between every i2c msg
when performing multi message transfers. This should eg. cause
the DDC segment address to be reset back to 0 between writing
the segment address and reading the actual EDID extension block.
To quote the E-DDC spec:
"... this standard requires that the segment pointer be
reset to 00h when a NO ACK or a STOP condition is received."
Since we're going to touch this might as well consult the
I2C_M_STOP flag to determine whether we want to force the stop
or not.
Cc: Brian Vincent <brainn@gmail.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=108081
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180928180403.22499-1-ville.syrjala@linux.intel.com
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e486df39305864604b7e25f2a95d51039517ac57 ]
The dma_desc->bytes_transferred counter tracks the number of bytes
moved by the DMA channel. This is then used to calculate the information
passed back in the in the tegra_dma_tx_status callback, which is usually
fine.
When the DMA channel is configured as continous, then the bytes_transferred
counter will increase over time and eventually overflow to become negative
so the residue count will become invalid and the ALSA sound-dma code will
report invalid hardware pointer values to the application. This results in
some users becoming confused about the playout position and putting audio
data in the wrong place.
To fix this issue, always ensure the bytes_transferred field is modulo the
size of the request. We only do this for the case of the cyclic transfer
done ISR as anyone attempting to move 2GiB of DMA data in one transfer
is unlikely.
Note, we don't fix the issue that we should /never/ transfer a negative
number of bytes so we could make those fields unsigned.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d071ae09a4a1414c1433d5ae9908959a7325b0ad ]
Accessing per-CPU variables is done by finding the offset of the
variable in the per-CPU block and adding it to the address of the
respective CPU's block.
Section 3.10.8 of ld.bfd's documentation states:
For expressions involving numbers, relative addresses and absolute
addresses, ld follows these rules to evaluate terms:
Other binary operations, that is, between two relative addresses
not in the same section, or between a relative address and an
absolute address, first convert any non-absolute term to an
absolute address before applying the operator."
Note that LLVM's linker does not adhere to the GNU ld's implementation
and as such requires implicitly-absolute terms to be explicitly marked
as absolute in the linker script. If not, it fails currently with:
ld.lld: error: ./arch/x86/kernel/vmlinux.lds:153: at least one side of the expression must be absolute
ld.lld: error: ./arch/x86/kernel/vmlinux.lds:154: at least one side of the expression must be absolute
Makefile:1040: recipe for target 'vmlinux' failed
This is not a functional change for ld.bfd which converts the term to an
absolute symbol anyways as specified above.
Based on a previous submission by Tri Vo <trong@android.com>.
Reported-by: Dmitry Golovin <dima@golovin.in>
Signed-off-by: Rafael Ávila de Espíndola <rafael@espindo.la>
[ Update commit message per Boris' and Michael's suggestions. ]
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
[ Massage commit message more, fix typos. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Dmitry Golovin <dima@golovin.in>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Cao Jin <caoj.fnst@cn.fujitsu.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tri Vo <trong@android.com>
Cc: dima@golovin.in
Cc: morbo@google.com
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20181219190145.252035-1-ndesaulniers@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f01a7beb6791f1c419424c1a6958b7d0a289c974 ]
The act8600_sudcdc_voltage_ranges setting does not match the datasheet.
The problems in below entry:
REGULATOR_LINEAR_RANGE(19000000, 191, 255, 400000),
1. The off-by-one min_sel causes wrong volatage calculation.
The min_sel should be 192.
2. According to the datasheet[1] Table 7. (on page 43):
The selector 248 (0b11111000) ~ 255 (0b11111111) are 41.400V.
Also fix off-by-one for ACT8600_SUDCDC_VOLTAGE_NUM.
[1] https://active-semi.com/wp-content/uploads/ACT8600_Datasheet.pdf
Fixes: df3a950e4e ("regulator: act8865: Add act8600 support")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49710c32cd9d6626a77c9f5f978a5f58cb536b35 ]
Previously when doing format enumeration, it was returning all
formats supported by driver, even if they're not supported by hw.
Add missing check for fmt_ver_flag, so it'll be fixed and only those
supported by hw will be returned. Similar thing is already done
in s5p_jpeg_find_format.
It was found by using v4l2-compliance tool and checking result
of VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS test
and using v4l2-ctl to get list of all supported formats.
Tested on s5pv210-galaxys (Samsung i9000 phone).
Fixes: bb677f3ac4 ("[media] Exynos4 JPEG codec v4l2 driver")
Signed-off-by: Pawe? Chmiel <pawel.mikolaj.chmiel@gmail.com>
Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
[hverkuil-cisco@xs4all.nl: fix a few alignment issues]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e2f311a68494a6677c1724bdcb10bada21af37c ]
Following command:
iptables -D FORWARD -m physdev ...
causes connectivity loss in some setups.
Reason is that iptables userspace will probe kernel for the module revision
of the physdev patch, and physdev has an artificial dependency on
br_netfilter (xt_physdev use makes no sense unless a br_netfilter module
is loaded).
This causes the "phydev" module to be loaded, which in turn enables the
"call-iptables" infrastructure.
bridged packets might then get dropped by the iptables ruleset.
The better fix would be to change the "call-iptables" defaults to 0 and
enforce explicit setting to 1, but that breaks backwards compatibility.
This does the next best thing: add a request_module call to checkentry.
This was a stray '-D ... -m physdev' won't activate br_netfilter
anymore.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9227ab5643cb8350449502dd9e3168a873ab0e3b ]
The warning got introduced by commit 930507c18304 ("arm64: add basic
Kconfig symbols for i.MX8"). Since it got enabled for arm64. The warning
haven't been seen before since size_t was 'unsigned int' when built on
arm32.
../drivers/dma/imx-dma.c: In function ‘imxdma_sg_next’:
../include/linux/kernel.h:846:29: warning: comparison of distinct pointer types lacks a cast
(!!(sizeof((typeof(x) *)1 == (typeof(y) *)1)))
^~
../include/linux/kernel.h:860:4: note: in expansion of macro ‘__typecheck’
(__typecheck(x, y) && __no_side_effects(x, y))
^~~~~~~~~~~
../include/linux/kernel.h:870:24: note: in expansion of macro ‘__safe_cmp’
__builtin_choose_expr(__safe_cmp(x, y), \
^~~~~~~~~~
../include/linux/kernel.h:879:19: note: in expansion of macro ‘__careful_cmp’
#define min(x, y) __careful_cmp(x, y, <)
^~~~~~~~~~~~~
../drivers/dma/imx-dma.c:288:8: note: in expansion of macro ‘min’
now = min(d->len, sg_dma_len(sg));
^~~
Rework so that we use min_t and pass in the size_t that returns the
minimum of two values, using the specified type.
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24d48a61f2666630da130cc2ec2e526eacf229e3 ]
Commit '3d035f580699 ("drivers/char/hpet.c: allow user controlled mmap for
user processes")' introduced a new kernel command line parameter hpet_mmap,
that is required to expose the memory map of the HPET registers to
user-space. Unfortunately the kernel command line parameter 'hpet_mmap' is
broken and never takes effect due to missing '=' character in the __setup()
code of hpet_mmap_enable.
Before this patch:
dmesg output with the kernel command line parameter hpet_mmap=1
[ 0.204152] HPET mmap disabled
dmesg output with the kernel command line parameter hpet_mmap=0
[ 0.204192] HPET mmap disabled
After this patch:
dmesg output with the kernel command line parameter hpet_mmap=1
[ 0.203945] HPET mmap enabled
dmesg output with the kernel command line parameter hpet_mmap=0
[ 0.204652] HPET mmap disabled
Fixes: 3d035f5806 ("drivers/char/hpet.c: allow user controlled mmap for user processes")
Signed-off-by: Buland Singh <bsingh@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aef027db48da56b6f25d0e54c07c8401ada6ce21 ]
The virtio-rng driver uses a completion called have_data to wait for a
virtio read to be fulfilled by the hypervisor. The completion is reset
before placing a buffer on the virtio queue and completed by the virtio
callback once data has been written into the buffer.
Prior to this commit, the driver called init_completion on this
completion both during probe as well as when registering virtio buffers
as part of a hwrng read operation. The second of these init_completion
calls should instead be reinit_completion because the have_data
completion has already been inited by probe. As described in
Documentation/scheduler/completion.txt, "Calling init_completion() twice
on the same completion object is most likely a bug".
This bug was present in the initial implementation of virtio-rng in
f7f510ec19 ("virtio: An entropy device, as suggested by hpa"). Back
then the have_data completion was a single static completion rather than
a member of one of potentially multiple virtrng_info structs as
implemented later by 08e53fbdb8 ("virtio-rng: support multiple
virtio-rng devices"). The original driver incorrectly used
init_completion rather than INIT_COMPLETION to reset have_data during
read.
Tested by running `head -c48 /dev/random | hexdump` within crosvm, the
Chrome OS virtual machine monitor, and confirming that the virtio-rng
driver successfully produces random bytes from the host.
Signed-off-by: David Tolnay <dtolnay@gmail.com>
Tested-by: David Tolnay <dtolnay@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 29856308137de1c21eda89411695f4fc6e9780ff ]
This driver sets initial frame width and height to 0x0, which is invalid.
So set it to selection rectangle bounds instead.
This is detected by v4l2-compliance detected.
Cc: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Cc: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ab57b76ebf632bf2231ccabe26bea33868118c6 ]
We increase the default limit for buffer memory allocation by a factor of
10 to 640K to prevent data loss when using fast serial interfaces.
For example when using RS485 without flow-control at speeds of 1Mbit/s
an upwards we've run into problems such as applications being too slow
to read out this buffer (on embedded devices based on imx53 or imx6).
If you want to write transmitted data to a slow SD card and thus have
realtime requirements, this limit can become a problem.
That shouldn't be the case and 640K buffers fix such problems for us.
This value is a maximum limit for allocation only. It has no effect
on systems that currently run fine. When transmission is slow enough
applications and hardware can keep up and increasing this limit
doesn't change anything.
It only _allows_ to allocate more than 2*64K in cases we currently fail to
allocate memory despite having some.
Signed-off-by: Manfred Schlaegl <manfred.schlaegl@ginzinger.com>
Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5388a5b82199facacd3d7ac0d05aca6e8f902fed ]
machine_crash_nonpanic_core() does this:
while (1)
cpu_relax();
because the kernel has crashed, and we have no known safe way to deal
with the CPU. So, we place the CPU into an infinite loop which we
expect it to never exit - at least not until the system as a whole is
reset by some method.
In the absence of erratum 754327, this code assembles to:
b .
In other words, an infinite loop. When erratum 754327 is enabled,
this becomes:
1: dmb
b 1b
It has been observed that on some systems (eg, OMAP4) where, if a
crash is triggered, the system tries to kexec into the panic kernel,
but fails after taking the secondary CPU down - placing it into one
of these loops. This causes the system to livelock, and the most
noticable effect is the system stops after issuing:
Loading crashdump kernel...
to the system console.
The tested as working solution I came up with was to add wfe() to
these infinite loops thusly:
while (1) {
cpu_relax();
wfe();
}
which, without 754327 builds to:
1: wfe
b 1b
or with 754327 is enabled:
1: dmb
wfe
b 1b
Adding "wfe" does two things depending on the environment we're running
under:
- where we're running on bare metal, and the processor implements
"wfe", it stops us spinning endlessly in a loop where we're never
going to do any useful work.
- if we're running in a VM, it allows the CPU to be given back to the
hypervisor and rescheduled for other purposes (maybe a different VM)
rather than wasting CPU cycles inside a crashed VM.
However, in light of erratum 794072, Will Deacon wanted to see 10 nops
as well - which is reasonable to cover the case where we have erratum
754327 enabled _and_ we have a processor that doesn't implement the
wfe hint.
So, we now end up with:
1: wfe
b 1b
when erratum 754327 is disabled, or:
1: dmb
nop
nop
nop
nop
nop
nop
nop
nop
nop
nop
wfe
b 1b
when erratum 754327 is enabled. We also get the dmb + 10 nop
sequence elsewhere in the kernel, in terminating loops.
This is reasonable - it means we get the workaround for erratum
794072 when erratum 754327 is enabled, but still relinquish the dead
processor - either by placing it in a lower power mode when wfe is
implemented as such or by returning it to the hypervisior, or in the
case where wfe is a no-op, we use the workaround specified in erratum
794072 to avoid the problem.
These as two entirely orthogonal problems - the 10 nops addresses
erratum 794072, and the wfe is an optimisation that makes the system
more efficient when crashed either in terms of power consumption or
by allowing the host/other VMs to make use of the CPU.
I don't see any reason not to use kexec() inside a VM - it has the
potential to provide automated recovery from a failure of the VMs
kernel with the opportunity for saving a crashdump of the failure.
A panic() with a reboot timeout won't do that, and reading the
libvirt documentation, setting on_reboot to "preserve" won't either
(the documentation states "The preserve action for an on_reboot event
is treated as a destroy".) Surely it has to be a good thing to
avoiding having CPUs spinning inside a VM that is doing no useful
work.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8cd09a3dd3e176c62da67efcd477a44a8d87185e ]
If of_platform_populate() fails in gsbi_probe(),
gsbi->hclk is left undisabled.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11907e9d3533648615db08140e3045b829d2c141 ]
The of_find_device_by_node() takes a reference to the underlying device
structure, we should release that reference.
Signed-off-by: Wen Yang <yellowriver2010@hotmil.com>
Cc: Timur Tabi <timur@kernel.org>
Cc: Nicolin Chen <nicoleotsuka@gmail.com>
Cc: Xiubo Li <Xiubo.Lee@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: alsa-devel@alsa-project.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 596b5a5dd1bc2fa019fdaaae522ef331deef927f ]
Currently sysfs_strtoul_clamp() is defined as,
82 #define sysfs_strtoul_clamp(file, var, min, max) \
83 do { \
84 if (attr == &sysfs_ ## file) \
85 return strtoul_safe_clamp(buf, var, min, max) \
86 ?: (ssize_t) size; \
87 } while (0)
The problem is, if bit width of var is less then unsigned long, min and
max may not protect var from integer overflow, because overflow happens
in strtoul_safe_clamp() before checking min and max.
To fix such overflow in sysfs_strtoul_clamp(), to make min and max take
effect, this patch adds an unsigned long variable, and uses it to macro
strtoul_safe_clamp() to convert an unsigned long value in range defined
by [min, max]. Then assign this value to var. By this method, if bit
width of var is less than unsigned long, integer overflow won't happen
before min and max are checking.
Now sysfs_strtoul_clamp() can properly handle smaller data type like
unsigned int, of cause min and max should be defined in range of
unsigned int too.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c27a3953e92eb0b22dbb03d599f543a05f9574e ]
People may set sequential_cutoff of a cached device via sysfs file,
but current code does not check input value overflow. E.g. if value
4294967295 (UINT_MAX) is written to file sequential_cutoff, its value
is 4GB, but if 4294967296 (UINT_MAX + 1) is written into, its value
will be 0. This is an unexpected behavior.
This patch replaces d_strtoi_h() by sysfs_strtoul_clamp() to convert
input string to unsigned integer value, and limit its range in
[0, UINT_MAX]. Then the input overflow can be fixed.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a91fbda49f746119828f7e8ad0f0aa2ab0578f65 ]
Cache set sysfs entry io_error_halflife is used to set c->error_decay.
c->error_decay is in type unsigned int, and it is converted by
strtoul_or_return(), therefore overflow to c->error_decay is possible
for a large input value.
This patch fixes the overflow by using strtoul_safe_clamp() to convert
input string to an unsigned long value in range [0, UINT_MAX], then
divides by 88 and set it to c->error_decay.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9c0b2afe820fa3b3f8258a659daee2cc71ca3ef ]
BE dai links only have internal PCM's and their substream ops may
not be set. Suspending these PCM's will result in their
ops->trigger() being invoked and cause a kernel oops.
So skip suspending PCM's if their ops are NULL.
[ NOTE: this change is required now for following the recent PCM core
change to get rid of snd_pcm_suspend() call. Since DPCM BE takes
the runtime carried from FE while keeping NULL ops, it can hit this
bug. See details at:
https://github.com/thesofproject/linux/pull/582
-- tiwai ]
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de9c0d49d85dc563549972edc5589d195cd5e859 ]
While building arm32 allyesconfig, I ran into the following errors:
arch/arm/lib/xor-neon.c:17:2: error: You should compile this file with
'-mfloat-abi=softfp -mfpu=neon'
In file included from lib/raid6/neon1.c:27:
/home/nathan/cbl/prebuilt/lib/clang/8.0.0/include/arm_neon.h:28:2:
error: "NEON support not enabled"
Building V=1 showed NEON_FLAGS getting passed along to Clang but
__ARM_NEON__ was not getting defined. Ultimately, it boils down to Clang
only defining __ARM_NEON__ when targeting armv7, rather than armv6k,
which is the '-march' value for allyesconfig.
>From lib/Basic/Targets/ARM.cpp in the Clang source:
// This only gets set when Neon instructions are actually available, unlike
// the VFP define, hence the soft float and arch check. This is subtly
// different from gcc, we follow the intent which was that it should be set
// when Neon instructions are actually available.
if ((FPU & NeonFPU) && !SoftFloat && ArchVersion >= 7) {
Builder.defineMacro("__ARM_NEON", "1");
Builder.defineMacro("__ARM_NEON__");
// current AArch32 NEON implementations do not support double-precision
// floating-point even when it is present in VFP.
Builder.defineMacro("__ARM_NEON_FP",
"0x" + Twine::utohexstr(HW_FP & ~HW_FP_DP));
}
Ard Biesheuvel recommended explicitly adding '-march=armv7-a' at the
beginning of the NEON_FLAGS definitions so that __ARM_NEON__ always gets
definined by Clang. This doesn't functionally change anything because
that code will only run where NEON is supported, which is implicitly
armv7.
Link: https://github.com/ClangBuiltLinux/linux/issues/287
Suggested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ddb0869bfc1bca6cfc592c74c64a026f936638c ]
I've stumbled upon a kernel crash and the logs
pointed me towards the lp5562 driver:
> <4>[306013.841294] lp5562 0-0030: Direct firmware load for lp5562 failed with error -2
> <4>[306013.894990] lp5562 0-0030: Falling back to user helper
> ...
> <3>[306073.924886] lp5562 0-0030: firmware request failed
> <1>[306073.939456] Unable to handle kernel NULL pointer dereference at virtual address 00000000
> <4>[306074.251011] PC is at _raw_spin_lock+0x1c/0x58
> <4>[306074.255539] LR is at release_firmware+0x6c/0x138
> ...
After taking a look I noticed firmware_release()
could be called with either NULL or a dangling
pointer.
Fixes: 10c06d178d ("leds-lp55xx: support firmware interface")
Signed-off-by: Michal Kazior <michal@plume.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d20dcefe471763f23ad538369ec65b51993ffff ]
Fix the assigned type of mem2mem buffer handling API.
Namely, these functions:
v4l2_m2m_next_buf
v4l2_m2m_last_buf
v4l2_m2m_buf_remove
v4l2_m2m_next_src_buf
v4l2_m2m_next_dst_buf
v4l2_m2m_last_src_buf
v4l2_m2m_last_dst_buf
v4l2_m2m_src_buf_remove
v4l2_m2m_dst_buf_remove
return a struct vb2_v4l2_buffer, and not a struct vb2_buffer.
Fixing this is necessary to fix the mem2mem buffer handling API,
changing the return to the correct struct vb2_v4l2_buffer instead
of a void pointer.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30fa627b32230737bc3f678067e2adfecf956987 ]
Fix the assigned type of mem2mem buffer handling API.
Namely, these functions:
v4l2_m2m_next_buf
v4l2_m2m_last_buf
v4l2_m2m_buf_remove
v4l2_m2m_next_src_buf
v4l2_m2m_next_dst_buf
v4l2_m2m_last_src_buf
v4l2_m2m_last_dst_buf
v4l2_m2m_src_buf_remove
v4l2_m2m_dst_buf_remove
return a struct vb2_v4l2_buffer, and not a struct vb2_buffer.
Fixing this is necessary to fix the mem2mem buffer handling API,
changing the return to the correct struct vb2_v4l2_buffer instead
of a void pointer.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a88f89885c7cf65c62793f385261a6e3315178a ]
Fix the assigned type of mem2mem buffer handling API.
Namely, these functions:
v4l2_m2m_next_buf
v4l2_m2m_last_buf
v4l2_m2m_buf_remove
v4l2_m2m_next_src_buf
v4l2_m2m_next_dst_buf
v4l2_m2m_last_src_buf
v4l2_m2m_last_dst_buf
v4l2_m2m_src_buf_remove
v4l2_m2m_dst_buf_remove
return a struct vb2_v4l2_buffer, and not a struct vb2_buffer.
Fixing this is necessary to fix the mem2mem buffer handling API,
changing the return to the correct struct vb2_v4l2_buffer instead
of a void pointer.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43c145195c7fc3025ee7ecfc67112ac1c82af7c2 ]
Fix the assigned type of mem2mem buffer handling API.
Namely, these functions:
v4l2_m2m_next_buf
v4l2_m2m_last_buf
v4l2_m2m_buf_remove
v4l2_m2m_next_src_buf
v4l2_m2m_next_dst_buf
v4l2_m2m_last_src_buf
v4l2_m2m_last_dst_buf
v4l2_m2m_src_buf_remove
v4l2_m2m_dst_buf_remove
return a struct vb2_v4l2_buffer, and not a struct vb2_buffer.
Fixing this is necessary to fix the mem2mem buffer handling API,
changing the return to the correct struct vb2_v4l2_buffer instead
of a void pointer.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8fa857da9744f513036df1c43ab57f338941ae7d ]
The of_find_device_by_node() takes a reference to the underlying device
structure, we should release that reference.
Detected by coccinelle with the following warnings:
./sound/soc/fsl/imx-sgtl5000.c:169:1-7: ERROR: missing put_device;
call of_find_device_by_node on line 105, but without a corresponding
object release within this function.
./sound/soc/fsl/imx-sgtl5000.c:177:1-7: ERROR: missing put_device;
call of_find_device_by_node on line 105, but without a corresponding
object release within this function.
Signed-off-by: Wen Yang <yellowriver2010@hotmail.com>
Cc: Timur Tabi <timur@kernel.org>
Cc: Nicolin Chen <nicoleotsuka@gmail.com>
Cc: Xiubo Li <Xiubo.Lee@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: alsa-devel@alsa-project.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03d309711d687460d1345de8a0363f45b1c8cd11 ]
Commit 489338a717a0 ("perf tests evsel-tp-sched: Fix bitwise operator")
causes test case 14 "Parse sched tracepoints fields" to fail on s390.
This test succeeds on x86.
In fact this test now fails on all architectures with type char treated
as type unsigned char.
The root cause is the signed-ness of character arrays in the tracepoints
sched_switch for structure members prev_comm and next_comm.
On s390 the output of:
[root@m35lp76 perf]# cat /sys/kernel/debug/tracing/events/sched/sched_switch/format
name: sched_switch
ID: 287
format:
field:unsigned short common_type; offset:0; size:2; signed:0;
...
field:char prev_comm[16]; offset:8; size:16; signed:0;
...
field:char next_comm[16]; offset:40; size:16; signed:0;
reveals the character arrays prev_comm and next_comm are per
default unsigned char and have values in the range of 0..255.
On x86 both fields are signed as this output shows:
[root@f29]# cat /sys/kernel/debug/tracing/events/sched/sched_switch/format
name: sched_switch
ID: 287
format:
field:unsigned short common_type; offset:0; size:2; signed:0;
...
field:char prev_comm[16]; offset:8; size:16; signed:1;
...
field:char next_comm[16]; offset:40; size:16; signed:1;
and the character arrays prev_comm and next_comm are per default signed
char and have values in the range of -1..127. The implementation of
type char is architecture specific.
Since the character arrays in both tracepoints sched_switch and
sched_wakeup should contain ascii characters, simply omit the check for
signedness in the test case.
Output before:
[root@m35lp76 perf]# ./perf test -F 14
14: Parse sched tracepoints fields :
--- start ---
sched:sched_switch: "prev_comm" signedness(0) is wrong, should be 1
sched:sched_switch: "next_comm" signedness(0) is wrong, should be 1
sched:sched_wakeup: "comm" signedness(0) is wrong, should be 1
---- end ----
14: Parse sched tracepoints fields : FAILED!
[root@m35lp76 perf]#
Output after:
[root@m35lp76 perf]# ./perf test -Fv 14
14: Parse sched tracepoints fields :
--- start ---
---- end ----
Parse sched tracepoints fields: Ok
[root@m35lp76 perf]#
Fixes: 489338a717a0 ("perf tests evsel-tp-sched: Fix bitwise operator")
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Link: http://lkml.kernel.org/r/20190219153639.31267-1-tmricht@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2612d723aadcf8281f9bf8305657129bd9f3cd57 ]
Using CX-3 virtual functions, either from a bare-metal machine or
pass-through from a VM, MAD packets are proxied through the PF driver.
Since the VF drivers have separate name spaces for MAD Transaction Ids
(TIDs), the PF driver has to re-map the TIDs and keep the book keeping
in a cache.
Following the RDMA Connection Manager (CM) protocol, it is clear when
an entry has to evicted form the cache. But life is not perfect,
remote peers may die or be rebooted. Hence, it's a timeout to wipe out
a cache entry, when the PF driver assumes the remote peer has gone.
During workloads where a high number of QPs are destroyed concurrently,
excessive amount of CM DREQ retries has been observed
The problem can be demonstrated in a bare-metal environment, where two
nodes have instantiated 8 VFs each. This using dual ported HCAs, so we
have 16 vPorts per physical server.
64 processes are associated with each vPort and creates and destroys
one QP for each of the remote 64 processes. That is, 1024 QPs per
vPort, all in all 16K QPs. The QPs are created/destroyed using the
CM.
When tearing down these 16K QPs, excessive CM DREQ retries (and
duplicates) are observed. With some cat/paste/awk wizardry on the
infiniband_cm sysfs, we observe as sum of the 16 vPorts on one of the
nodes:
cm_rx_duplicates:
dreq 2102
cm_rx_msgs:
drep 1989
dreq 6195
rep 3968
req 4224
rtu 4224
cm_tx_msgs:
drep 4093
dreq 27568
rep 4224
req 3968
rtu 3968
cm_tx_retries:
dreq 23469
Note that the active/passive side is equally distributed between the
two nodes.
Enabling pr_debug in cm.c gives tons of:
[171778.814239] <mlx4_ib> mlx4_ib_multiplex_cm_handler: id{slave:
1,sl_cm_id: 0xd393089f} is NULL!
By increasing the CM_CLEANUP_CACHE_TIMEOUT from 5 to 30 seconds, the
tear-down phase of the application is reduced from approximately 90 to
50 seconds. Retries/duplicates are also significantly reduced:
cm_rx_duplicates:
dreq 2460
[]
cm_tx_retries:
dreq 3010
req 47
Increasing the timeout further didn't help, as these duplicates and
retries stems from a too short CMA timeout, which was 20 (~4 seconds)
on the systems. By increasing the CMA timeout to 22 (~17 seconds), the
numbers fell down to about 10 for both of them.
Adjustment of the CMA timeout is not part of this commit.
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Acked-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
