Due to an existing HW workaround, the UFP_EN_CMD bit may end up
getting cleared even after having been set. The result of this
is the Type-C state machine returns to DRP behavior despite SW
intention to force sink mode, such as PR Swap or Try.SNK.
Temporarily disable this particular HW trigger whenever the
typec_power_role property is getting set to sink-only mode, and
restore it when leaving sink mode.
Change-Id: I21e840bfeee3ad88b0562645378b1fea200e3803
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
pimem bus master is starving for data from ddr and time out is
observed with QoS priority set to 0, so increase the QoS priority
for pimem bus master to 1.
Change-Id: Ie90d0a41953e03d8cba9843fd8fb4f7dc511a62d
Signed-off-by: Odelu Kukatla <okukatla@codeaurora.org>
In runtime resume scenarios we first enable the HW resources, clocks and
then set the gpio to UART functionalities. When GPIOS are changing the
state RX line samples as zero resulting in RX Break detection. This stops
data coming from BT SOC sending to the BT host causing failures.
Modify the GPIO config sequence such that GPIO functionalities changed
only when resources like Clocks are OFF.
Change-Id: Iaf3b7c7a66dd83fc631e4a779a804ef98836e00b
Signed-off-by: Mukesh Kumar Savaliya <msavaliy@codeaurora.org>
This is the reference driver source code for ST
Touchscreen of version 4.1.0. It is used for QVR8998
touchscreen.
(cherry picked from commit 2cd09314337d614e69d0ebd99afb71d99d31b69a)
Signed-off-by: chenx <chenxiang0527@thundersoft.com>
Git-commit: 2cd09314337d614e69d0ebd99afb71d99d31b69a
Git-repo: https://source.codeaurora.org/quic/la/kernel/msm-3.10
CRs-Fixed: 1106217
Change-Id: I5c26deaa3943ff300ce9835678bb4a550e40f096
Signed-off-by: Jin Fu <jinf@codeaurora.org>
When hotspot tethering is toggled quickly
WLAN_AP_CONNECT is received even before all
the filter rules are cleaned up for the previous
DISCONNECT. As the sticky_rear is set, default
rule is not added at the end. Make a change to
reset sticky_rear when default rules are deleted.
Change-Id: I8b63fec360e91ddd5f5267fe74c769547bb5bbfe
Acked-by: Chaitanya Pratapa <cpratapa@qti.qualcomm.com>
Signed-off-by: Utkarsh Saxena <usaxena@codeaurora.org>
In case count is not multiple of 4, there is a read access in
wil_memcpy_toio_32() from outside src buffer boundary.
In wil_memcpy_fromio_32(), in case count is not multiple of 4, there
is a write access to outside dst io memory boundary.
Fix these issues with proper handling of the last 1 to 4 copied bytes.
Change-Id: Iff7853bc4803a01449ddcee996a54a0dccc1db1a
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Skip checking the SWITCHABLE_SIGNALING_VOLTAGE bit of MCI_GENERICS
register while checking power status on SDHC v5.0 onwards.
This bit shows whether controller supports switching of IO signaling
voltage or not. On SDHC v5.0, switchable signaling voltage support
is present by default and this bit was removed. So we can skip checking
this bit in case of v5.0 controller.
Without this patch, driver tries to read a non-existing bit field which is
causing driver to proceed without waiting for pwr-irq. In some case its
turning off the clock even before pwr irq finishes thus resulting in
un-clocked access errors.
Change-Id: I5beaf5bf043999522e3f2ec537568524c5aec4bf
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
In case the application is still issuing the requests after
the low-level driver is shutdown, IO errors are expected.
Ratelimit those errors with the default ratelimit to avoid
watchdog bark issue in some cases.
Change-Id: Ida436cbf1be9556f456652e72bc1dac508abd047
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
While checking the profile integrity word to determine whether a
profile load is required or not, whitelist the values so that
profile loading cannot be skipped because of a garbage value
present.
Change-Id: Iff1d116541d07dbb39de966d98fa69b76aeab93d
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
Instead of using a flag to retain the interrupt enabled status
of delta_bsoc interrupt, switch it to use a votable instead. This
improves the readability of code by not worrying about the flag.
While at it, fix cleaning up the resources in some error paths
during driver probe.
Change-Id: I2c17a9d90c7b549435caa75da81f4c4779ea3344
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
Create a sysfs entry for each RC (root complex) so
that clients can manually trigger enumeration from
userspace.
Change-Id: I88b1276d95a2a894759a2f122621e10e171d6528
Signed-off-by: Tony Truong <truong@codeaurora.org>
ESOC IOCTL was designed to transfer data of type unsigned int, but
was pushing data of unsigned long type. Hence causing data corruption
in user space. Fix this by changing put user to use unsigned int.
Change-Id: Ia233eedd76f1ca1ec3036889d6764e568ee975dd
Signed-off-by: Arun KS <arunks@codeaurora.org>
When USB host is re-enumerating USB MTP device multiple time, it
has been observed that USB MTP enumeration fails. USB MTP host
side environment (i.e. libmtp) is looking for USB MTP device to
pass string descriptor as "MTP" for successful enumeration. Due
to iInterface ID conflict, USB device is passing next interface
related string descriptor instead of USB MTP interface related
string descriptor. This results into no enumeration with USB MTP
configuration. Fix this issue by resetting mtp_string_defs string
descriptor id to zero, so next mtp_function_bind() call re-allocates
string ID.
CRs-Fixed: 2024744
Change-Id: Iad290ad480ccf23bd514a67128541d7ff67de1a5
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
While running a single stream UDPv6 test, we observed that amount
of CPU spent in NET_RX softirq was much greater than UDPv4 for an
equivalent receive rate. The test here was run on an ARM64 based
Android system. On further analysis with perf, we found that UDPv6
was spending significant time in the statistics netfilter targets
which did socket lookup per packet. These statistics rules perform
a lookup when there is no socket associated with the skb. Since
there are multiple instances of these rules based on UID, there
will be equal number of lookups per skb.
By introducing early demux for UDPv6, we avoid the redundant lookups.
This also helped to improve the performance (800Mbps -> 870Mbps) on a
CPU limited system in a single stream UDPv6 receive test with 1450
byte sized datagrams using iperf.
v1->v2: Use IPv6 cookie to validate dst instead of 0 as suggested
by Eric
CRs-Fixed: 1114946
Change-Id: I2a59058656863c2e20629fe30fbbe3847319f439
Git-commit: 5425077d73e0c8e7e9267ca8397cc0e2293c1fb9
Git-repo: https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable ok_to_qnovo immediately after charging is disabled while pulse
train is in progress. The flag property ok_to_qnovo indicates qnovno
charging readiness, A delay in doing so could make a normal charging
stop mistakenly treated as an error.
Change-Id: If0c43a4e05b2e0f8cc0ce9a9edca15f466c7fbff
Signed-off-by: Harry Yang <harryy@codeaurora.org>
POWER_SUPPLY_PROP_INPUT_CURRENT_LIMITED - indicate if the switcher
is acting in input limited state.
POWER_SUPPLY_PROP_CURRENT_MAX - set/get usb input current limit in
parallel charger.
Change-Id: I3827735a3900680e3e79104e388c2712f12cbbfb
Signed-off-by: Harry Yang <harryy@codeaurora.org>
In parallel configuration, suspend one charger usb input before the
other enters boost mode. Even more so in USBIN-USBIN mode.
Change-Id: I63728421b7697e70bbd83c4c82203b7ebafdaa9f
Signed-off-by: Harry Yang <harryy@codeaurora.org>
Expose vbus regulator from smb138x in USBIN-USBIN parallel mode.
Change-Id: I3581cbc7ffade0d25363038c25e40e35bd4fce28
Signed-off-by: Harry Yang <harryy@codeaurora.org>
The current code only supports 8 clients max. There are
situations where we will need more than that.
Bump it up to 16.
Change-Id: I7a32f67b3a4579ec79eb4f0e2a971a1a3a29a7c1
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
For DPCD read failures, set link parameters corresponding to
the fail safe link resolution to conform to the display port
specification.
CRs-Fixed: 2010344
Change-Id: I06f56f508fe7adcb9e76f1a8597fc59cdadd741b
Signed-off-by: Aravind Venkateswaran <aravindh@codeaurora.org>
Detailed Timing Descriptors (DTDs) listed in the EDID data contain
the information about the horizontal addressable video pixels for
each resolution. The maximum value that can be specified for this
field is 4095. In certain instances, a sink may list a resolution
with 4096 horizontal addressable video pixels in the DTD by listing
a value of 4095. If this value is parsed as is, it can lead to
incorrect behavior. Fix this by explicitly updating the value to
4096.
CRs-Fixed: 2020154
Change-Id: I035bbef7d245c7cdd75a5bba8719fcca4592d8b7
Signed-off-by: Aravind Venkateswaran <aravindh@codeaurora.org>
In macro QSEECOM_ALIGN, change (x + QSEECOM_ALIGN_SIZE) to
(x + QSEECOM_ALIGN_MASK); otherwise, when x is already aligned,
QSEECOM_ALIGN(x) will get (x + QSEECOM_ALIGN_SIZE), but it should
be x. Also, remove the dulplicate QSEECOM_ALIGN definition
in hdcp.c and mpq_sdmx.c, since they already include
"qseecom_kernel.h"
Change-Id: I9dbcadb618372fce71c2ff7ab62ca691afe7c7fa
Signed-off-by: Zhen Kong <zkong@codeaurora.org>
During link training, capture RC LTSSM state every 5ms
until link comes up or fails. Output will be stored
in PCIe IPC logs.
Change-Id: I41a0bbc75144ea77dfa61374dbcc5591ca63b28f
Signed-off-by: Tony Truong <truong@codeaurora.org>
Adreno GPUs have a certain number of fixed performance counters
most of which can be programmed to a large number of different
items (countables). A centralized database in the kernel is
needed to make the most efficient use of counters across processes.
Add performance counter tracking and APIs to allow applications to
reserve performance counters by requesting a group ID and a countable
(countables differ from block to block). The kernel will check to
see if an active counter is already selected for that countable or
if a new one should be assigned. Different processes can share the
same counter if they both need the same countable.
Counters are reserved with DRM_IOCTL_MSM_COUNTER_GET which returns
a counter ID for the reserved counter and the hi/lo offset of
the counter register. The reserving application can either read the
counter from within a PM4 stream or it can use the group ID and
counter ID and read the value of the counter with
DRM_MSM_COUNTER_READ. After the counter is no longer needed
DRM_IOCTL_MSM_COUNTER_PUT returns it and it can be released for
other countables if no other processes are sharing it.
Reservations are tracked for each process and cleaned up if the
process dies without putting back the counters.
Change-Id: Ic0dedbadc45e85ab0063331b39ca6f3289523038
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Remove the check in a5xx_idle() to see if idle is being called
on the current ring. a5xx_idle() is to used make sure the
commands in the specified ring have completed and it is entirely
reasonably to expect that a ring switch might need to be
executed first.
Change-Id: Ic0dedbadf45c7f624093efae72f3a9d75dc6857d
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Update a5xx rnddb database to add some VBIF registers for clearing
and enabling performance counters.
Change-Id: Ic0dedbada994e916527e8c44e2cf0a20115985a9
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
