commit 3a5e969bb2f6692a256352649355d56d018d6b88 upstream.
The code currently relies on refcounting to disable IRQs from within the
IRQ handler and re-enabling them again after the tasklet has run.
However, due to race conditions sometimes the IRQ handler might be
called twice, or the tasklet may not run at all (if interrupted in the
middle of a reset).
This can cause nasty imbalances in the irq-disable refcount which will
get the driver permanently stuck until the entire radio has been stopped
and started again (ath_reset will not recover from this).
Instead of using this fragile logic, change the code to ensure that
running the irq handler during tasklet processing is safe, and leave the
refcount untouched.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01d4d673558985d9a118e1e05026633c3e2ade9b upstream.
This patch addresses a long-standing bug with multi-session
(eg: iscsi-target + iser-target) se_node_acl dynamic free
withini transport_deregister_session().
This bug is caused when a storage endpoint is configured with
demo-mode (generate_node_acls = 1 + cache_dynamic_acls = 1)
initiators, and initiator login creates a new dynamic node acl
and attaches two sessions to it.
After that, demo-mode for the storage instance is disabled via
configfs (generate_node_acls = 0 + cache_dynamic_acls = 0) and
the existing dynamic acl is never converted to an explicit ACL.
The end result is dynamic acl resources are released twice when
the sessions are shutdown in transport_deregister_session().
If the storage instance is not changed to disable demo-mode,
or the dynamic acl is converted to an explict ACL, or there
is only a single session associated with the dynamic ACL,
the bug is not triggered.
To address this big, move the release of dynamic se_node_acl
memory into target_complete_nacl() so it's only freed once
when se_node_acl->acl_kref reaches zero.
(Drop unnecessary list_del_init usage - HCH)
Reported-by: Rob Millner <rlm@daterainc.com>
Tested-by: Rob Millner <rlm@daterainc.com>
Cc: Rob Millner <rlm@daterainc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21aaa23b0ebbd19334fa461370c03cbb076b3295 upstream.
This patch addresses a long standing race where obtaining
se_node_acl->acl_kref in __transport_register_session()
happens a bit too late, and leaves open the potential
for core_tpg_del_initiator_node_acl() to hit a NULL
pointer dereference.
Instead, take ->acl_kref in core_tpg_get_initiator_node_acl()
while se_portal_group->acl_node_mutex is held, and move the
final target_put_nacl() from transport_deregister_session()
into transport_free_session() so that fabric driver login
failure handling using the modern method to still work
as expected.
Also, update core_tpg_get_initiator_node_acl() to take
an extra reference for dynamically generated acls for
demo-mode, before returning to fabric caller. Also
update iscsi-target sendtargets special case handling
to use target_tpg_has_node_acl() when checking if
demo_mode_discovery == true during discovery lookup.
Note the existing wait_for_completion(&acl->acl_free_comp)
in core_tpg_del_initiator_node_acl() does not change.
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 916cafdc95843fb9af5fd5f83ca499d75473d107 upstream.
There were some bugs in the JNE64 and JLT64 comparision macros. This fixes
them, improves comments, and cleans up the file while we are at it.
Reported-by: Stephen Röttger <sroettger@google.com>
Signed-off-by: Mathias Svensson <idolf@google.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4753d8a24d4588657bc0a4cd66d4e282dff15c8c upstream.
If the file system requires journal recovery, and the device is
read-ony, return EROFS to the mount system call. This allows xfstests
generic/050 to pass.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97abd7d4b5d9c48ec15c425485f054e1c15e591b upstream.
If the journal is aborted, the needs_recovery feature flag should not
be removed. Otherwise, it's the journal might not get replayed and
this could lead to more data getting lost.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb5efbcb762aee4b454b04f7115f73ccbcf8f0ef upstream.
The write_end() function must always unlock the page and drop its ref
count, even on an error.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b136499e906460919f0d21a49db1aaccf0ae963 upstream.
ext4_journalled_write_end() did not propely handle all the cases when
generic_perform_write() did not copy all the data into the target page
and could mark buffers with uninitialized contents as uptodate and dirty
leading to possible data corruption (which would be quickly fixed by
generic_perform_write() retrying the write but still). Fix the problem
by carefully handling the case when the page that is written to is not
uptodate.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd648b8a8fd5071d232242d5ee7ee3c0815776af upstream.
If filesystem groups are artifically small (using parameter -g to
mkfs.ext4), ext4_mb_normalize_request() can result in a request that is
larger than a block group. Trim the request size to not confuse
allocation code.
Reported-by: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 03e916fa8b5577d85471452a3d0c5738aa658dae upstream.
Inside ext4_ext_shift_extents() function ext4_find_extent() is called
without EXT4_EX_NOCACHE flag, which should prevent cache population.
This leads to oudated offsets in the extents tree and wrong blocks
afterwards.
Patch fixes the problem providing EXT4_EX_NOCACHE flag for each
ext4_find_extents() call inside ext4_ext_shift_extents function.
Fixes: 331573febb
Signed-off-by: Roman Pen <roman.penyaev@profitbricks.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: Namjae Jeon <namjae.jeon@samsung.com>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a9b8cba62c0741109c33a2be700ff3d7703a7c2 upstream.
While doing 'insert range' start block should be also shifted right.
The bug can be easily reproduced by the following test:
ptr = malloc(4096);
assert(ptr);
fd = open("./ext4.file", O_CREAT | O_TRUNC | O_RDWR, 0600);
assert(fd >= 0);
rc = fallocate(fd, 0, 0, 8192);
assert(rc == 0);
for (i = 0; i < 2048; i++)
*((unsigned short *)ptr + i) = 0xbeef;
rc = pwrite(fd, ptr, 4096, 0);
assert(rc == 4096);
rc = pwrite(fd, ptr, 4096, 4096);
assert(rc == 4096);
for (block = 2; block < 1000; block++) {
rc = fallocate(fd, FALLOC_FL_INSERT_RANGE, 4096, 4096);
assert(rc == 0);
for (i = 0; i < 2048; i++)
*((unsigned short *)ptr + i) = block;
rc = pwrite(fd, ptr, 4096, 4096);
assert(rc == 4096);
}
Because start block is not included in the range the hole appears at
the wrong offset (just after the desired offset) and the following
pwrite() overwrites already existent block, keeping hole untouched.
Simple way to verify wrong behaviour is to check zeroed blocks after
the test:
$ hexdump ./ext4.file | grep '0000 0000'
The root cause of the bug is a wrong range (start, stop], where start
should be inclusive, i.e. [start, stop].
This patch fixes the problem by including start into the range. But
not to break left shift (range collapse) stop points to the beginning
of the a block, not to the end.
The other not obvious change is an iterator check on validness in a
main loop. Because iterator is unsigned the following corner case
should be considered with care: insert a block at 0 offset, when stop
variables overflows and never becomes less than start, which is 0.
To handle this special case iterator is set to NULL to indicate that
end of the loop is reached.
Fixes: 331573febb
Signed-off-by: Roman Pen <roman.penyaev@profitbricks.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: Namjae Jeon <namjae.jeon@samsung.com>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e02898b423802b1f3a3aaa7f16e896da069ba8f7 upstream.
loop_reread_partitions() needs to do I/O, but we just froze the queue,
so we end up waiting forever. This can easily be reproduced with losetup
-P. Fix it by moving the reread to after we unfreeze the queue.
Fixes: ecdd09597a57 ("block/loop: fix race between I/O and set_status")
Reported-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e112666b4959b25a8552d63bc564e1059be703e8 upstream.
If the journal has been aborted, we shouldn't mark the underlying
buffer head as dirty, since that will cause the metadata block to get
modified. And if the journal has been aborted, we shouldn't allow
this since it will almost certainly lead to a corrupted file system.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 907565337ebf998a68cb5c5b2174ce5e5da065eb upstream.
Userspace applications should be allowed to expect the membarrier system
call with MEMBARRIER_CMD_SHARED command to issue memory barriers on
nohz_full CPUs, but synchronize_sched() does not take those into
account.
Given that we do not want unrelated processes to be able to affect
real-time sensitive nohz_full CPUs, simply return ENOSYS when membarrier
is invoked on a kernel with enabled nohz_full CPUs.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
CC: Josh Triplett <josh@joshtriplett.org>
CC: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Rik van Riel <riel@redhat.com>
Acked-by: Lai Jiangshan <jiangshanlai@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb72d0bb84eee5d0dc3044fd17b75e7101dabb57 upstream.
sd_check_events() is called asynchronously, and might race
with device removal. So always take a disk reference when
processing the event to avoid the device being removed while
the event is processed.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Jinpu Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 857de6e00778738dc3d61f75acbac35bdc48e533 upstream.
The device handler needs to check if a given queue belongs to a scsi
device; only then does it make sense to attach a device handler.
[mkp: dropped flags]
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c421530bf848604e97d0785a03b3fe2c62775083 upstream.
The driver currently checks the SELF_TEST_FAILED first and then
KERNEL_PANIC next. Under error conditions(boot code failure) both
SELF_TEST_FAILED and KERNEL_PANIC can be set at the same time.
The driver has the capability to reset the controller on an KERNEL_PANIC,
but not on SELF_TEST_FAILED.
Fixed by first checking KERNEL_PANIC and then the others.
Fixes: e8b12f0fb8 ([SCSI] aacraid: Add new code for PMC-Sierra's SRC base controller family)
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <David.Carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40630f462824ee24bc00d692865c86c3828094e0 upstream.
On I/O errors, the Windows driver doesn't set data_transfer_length
on error conditions other than SRB_STATUS_DATA_OVERRUN.
In these cases we need to set data_transfer_length to 0,
indicating there is no data transferred. On SRB_STATUS_DATA_OVERRUN,
data_transfer_length is set by the Windows driver to the actual data transferred.
Reported-by: Shiva Krishna <Shiva.Krishna@nimblestorage.com>
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bba5dc332ec2d3a685cb4dae668c793f6a3713a3 upstream.
When sense message is present on error, we should pass along to the upper
layer to decide how to deal with the error.
This patch fixes connectivity issues with Fiber Channel devices.
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3cd6d3d9b1abab8dcdf0800224ce26daac24eea2 upstream.
Properly set SRB flags when hosting device supports tagged queuing.
This patch improves the performance on Fiber Channel disks.
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca763d0a53b264a650342cee206512bc92ac7050 upstream.
A rounding bug due to compiler generated temporary being 32bit was found
in remap_to_cache(). A localized cast in remap_to_cache() fixes the
corruption but this preferred fix (changing from uint32_t to sector_t)
eliminates potential for future rounding errors elsewhere.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95e91b831f87ac8e1f8ed50c14d709089b4e01b8 upstream.
The issue is described here, with a nice testcase:
https://bugzilla.kernel.org/show_bug.cgi?id=192931
The problem is that shmat() calls do_mmap_pgoff() with MAP_FIXED, and
the address rounded down to 0. For the regular mmap case, the
protection mentioned above is that the kernel gets to generate the
address -- arch_get_unmapped_area() will always check for MAP_FIXED and
return that address. So by the time we do security_mmap_addr(0) things
get funky for shmat().
The testcase itself shows that while a regular user crashes, root will
not have a problem attaching a nil-page. There are two possible fixes
to this. The first, and which this patch does, is to simply allow root
to crash as well -- this is also regular mmap behavior, ie when hacking
up the testcase and adding mmap(... |MAP_FIXED). While this approach
is the safer option, the second alternative is to ignore SHM_RND if the
rounded address is 0, thus only having MAP_SHARED flags. This makes the
behavior of shmat() identical to the mmap() case. The downside of this
is obviously user visible, but does make sense in that it maintains
semantics after the round-down wrt 0 address and mmap.
Passes shm related ltp tests.
Link: http://lkml.kernel.org/r/1486050195-18629-1-git-send-email-dave@stgolabs.net
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Reported-by: Gareth Evans <gareth.evans@contextis.co.uk>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd8416c47715cf324c9a16f13273f9fda87acfed upstream.
With rw_page, page_endio is used for completing IO on a page and it
propagates write error to the address space if the IO fails. The
problem is it accesses page->mapping directly which might be okay for
file-backed pages but it shouldn't for anonymous page. Otherwise, it
can corrupt one of field from anon_vma under us and system goes panic
randomly.
swap_writepage
bdev_writepage
ops->rw_page
I encountered the BUG during developing new zram feature and it was
really hard to figure it out because it made random crash, somtime
mmap_sem lockdep, sometime other places where places never related to
zram/zsmalloc, and not reproducible with some configuration.
When I consider how that bug is subtle and people do fast-swap test with
brd, it's worth to add stable mark, I think.
Fixes: dd6bd0d9c7 ("swap: use bdev_read_page() / bdev_write_page()")
Signed-off-by: Minchan Kim <minchan@kernel.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e1587a4945408faa58d0485002c110eb2454740c upstream.
At the end of a window period, if the reclaimed pages is greater than
scanned, an unsigned underflow can result in a huge pressure value and
thus a critical event. Reclaimed pages is found to go higher than
scanned because of the addition of reclaimed slab pages to reclaimed in
shrink_node without a corresponding increment to scanned pages.
Minchan Kim mentioned that this can also happen in the case of a THP
page where the scanned is 1 and reclaimed could be 512.
Link: http://lkml.kernel.org/r/1486641577-11685-1-git-send-email-vinmenon@codeaurora.org
Signed-off-by: Vinayak Menon <vinmenon@codeaurora.org>
Acked-by: Minchan Kim <minchan@kernel.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Rik van Riel <riel@redhat.com>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Anton Vorontsov <anton.vorontsov@linaro.org>
Cc: Shiraz Hashim <shashim@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e02dc017c3032dcdce1b993af0db135462e1b4b7 upstream.
When @node_reclaim_node isn't 0, the page allocator tries to reclaim
pages if the amount of free memory in the zones are below the low
watermark. On Power platform, none of NUMA nodes are scanned for page
reclaim because no nodes match the condition in zone_allows_reclaim().
On Power platform, RECLAIM_DISTANCE is set to 10 which is the distance
of Node-A to Node-A. So the preferred node even won't be scanned for
page reclaim.
__alloc_pages_nodemask()
get_page_from_freelist()
zone_allows_reclaim()
Anton proposed the test code as below:
# cat alloc.c
:
int main(int argc, char *argv[])
{
void *p;
unsigned long size;
unsigned long start, end;
start = time(NULL);
size = strtoul(argv[1], NULL, 0);
printf("To allocate %ldGB memory\n", size);
size <<= 30;
p = malloc(size);
assert(p);
memset(p, 0, size);
end = time(NULL);
printf("Used time: %ld seconds\n", end - start);
sleep(3600);
return 0;
}
The system I use for testing has two NUMA nodes. Both have 128GB
memory. In below scnario, the page caches on node#0 should be reclaimed
when it encounters pressure to accommodate request of allocation.
# echo 2 > /proc/sys/vm/zone_reclaim_mode; \
sync; \
echo 3 > /proc/sys/vm/drop_caches; \
# taskset -c 0 cat file.32G > /dev/null; \
grep FilePages /sys/devices/system/node/node0/meminfo
Node 0 FilePages: 33619712 kB
# taskset -c 0 ./alloc 128
# grep FilePages /sys/devices/system/node/node0/meminfo
Node 0 FilePages: 33619840 kB
# grep MemFree /sys/devices/system/node/node0/meminfo
Node 0 MemFree: 186816 kB
With the patch applied, the pagecache on node-0 is reclaimed when its
free memory is running out. It's the expected behaviour.
# echo 2 > /proc/sys/vm/zone_reclaim_mode; \
sync; \
echo 3 > /proc/sys/vm/drop_caches
# taskset -c 0 cat file.32G > /dev/null; \
grep FilePages /sys/devices/system/node/node0/meminfo
Node 0 FilePages: 33605568 kB
# taskset -c 0 ./alloc 128
# grep FilePages /sys/devices/system/node/node0/meminfo
Node 0 FilePages: 1379520 kB
# grep MemFree /sys/devices/system/node/node0/meminfo
Node 0 MemFree: 317120 kB
Fixes: 5f7a75acdb ("mm: page_alloc: do not cache reclaim distances")
Link: http://lkml.kernel.org/r/1486532455-29613-1-git-send-email-gwshan@linux.vnet.ibm.com
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21e722c4c8377b5bc82ad058fed12165af739c1b upstream.
The check to set identity map for tylersburg is done too late. It needs
to be done before the check for identity_map domain is done.
To: Joerg Roedel <joro@8bytes.org>
To: David Woodhouse <dwmw2@infradead.org>
Cc: iommu@lists.linux-foundation.org
Cc: linux-kernel@vger.kernel.org
Cc: Ashok Raj <ashok.raj@intel.com>
Fixes: 86080ccc22 ("iommu/vt-d: Allocate si_domain in init_dmars()")
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Reported-by: Yunhong Jiang <yunhong.jiang@intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e42a46b6f52473661ad192f76a128a68fe301df4 upstream.
It is allowed to call regulator_get with a NULL dev argument
(_regulator_get explicitly checks for it) but this causes an error later
when printing /sys/kernel/debug/regulator_summary.
Fix this by explicitly handling "deviceless" consumers in the debugfs code.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e017006022abfea5d2466cad936065f45763ad1 upstream.
gcc-7 detects that wlanhdr_to_ethhdr() in two drivers calls memcpy() with
a destination argument that an earlier function call may have set to NULL:
staging/rtl8188eu/core/rtw_recv.c: In function 'wlanhdr_to_ethhdr':
staging/rtl8188eu/core/rtw_recv.c:1318:2: warning: argument 1 null where non-null expected [-Wnonnull]
staging/rtl8712/rtl871x_recv.c: In function 'r8712_wlanhdr_to_ethhdr':
staging/rtl8712/rtl871x_recv.c:649:2: warning: argument 1 null where non-null expected [-Wnonnull]
I'm fixing this by adding a NULL pointer check and returning failure
from the function, which is hopefully already handled properly.
This seems to date back to when the drivers were originally added,
so backporting the fix to stable seems appropriate. There are other
related realtek drivers in the kernel, but none of them contain a
function with a similar name or produce this warning.
Fixes: 1cc18a22b9 ("staging: r8188eu: Add files for new driver - part 5")
Fixes: 2865d42c78 ("staging: r8712u: Add the new driver to the mainline kernel")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29693efcea0f38cf40d0055d2401490a4f9bf8be upstream.
On this machine, the micmute button is connected to Line2 of the
codec and the micmute led is connected to GPIO2 of the codec.
After applying this quirk, both hotkey and led work well.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f3ac9f737603da80c2da3e84b89e74429836bb6d upstream.
The sequencer FIFO management has a bug that may lead to a corruption
(shortage) of the cell linked list. When a sequencer client faces an
error at the event delivery, it tries to put back the dequeued cell.
When the first queue was put back, this forgot the tail pointer
tracking, and the link will be screwed up.
Although there is no memory corruption, the sequencer client may stall
forever at exit while flushing the pending FIFO cells in
snd_seq_pool_done(), as spotted by syzkaller.
This patch addresses the missing tail pointer tracking at
snd_seq_fifo_cell_putback(). Also the patch makes sure to clear the
cell->enxt pointer at snd_seq_fifo_event_in() for avoiding a similar
mess-up of the FIFO linked list.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15c75b09f8d190f89ab4db463b87d411ca349dfe upstream.
Currently ctxfi driver tries to set only the 64bit DMA mask on 64bit
architectures, and bails out if it fails. This causes a problem on
some platforms since the 64bit DMA isn't always guaranteed. We should
fall back to the default 32bit DMA when 64bit DMA fails.
Fixes: 6d74b86d3c ("ALSA: ctxfi - Allow 64bit DMA")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 71321eb3f2d0df4e6c327e0b936eec4458a12054 upstream.
When a user sets a too small ticks with a fine-grained timer like
hrtimer, the kernel tries to fire up the timer irq too frequently.
This may lead to the condensed locks, eventually the kernel spinlock
lockup with warnings.
For avoiding such a situation, we define a lower limit of the
resolution, namely 1ms. When the user passes a too small tick value
that results in less than that, the kernel returns -EINVAL now.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7480b34ad1ab84a63540b2c884cb92c0764ab74 upstream.
Like for Sunrise Point, the total stream number of Lewisburg's
input and output stream exceeds 15 (GCAP is 0x9701), which will
cause some streams do not work because of the overflow on
SDxCTL.STRM field if using the legacy stream tag allocation method.
Fixes: 5cf92c8b3d ("ALSA: hda - Add Intel Lewisburg device IDs Audio")
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9f1bc2c4c58fcb2d86e0e26437dc8f3a18ac3276 upstream.
The issue is the same as "dd9aa335c880 ALSA: hda/realtek - Can't adjust
speaker's volume on a Dell AIO", the output requires to connect to a node
with Amp-out capability.
Applying the same fixup "ALC298_FIXUP_SPK_VOLUME" can fix the issue.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 78162d48466d23c45a784034630c5928af631e3d upstream.
Enable DMA on uart1 to get a more reliable console.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef8d02d4a2c36f7a93e74c95a9c419353b310117 upstream.
Enable DMA on usart3 to get a more reliable console. This is especially
useful for automation and kernelci were a kernel with PROVE_LOCKING enabled
is quite susceptible to character loss, resulting in tests failure.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ebf75774f823ddbdbd10921006989d4df222f4a upstream.
In vpfe_s_fmt(), when the sensor format and the requested format were
the same, bpp was assigned to vpfe->bpp without being initialized first.
Grab the bpp value that is currently used by using __vpfe_get_format()
instead of its wrapper, vpfe_try_fmt().
This use of uninitialized variable has been found by compiling the
kernel with clang.
Fixes: 417d2e507e ("[media] media: platform: add VPFE capture driver
support for AM437X")
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 096a0de427ea333f56f0ee00328cff2a2731bcf1 upstream.
is_jump_ins() checks for plain jump ("j") instructions since commit
e7438c4b89 ("MIPS: Fix sibling call handling in get_frame_info") but
that commit didn't make the same change to the microMIPS code, leaving
it inconsistent with the MIPS32/MIPS64 code. Handle the microMIPS
encoding of the jump instruction too such that it behaves consistently.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: e7438c4b89 ("MIPS: Fix sibling call handling in get_frame_info")
Cc: Tony Wu <tung7970@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14533/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb9bc4689b9c635714fbcd5d335bad9934a7ebfc upstream.
get_frame_info() calculates the offset of the return address within a
stack frame simply by dividing a the bottom 16 bits of the instruction,
treated as a signed integer, by the size of a long. Whilst this works
for MIPS32 & MIPS64 ISAs where the sw or sd instructions are used, it's
incorrect for microMIPS where encodings differ. The result is that we
typically completely fail to unwind the stack on microMIPS.
Fix this by adjusting is_ra_save_ins() to calculate the return address
offset, and take into account the various different encodings there in
the same place as we consider whether an instruction is storing the
ra/$31 register.
With this we are now able to unwind the stack for kernels targetting the
microMIPS ISA, for example we can produce:
Call Trace:
[<80109e1f>] show_stack+0x63/0x7c
[<8011ea17>] __warn+0x9b/0xac
[<8011ea45>] warn_slowpath_fmt+0x1d/0x20
[<8013fe53>] register_console+0x43/0x314
[<8067c58d>] of_setup_earlycon+0x1dd/0x1ec
[<8067f63f>] early_init_dt_scan_chosen_stdout+0xe7/0xf8
[<8066c115>] do_early_param+0x75/0xac
[<801302f9>] parse_args+0x1dd/0x308
[<8066c459>] parse_early_options+0x25/0x28
[<8066c48b>] parse_early_param+0x2f/0x38
[<8066e8cf>] setup_arch+0x113/0x488
[<8066c4f3>] start_kernel+0x57/0x328
---[ end trace 0000000000000000 ]---
Whereas previously we only produced:
Call Trace:
[<80109e1f>] show_stack+0x63/0x7c
---[ end trace 0000000000000000 ]---
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: 34c2f668d0 ("MIPS: microMIPS: Add unaligned access support.")
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14532/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6c7a324df37bf05ef7a2c1580683cf10d082d97 upstream.
get_frame_info() is meant to iterate over up to the first 128
instructions within a function, but for microMIPS kernels it will not
reach that many instructions unless the function is 512 bytes long since
we calculate the maximum number of instructions to check by dividing the
function length by the 4 byte size of a union mips_instruction. In
microMIPS kernels this won't do since instructions are variable length.
Fix this by instead checking whether the pointer to the current
instruction has reached the end of the function, and use max_insns as a
simple constant to check the number of iterations against.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: 34c2f668d0 ("MIPS: microMIPS: Add unaligned access support.")
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14530/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a3552dace7d1d0cabf573e88fc3025cb90c4a601 upstream.
During stack unwinding we call a number of functions to determine what
type of instruction we're looking at. The union mips_instruction pointer
provided to them may be pointing at a 2 byte, but not 4 byte, aligned
address & we thus cannot directly access the 4 byte wide members of the
union mips_instruction. To avoid this is_ra_save_ins() copies the
required half-words of the microMIPS instruction to a correctly aligned
union mips_instruction on the stack, which it can then access safely.
The is_jump_ins() & is_sp_move_ins() functions do not correctly perform
this temporary copy, and instead attempt to directly dereference 4 byte
fields which may be misaligned and lead to an address exception.
Fix this by copying the instruction halfwords to a temporary union
mips_instruction in get_frame_info() such that we can provide a 4 byte
aligned union mips_instruction to the is_*_ins() functions and they do
not need to deal with misalignment themselves.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: 34c2f668d0 ("MIPS: microMIPS: Add unaligned access support.")
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14529/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
