Since commit 9e13f345 (ASoC: sgtl5000: Let the codec acquire its clock) , the
'clocks' entry is mandatory, so update the binding doc.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add DT bindings for the gpio-rcar driver and read the device
configuration from the DT node at probe time if available.
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the possibility to get the clock-frequency from a timer clock instead
of specifying it as dt property. Additionally also add the possibility
to also define a controlling periphal clock for the timer block.
The clock-frequency property is kept to act as fallback if no clocks
are specified.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Add pwm driver for the NXP pca9685 16 channel pwm-led controller.
The driver is really barebones at this stage. E.g. the OE' pin and
therefore the corresponding registers are not supported.
The driver was tested on a HW where this pin is tied to GND.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
[thierry.reding@gmail.com: style and whitespace cleanups]
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add the various binding files for the palmas family of chips. There is a
top level MFD binding then a seperate binding for regulators IP blocks on chips.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Signed-off-by: Ian Lartey <ian@slimlogic.co.uk>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
From Alexander Shiyan, this is a series of cleanups of clps711x, movig it
closer to multiplatform and cleans up a bunch of old code.
* clps711x/soc:
ARM: clps711x: Update defconfig
ARM: clps711x: Add support for SYSCON driver
ARM: clps711x: edb7211: Control LCD backlight via PWM
ARM: clps711x: edb7211: Add support for I2C
ARM: clps711x: Optimize interrupt handling
ARM: clps711x: Add clocksource framework
ARM: clps711x: Replace "arch_initcall" in common code with ".init_early"
ARM: clps711x: Move specific definitions from hardware.h to boards files
ARM: clps711x: p720t: Define PLD registers as GPIOs
ARM: clps711x: autcpu12: Move remaining specific definitions to board file
ARM: clps711x: autcpu12: Special driver for handling memory is removed
ARM: clps711x: autcpu12: Add support for NOR flash
ARM: clps711x: autcpu12: Move LCD DPOT definitions to board file
ARM: clps711x: Set PLL clock to zero if we work from 13 mHz source
ARM: clps711x: Remove NEED_MACH_MEMORY_H dependency
ARM: clps711x: Re-add GPIO support
GPIO: clps711x: Add DT support
GPIO: clps711x: Rewrite driver for using generic GPIO code
+ Linux 3.10-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
Add DT support to the CLPS711X GPIO driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
There is no users of this code and there is already a pinctrl
driver written for s3c24xx which is going to be used on any
s3c24xx DT platforms. Hence this has been effectively a dead
code in mainline.
This reverts commit 172c6a1365
gpio: samsung: add devicetree init for s3c24xx arches
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add G2D clocks for Exynos4x12 SoC and sclk_fimg2d required by G2D
IP.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The exynos5-dp node needs a clock specified using the common clock
framework.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for the AD7303. The AD7303 is a simple 2 channel 8 bit
DAC with an SPI interface.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds an irqchip driver for the main interrupt controller found
on Marvell Orion SoCs (Kirkwood, Dove, Orion5x, Discovery Innovation).
Corresponding device tree documentation is also added.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/1370536034-23956-2-git-send-email-sebastian.hesselbarth@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Document device tree binding information as required by the
Samsung' USB 3.0 controller.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Per review feedback from Lars-Peter Clausen <lars@metafoo.de>
Changes since V1:
Fix return value handling of adf4350_parse_dt()
Use of_get_gpio
Avoid abbreviations in devicetree properties
Fix typo in docs
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add Freescale lpuart driver support. The lpuart device
can be found on Vybrid VF610 and Layerscape LS-1 SoCs.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Document the device tree binding for the WM8962 codec, and modify the
driver to extract platform data from the device tree, if present.
Based on work of WM8903 by Stephen Warren <swarren@nvidia.com>
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The interrupt and charging parameters are configurable in the device tree
structure. In the board test, a GPIO is used for handling LP8727
interrupts. The device tree binding documentation is added also.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Highbank supports SGPIO by bit-banging out the SGPIO signals over
three GPIO pins defined in the DTB. Add support for this SGPIO
functionality.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch adds a clocksource/clockevent driver for the timer found on some
models in the TI-Nspire calculator series. The timer has two 16bit subtimers
within its memory mapped I/O interface but only the first can generate
interrupts. The first subtimer is used to generate clockevents but only if an
interrupt number and register is given.
The interrupt acknowledgement mechanism is a little strange because the
interrupt mask and acknowledge registers are located in another memory mapped
I/O peripheral. The address of this register is passed to the driver through
device tree bindings.
The second subtimer is used as a clocksource because it isn't capable of
generating an interrupt. This subtimer is always added.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Tang <dt.tangr@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Merge 'net' bug fixes into 'net-next' as we have patches
that will build on top of them.
This merge commit includes a change from Emil Goode
(emilgoode@gmail.com) that fixes a warning that would
have been introduced by this merge. Specifically it
fixes the pingv6_ops method ipv6_chk_addr() to add a
"const" to the "struct net_device *dev" argument and
likewise update the dummy_ipv6_chk_addr() declaration.
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding phy-mode support to cpsw driver and updating the cpsw binding
documentation.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compatible list is used in commit 03b1781 but is not documented.
Add necessary device tree bindings to describe on-chip UFS host
controllers.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This is a driver for the keypads found on the TI-Nspire series calculators.
Signed-off-by: Daniel Tang <dt.tangr@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some platforms have channels which are not available for normal use.
This information is currently passed though platform data in internal
BSP kernels. Once those platforms land, they'll need to configure them
appropriately, so we may as well add the infrastructure.
Cc: Dan Williams <djbw@fb.com>
Cc: Per Forlin <per.forlin@stericsson.com>
Cc: Rabin Vincent <rabin@rab.in>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
At this moment in time the memcpy channels which can be used by the D40
are fixed, as each supported platform in Mainline uses the same ones.
However, platforms do exist which don't follow this convention, so
these will need to be tailored. Fortunately, these platforms will be DT
only, so this change has very little impact on platform data.
Cc: Dan Williams <djbw@fb.com>
Cc: Per Forlin <per.forlin@stericsson.com>
Cc: Rabin Vincent <rabin@rab.in>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch will allow ux500-musb to be probed and configured solely from
configuration found in Device Tree.
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: linux-usb@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The uart works in the DCE mode by default, but sometime we need it
works at the DTE mode.
This patch adds the support for the DTE mode.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Throw in a file with references to the IEEE binding documents.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
From Nicolas Pitre:
This is the first MCPM backend submission for VExpress running on RTSM
aka Fast Models implementing the big.LITTLE system architecture. This
enables SMP secondary boot as well as CPU hotplug on this platform.
A big prerequisite for this support is the CCI driver from Lorenzo
included in this pull request.
Also included is Rob Herring's set_auxcr/get_auxcr allowing nicer code.
Signed-off-by: Olof Johansson <olof@lixom.net>
* 'VExpress_DCSCB' of git://git.linaro.org/people/nico/linux:
ARM: vexpress: Select multi-cluster SMP operation if required
ARM: vexpress/dcscb: handle platform coherency exit/setup and CCI
ARM: vexpress/dcscb: do not hardcode number of CPUs per cluster
ARM: vexpress/dcscb: add CPU use counts to the power up/down API implementation
ARM: vexpress: introduce DCSCB support
ARM: introduce common set_auxcr/get_auxcr functions
drivers/bus: arm-cci: function to enable CCI ports from early boot code
drivers: bus: add ARM CCI support
- kirkwood
- enable pcie driver
- migrate boards over to pcie dt init
depends
- mvebu/pcie
- mvebu/of_pci
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRpP1WAAoJEAi3KVZQDZAeItIH/1QVHhqYSpOnXGu4zQHswvIM
SRQoy4hiCJm+yywTnIDJPMQdBKD1vURRRdGWQouNsFoBaHki4v2BBxfBNFoDN+rx
VtECH7F1SbJ/Pb7XLVnswqRXVNqrY5fOY5mW42ALFBT9VxcKoD1FyqCaXfaU9JA4
VQCzR7DjFhr8bppZknQ5ZT/qI66Wj1oNiJtBdItmxT0pVfElvAOV6FHzfMGrrDrM
+v8T8KdFIdmH1Ny5J5KLQSE9qBLqae0vlDNgsfwfh1DY/Lye3rDHqPDKrh7YZjHR
xNc6JU+zEdP3tK1f1jgmjn/giY7HqpAFm46p9k/pF9gsE5SE0L/e0Dh9apOcq24=
=qUyf
-----END PGP SIGNATURE-----
Merge tag 'pcie_kw-3.11' of git://git.infradead.org/users/jcooper/linux into next/soc
From Jason Cooper:
mvebu pcie driver (kirkwood) for v3.11
- kirkwood
- enable pcie driver
- migrate boards over to pcie dt init
depends
- mvebu/pcie
- mvebu/of_pci
Signed-off-by: Olof Johansson <olof@lixom.net>
* tag 'pcie_kw-3.11' of git://git.infradead.org/users/jcooper/linux:
arm: kirkwood: convert db-88f6281/db-88f6282 to the Device Tree
arm: kirkwood: convert QNAP TS219 to use DT for the PCIe interface
arm: kirkwood: convert ZyXEL NSA310 to use DT for the PCIe interface
arm: kirkwood: convert MPL CEC4 to use DT for the PCIe interface
arm: kirkwood: convert Iomega Iconnect to use DT for the PCIe interface
arm: kirkwood: add SoC-level Device Tree data for PCIe interfaces
arm: kirkwood: move PCIe window init to legacy driver
pci: mvebu: enable driver usage on Kirkwood
- mvebu pcie
- fix return value check in mvebu_pcie_probe()
depends
- mvebu/of_pci
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRpPzyAAoJEAi3KVZQDZAeuf0H/2FsmnLgvJh24z1B1HLuWm52
TYgoORahPsuoP7L2RZBU6n3++UuX4NGbVcagqRDe1Asou0oG0fu6oXbdn0d4avff
hoIuRq3LWhQ6DYaeV34vV8vM8x79HYM7FT92zX7VZKJ6TL6KGSHHSvVKhqWo7y65
++Ogtl5hzjyMzcQo5LoDQ+bqVLZpbfF7D/dreCCzzmlODqCNZGoBeZOwTqyR9kDW
aO65yDcsFIky2YAGz+uT0ItNpAtGzshJU/d6QTHNlvKeae2NjMqv2X7hP4161uQ4
NGyCsm7Aif5WnBQGQsvgCIPnuxTaYaGOSZQLMG7pN7TJQgx0sgF93HmX/gUI/WQ=
=ye72
-----END PGP SIGNATURE-----
Merge tag 'pcie-3.11-2' of git://git.infradead.org/users/jcooper/linux into next/soc
PCI-e driver for mvebu.
* tag 'pcie-3.11-2' of git://git.infradead.org/users/jcooper/linux:
pci: mvebu: fix return value check in mvebu_pcie_probe()
arm: mvebu: PCIe support is now available on mvebu
pci: PCIe driver for Marvell Armada 370/XP systems
clk: mvebu: add more PCIe clocks for Armada XP
clk: mvebu: create parent-child relation for PCIe clocks on Armada 370
of/pci: Add of_pci_parse_bus_range() function
of/pci: Add of_pci_get_devfn() function
of/pci: Provide support for parsing PCI DT ranges property
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds a separate driver for the MDIO interface of the
Allwinner ethernet controllers.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Allwinner A10 has an ethernet controller that seem to be developped
internally by them.
The exact feature set of this controller is unknown, since there is no
public documentation for this IP, and this driver is mostly the one
published by Allwinner that has been heavily cleaned up.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a basic clock driver for the TI-Nspire calculator
series.
Changes from v1:
* Removed filename in header comment
* Removed unnecessary #undef EXTRACT statement
Signed-off-by: Daniel Tang <dt.tangr@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
[mturquette@linaro.org: fixed $SUBJECT and changelog max width]
This adds support for probing the COH 901 327 watchdog from
the device tree and also adds associated bindings.
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds device tree support for the ST DDC I2C driver known
as "stu300" in the kernel tree.
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes it possible to probe the COH901 pinctrl driver from
the device tree, and assigned the device tree node in the
gpio_chip so we can look up cross-references from the device
tree. Start grabbing the per-port (bank) IRQs by index instead
of by name so we don't have to look up the IRQs by name going
forward.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds device tree support for the U300 timer, by making
the memory base offset and IRQ dynamically assigned, then
optionally looking them up from the device tree.
Since the timer needs to be registered before any platform
devices are created, we will go into the device tree and look
up the "/timer@c0014000" node and read our base address and
IRQ from there.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds device tree parsing support for the shared driver of mv643xx_eth.
As the bindings are slightly different from current PPC bindings new binding
documentation is also added. Following PPC-style device setup, the shared
driver now also adds port platform_devices and sets up port platform_data.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add a property 'disabled-ports' representing the unused port
of USB3503. USB3503 can support up to 3 USB host port and each ports can be
controlled to be enabled or disabled. Do not describe this property if all
ports must be enabled.
You can represent the ports to disable in the device tree.
usb3503@08{
...
disabled-ports = <2 3>;
...
};
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Tegra USB bindings were in bad shape. The patches in this branch
fix the binding definitions, and make all the necessary additions to
the DT files. Stale nodes/properties will be removed early in 3.12
once the USB driver has been updated for the new binding.
These changes are needed in both the USB tree, to allow the driver to
be updated to handle them, and the Tegra tree, so that various tree-
wide DT changes (e.g. conversion of IRQ/GPIO/clock constants to defines)
can be applied on top of them.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=fg0r
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.11-deps-for-usb' into next
ARM: tegra: DT-related fixes needed by the USB tree
The Tegra USB bindings were in bad shape. The patches in this branch
fix the binding definitions, and make all the necessary additions to
the DT files. Stale nodes/properties will be removed early in 3.12
once the USB driver has been updated for the new binding.
These changes are needed in both the USB tree, to allow the driver to
be updated to handle them, and the Tegra tree, so that various tree-
wide DT changes (e.g. conversion of IRQ/GPIO/clock constants to defines)
can be applied on top of them.
* tag 'tegra-for-3.11-deps-for-usb':
ARM: tegra: update device trees for USB binding rework
ARM: tegra: modify ULPI reset GPIO properties
ARM: tegra: finalize USB EHCI and PHY bindings
Signed-of-by: Felipe Balbi <balbi@ti.com>
