App type is required to send the calibration
for the modules in a topology that would
be selected for ULLPP. For this, expose
a mixer control. App type will be sent
if the ULLPP is used for NOIRQ.
CRs-Fixed: 2009687
Change-Id: I7c8349d5827dffe32c0db35262d54cb7c1dba1a9
Signed-off-by: Alexy Joseph <alexyj@codeaurora.org>
The initialization code in battery.c creates important votables like
FCC, FV which every many other charging drivers are dependent on.
The dependent charging drivers keep probe deferring until the votables
are created.
Ensure that battery.c's initialization code is invoked before other
drivers get added.
Change-Id: I52990baef7f7c4095e635728511e120c1dbe5e9d
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Remove the orig_addr_limit check against KERNEL_DS in
do_page_fault handler for permissions faults. This
check is part of UAO and PAN features and these features
are disabled by default.
Change-Id: I5de760b983edcf14d1c0bee2a53dc091ceca31da
Signed-off-by: Prasad Sodagudi <psodagud@codeaurora.org>
In case of USBIN-USBIN based parallel charging configuration
hardware based INOV is disabled and adapter output voltage of
QC3.0 adapter is controlled by userspace daemon. But in case
of QC 2.0 based adapter there is no such daemon to control
adapter output voltage, thus force 9V adapter output when a
QC 2.0 adapter is detected.
While at it, cancel icl_change_work before scheduling it in
order to make sure work is scheduled for next interval.
CRs-Fixed: 2015927
Change-Id: I198f8299b5cd0a62c518815c33088bb5e38c8505
Signed-off-by: Ashay Jaiswal <ashayj@codeaurora.org>
PM660 support configurable delay for softstart done with
minimum value of 3msec and thus OTG can be configured to
a minimum value till softstart completes. Add a PM660
specific workaround to set OTG current limit to 250mA before
enabling OTG mode and reconfigure the current back to desired
value once OTG softstart completes.
CRs-Fixed: 2016131
Change-Id: Iabb9e1c55cc59453825795e045d7fcc6caf8f33e
Signed-off-by: Ashay Jaiswal <ashayj@codeaurora.org>
Some FS devices report maxpacket size as 4 for their BULK EPs
which is incorrect as per USB specification. This results in
ep_config command to controller timing out and enumeration fails.
As minimum maxpacket size for FS is 8, override the same for such
devices.
CRs-fixed: 1002876
Change-Id: I70c2210b4eb93f557eef306fcbc11308b7b33e07
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Replenish trigger threshold for LAN_CONS is calculated
before updating the rx_pool_sz. This can result into
division by 0 which can make the system unstable.
Make a change to update the rx_pool_sz before updating
the replenish trigger threshold.
Change-Id: I62f6c114ce7aee571833ef05146ab75cab0fb5d2
Acked-by: Chaitanya Pratapa <cpratapa@qti.qualcomm.com>
Signed-off-by: Utkarsh Saxena <usaxena@codeaurora.org>
Update the bandwidth check for those cases where only
ab changes and ib is greater than ab. The current
logic takes the max of both and since ib is max, the
vote will not kick-in. This change is intended to
solve this problem.
Change-Id: Icbd6d9aa5221784bc1c88ae1965c944503ac78dc
Signed-off-by: Ingrid Gallardo <ingridg@codeaurora.org>
Separate out the aggre2_noc voters so that individual voters could vote on
these clocks and voter clock would aggregate the clock rates before sending
a request to RPM.
Change-Id: I8ef30af257d2f37ec5af6aa5e3d1b69e5ba8ec8c
Signed-off-by: Taniya Das <tdas@codeaurora.org>
This change on arrival of ssr event schdule a worker thread,
which when run carry out task of qmi handle destruction.
It is a desired change to make ssr notification callback as
light as possible and avoid blocking it for long in corner cases.
Change-Id: I832fabce7569b1b8b966b7c49cda1b00cff2c472
Signed-off-by: Avaneesh Kumar Dwivedi <akdwived@codeaurora.org>
Commit b953b45ed08c ("USB: composite: Release spinlock before
WARN()") introduced a bug where it leads to calling spin_unlock_
irq_save twice in case of delayed_status zero. Hence fix the issue
by returning from composite_setup_continue() right after WARN() in
case of delayed_status zero.
Change-Id: I33c77ec8a2f97fcd94cffb416e57f3c77d6789f2
Signed-off-by: Vijayavardhan Vennapusa <vvreddy@codeaurora.org>
The wlan firmware is configuring the clk and voltage regulator
for hardware power on and hardware reset sequence.
The icnss platform driver is configuring this clk and regulators
to avoid invalid access to copy engine register during the wlan
recovery.
As platform driver is not configuring this regulator to power on
or reset the WLAN hardware, So no need to define the voltage
regulators are the required properties for the ICNSS platform driver.
Define vdd-0.8-cx-mx as an optional voltage regulator for
the icnss platform driver.
CRs-Fixed: 2014965
Change-Id: I74a1445522997ba4e7a52da5a29e9afb57ad12df
Signed-off-by: Sarada Prasanna Garnayak <sgarna@codeaurora.org>
As GPIO 54 has already been connected to an external
pull up resistor, config it to no pull to save power
consumption.
CRs-Fixed: 2015121
Change-Id: Id13588be53b8756e4d9792035bcc6adfbaa8c3f7
Signed-off-by: xiaonian <xiaonian@codeaurora.org>
Add backend user count checking to protect the index
boundary.
Change-Id: Ic1b61d1f7130252cc54da0b16553858714988dbd
CRs-Fixed: 2009216
Signed-off-by: Walter Yang <yandongy@codeaurora.org>
Mark AIF4 MAD TX as ignore suspend so that MAD path
will not power down during suspend mode.
CRs-Fixed: 2003858
Change-Id: Iae55e2778edcdd8efa6ae13b746795d8a1594a41
Signed-off-by: Walter Yang <yandongy@codeaurora.org>
