[ Upstream commit e4849aff1e169b86c561738daf8ff020e9de1011 ]
The Broadcom SiByte BCM1250, BCM1125, and BCM1125H SOCs have an onchip
DRAM controller that supports memory amounts of up to 16GiB, and due to
how the address decoder has been wired in the SOC any memory beyond 1GiB
is actually mapped starting from 4GiB physical up, that is beyond the
32-bit addressable limit[1]. Consequently if the maximum amount of
memory has been installed, then it will span up to 19GiB.
Many of the evaluation boards we support that are based on one of these
SOCs have their memory soldered and the amount present fits in the
32-bit address range. The BCM91250A SWARM board however has actual DIMM
slots and accepts, depending on the peripherals revision of the SOC, up
to 4GiB or 8GiB of memory in commercially available JEDEC modules[2].
I believe this is also the case with the BCM91250C2 LittleSur board.
This means that up to either 3GiB or 7GiB of memory requires 64-bit
addressing to access.
I believe the BCM91480B BigSur board, which has the BCM1480 SOC instead,
accepts at least as much memory, although I have no documentation or
actual hardware available to verify that.
Both systems have PCI slots installed for use by any PCI option boards,
including ones that only support 32-bit addressing (additionally the
32-bit PCI host bridge of the BCM1250, BCM1125, and BCM1125H SOCs limits
addressing to 32-bits), and there is no IOMMU available. Therefore for
PCI DMA to work in the presence of memory beyond enable swiotlb for the
affected systems.
All the other SOC onchip DMA devices use 40-bit addressing and therefore
can address the whole memory, so only enable swiotlb if PCI support and
support for DMA beyond 4GiB have been both enabled in the configuration
of the kernel.
This shows up as follows:
Broadcom SiByte BCM1250 B2 @ 800 MHz (SB1 rev 2)
Board type: SiByte BCM91250A (SWARM)
Determined physical RAM map:
memory: 000000000fe7fe00 @ 0000000000000000 (usable)
memory: 000000001ffffe00 @ 0000000080000000 (usable)
memory: 000000000ffffe00 @ 00000000c0000000 (usable)
memory: 0000000087fffe00 @ 0000000100000000 (usable)
software IO TLB: mapped [mem 0xcbffc000-0xcfffc000] (64MB)
in the bootstrap log and removes failures like these:
defxx 0000:02:00.0: dma_direct_map_page: overflow 0x0000000185bc6080+4608 of device mask ffffffff bus mask 0
fddi0: Receive buffer allocation failed
fddi0: Adapter open failed!
IP-Config: Failed to open fddi0
defxx 0000:09:08.0: dma_direct_map_page: overflow 0x0000000185bc6080+4608 of device mask ffffffff bus mask 0
fddi1: Receive buffer allocation failed
fddi1: Adapter open failed!
IP-Config: Failed to open fddi1
when memory beyond 4GiB is handed out to devices that can only do 32-bit
addressing.
This updates commit cce335ae47 ("[MIPS] 64-bit Sibyte kernels need
DMA32.").
References:
[1] "BCM1250/BCM1125/BCM1125H User Manual", Revision 1250_1125-UM100-R,
Broadcom Corporation, 21 Oct 2002, Section 3: "System Overview",
"Memory Map", pp. 34-38
[2] "BCM91250A User Manual", Revision 91250A-UM100-R, Broadcom
Corporation, 18 May 2004, Section 3: "Physical Description",
"Supported DRAM", p. 23
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
[paul.burton@mips.com: Remove GPL text from dma.c; SPDX tag covers it]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Patchwork: https://patchwork.linux-mips.org/patch/21108/
References: cce335ae47 ("[MIPS] 64-bit Sibyte kernels need DMA32.")
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 347a28b586802d09604a149c1a1f6de5dccbe6fa ]
This happened while running in qemu-system-aarch64, the AMBA PL011 UART
driver when enabling CONFIG_DEBUG_TEST_DRIVER_REMOVE.
arch_initcall(pl011_init) came before subsys_initcall(default_bdi_init),
devtmpfs' handle_remove() crashes because the reference count is a NULL
pointer only because wb->bdi hasn't been initialized yet.
Rework so that wb_put have an extra check if wb->bdi before decrement
wb->refcnt and also add a WARN_ON_ONCE to get a warning if it happens again
in other drivers.
Fixes: 52ebea749a ("writeback: make backing_dev_info host cgroup-specific bdi_writebacks")
Co-developed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1f65b0d70e9e5c80e15105cd96fa00174d7c436 ]
It seems with some NICs supported by the e1000e driver a SYSTIM reading
may occasionally be few microseconds before the previous reading and if
enabled also pass e1000e_sanitize_systim() without reaching the maximum
number of rereads, even if the function is modified to check three
consecutive readings (i.e. it doesn't look like a double read error).
This causes an underflow in the timecounter and the PHC time jumps hours
ahead.
This was observed on 82574, I217 and I219. The fastest way to reproduce
it is to run a program that continuously calls the PTP_SYS_OFFSET ioctl
on the PHC.
Modify e1000e_phc_gettime() to use timecounter_cyc2time() instead of
timecounter_read() in order to allow non-monotonic SYSTIM readings and
prevent the PHC from jumping.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78f3ac76d9e5219589718b9e4733bee21627b3f5 ]
In the past, Asus firmwares would change the panel backlight directly
through the EC when the display off hotkey (Fn+F7) was pressed, and
only notify the OS of such change, with 0x33 when the LCD was ON and
0x34 when the LCD was OFF. These are currently mapped to
KEY_DISPLAYTOGGLE and KEY_DISPLAY_OFF, respectively.
Most recently the EC on Asus most machines lost ability to toggle the
LCD backlight directly, but unless the OS informs the firmware it is
going to handle the display toggle hotkey events, the firmware still
tries change the brightness through the EC, to no effect. The end result
is a long list (at Endless we counted 11) of Asus laptop models where
the display toggle hotkey does not perform any action. Our firmware
engineers contacts at Asus were surprised that there were still machines
out there with the old behavior.
Calling WMNB(ASUS_WMI_DEVID_BACKLIGHT==0x00050011, 2) on the _WDG device
tells the firmware that it should let the OS handle the display toggle
event, in which case it will simply notify the OS of a key press with
0x35, as shown by the DSDT excerpts bellow.
Scope (_SB)
{
(...)
Device (ATKD)
{
(...)
Name (_WDG, Buffer (0x28)
{
/* 0000 */ 0xD0, 0x5E, 0x84, 0x97, 0x6D, 0x4E, 0xDE, 0x11,
/* 0008 */ 0x8A, 0x39, 0x08, 0x00, 0x20, 0x0C, 0x9A, 0x66,
/* 0010 */ 0x4E, 0x42, 0x01, 0x02, 0x35, 0xBB, 0x3C, 0x0B,
/* 0018 */ 0xC2, 0xE3, 0xED, 0x45, 0x91, 0xC2, 0x4C, 0x5A,
/* 0020 */ 0x6D, 0x19, 0x5D, 0x1C, 0xFF, 0x00, 0x01, 0x08
})
Method (WMNB, 3, Serialized)
{
CreateDWordField (Arg2, Zero, IIA0)
CreateDWordField (Arg2, 0x04, IIA1)
Local0 = (Arg1 & 0xFFFFFFFF)
(...)
If ((Local0 == 0x53564544))
{
(...)
If ((IIA0 == 0x00050011))
{
If ((IIA1 == 0x02))
{
^^PCI0.SBRG.EC0.SPIN (0x72, One)
^^PCI0.SBRG.EC0.BLCT = One
}
Return (One)
}
}
(...)
}
(...)
}
(...)
}
(...)
Scope (_SB.PCI0.SBRG.EC0)
{
(...)
Name (BLCT, Zero)
(...)
Method (_Q10, 0, NotSerialized) // _Qxx: EC Query
{
If ((BLCT == Zero))
{
Local0 = One
Local0 = RPIN (0x72)
Local0 ^= One
SPIN (0x72, Local0)
If (ATKP)
{
Local0 = (0x34 - Local0)
^^^^ATKD.IANE (Local0)
}
}
ElseIf ((BLCT == One))
{
If (ATKP)
{
^^^^ATKD.IANE (0x35)
}
}
}
(...)
}
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7b38460dc8e4eafba06c78f8e37099d3b34d473c upstream.
Kanda Motohiro reported that expanding a tiny xattr into a large xattr
fails on XFS because we remove the tiny xattr from a shortform fork and
then try to re-add it after converting the fork to extents format having
not removed the ATTR_REPLACE flag. This fails because the attr is no
longer present, causing a fs shutdown.
This is derived from the patch in his bug report, but we really
shouldn't ignore a nonzero retval from the remove call.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199119
Reported-by: kanda.motohiro@gmail.com
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d4a7e9bb74b5aaf07b89f6531c080b1130bdf019 ]
I realized the last patch calls dev_get_by_index_rcu in a branch not
holding the rcu lock. Add the calls to rcu_read_lock and rcu_read_unlock.
Fixes: ec90ad334986 ("ipv6: Consider sk_bound_dev_if when binding a socket to a v4 mapped address")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ec90ad334986fa5856d11dd272f7f22fa86c55c4 ]
Similar to c5ee066333eb ("ipv6: Consider sk_bound_dev_if when binding a
socket to an address"), binding a socket to v4 mapped addresses needs to
consider if the socket is bound to a device.
This problem also exists from the beginning of git history.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 36352991835ce99e46b4441dd0eb6980f9a83e8f ]
There are two new Realtek Ethernet devices which are re-branded r8168h.
Add the IDs to to support them.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c06ef2e9acef4cda1feee2ce055b8086e33d251a upstream.
As reported by smatch:
drivers/media/common/videobuf2/videobuf2-core.c: drivers/media/common/videobuf2/videobuf2-core.c:2159 vb2_mmap() warn: inconsistent returns 'mutex:&q->mmap_lock'.
Locked on: line 2148
Unlocked on: line 2100
line 2108
line 2113
line 2118
line 2156
line 2159
There is one error condition that doesn't unlock a mutex.
Fixes: cd26d1c4d1bc ("media: vb2: vb2_mmap: move lock up")
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66a8d5bfb518f9f12d47e1d2dce1732279f9451e upstream.
Strict requirement of pixclock to be zero breaks support of SDL 1.2
which contains hardcoded table of supported video modes with non-zero
pixclock values[1].
To better understand which pixclock values are considered valid and how
driver should handle these values, I briefly examined few existing fbdev
drivers and documentation in Documentation/fb/. And it looks like there
are no strict rules on that and actual behaviour varies:
* some drivers treat (pixclock == 0) as "use defaults" (uvesafb.c);
* some treat (pixclock == 0) as invalid value which leads to
-EINVAL (clps711x-fb.c);
* some pass converted pixclock value to hardware (uvesafb.c);
* some are trying to find nearest value from predefined table
(vga16fb.c, video_gx.c).
Given this, I believe that it should be safe to just ignore this value if
changing is not supported. It seems that any portable fbdev application
which was not written only for one specific device working under one
specific kernel version should not rely on any particular behaviour of
pixclock anyway.
However, while enabling SDL1 applications to work out of the box when
there is no /etc/fb.modes with valid settings, this change affects the
video mode choosing logic in SDL. Depending on current screen
resolution, contents of /etc/fb.modes and resolution requested by
application, this may lead to user-visible difference (not always):
image will be displayed in a right way, but it will be aligned to the
left instead of center. There is no "right behaviour" here as well, as
emulated fbdev, opposing to old fbdev drivers, simply ignores any
requsts of video mode changes with resolutions smaller than current.
The easiest way to reproduce this problem is to install sdl-sopwith[2],
remove /etc/fb.modes file if it exists, and then try to run sopwith
from console without X. At least in Fedora 29, sopwith may be simply
installed from standard repositories.
[1] SDL 1.2.15 source code, src/video/fbcon/SDL_fbvideo.c, vesa_timings
[2] http://sdl-sopwith.sourceforge.net/
Signed-off-by: Ivan Mironov <mironov.ivan@gmail.com>
Cc: stable@vger.kernel.org
Fixes: 79e539453b ("DRM: i915: add mode setting support")
Fixes: 771fe6b912 ("drm/radeon: introduce kernel modesetting for radeon hardware")
Fixes: 785b93ef8c ("drm/kms: move driver specific fb common code to helper functions (v2)")
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190108072353.28078-3-mironov.ivan@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 628bd85947091830a8c4872adfd5ed1d515a9cf2 upstream.
Commit 0a42e99b58a20883 ("loop: Get rid of loop_index_mutex") forgot to
remove mutex_unlock(&loop_ctl_mutex) from loop_control_ioctl() when
replacing loop_index_mutex with loop_ctl_mutex.
Fixes: 0a42e99b58a20883 ("loop: Get rid of loop_index_mutex")
Reported-by: syzbot <syzbot+c0138741c2290fc5e63f@syzkaller.appspotmail.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a42e99b58a208839626465af194cfe640ef9493 upstream.
Now that loop_ctl_mutex is global, just get rid of loop_index_mutex as
there is no good reason to keep these two separate and it just
complicates the locking.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 967d1dc144b50ad005e5eecdfadfbcfb399ffff6 upstream.
__loop_release() has a single call site. Fold it there. This is
currently not a huge win but it will make following replacement of
loop_index_mutex more obvious.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 310ca162d779efee8a2dc3731439680f3e9c1e86 upstream.
syzbot is reporting NULL pointer dereference [1] which is caused by
race condition between ioctl(loop_fd, LOOP_CLR_FD, 0) versus
ioctl(other_loop_fd, LOOP_SET_FD, loop_fd) due to traversing other
loop devices at loop_validate_file() without holding corresponding
lo->lo_ctl_mutex locks.
Since ioctl() request on loop devices is not frequent operation, we don't
need fine grained locking. Let's use global lock in order to allow safe
traversal at loop_validate_file().
Note that syzbot is also reporting circular locking dependency between
bdev->bd_mutex and lo->lo_ctl_mutex [2] which is caused by calling
blkdev_reread_part() with lock held. This patch does not address it.
[1] https://syzkaller.appspot.com/bug?id=f3cfe26e785d85f9ee259f385515291d21bd80a3
[2] https://syzkaller.appspot.com/bug?id=bf154052f0eea4bc7712499e4569505907d15889
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-by: syzbot <syzbot+bf89c128e05dd6c62523@syzkaller.appspotmail.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2753ca5d9009c180dbfd4c802c80983b4b6108d1 upstream.
BUG: KMSAN: uninit-value in tipc_nl_compat_doit+0x404/0xa10 net/tipc/netlink_compat.c:335
CPU: 0 PID: 4514 Comm: syz-executor485 Not tainted 4.16.0+ #87
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:17 [inline]
dump_stack+0x185/0x1d0 lib/dump_stack.c:53
kmsan_report+0x142/0x240 mm/kmsan/kmsan.c:1067
__msan_warning_32+0x6c/0xb0 mm/kmsan/kmsan_instr.c:683
tipc_nl_compat_doit+0x404/0xa10 net/tipc/netlink_compat.c:335
tipc_nl_compat_recv+0x164b/0x2700 net/tipc/netlink_compat.c:1153
genl_family_rcv_msg net/netlink/genetlink.c:599 [inline]
genl_rcv_msg+0x1686/0x1810 net/netlink/genetlink.c:624
netlink_rcv_skb+0x378/0x600 net/netlink/af_netlink.c:2447
genl_rcv+0x63/0x80 net/netlink/genetlink.c:635
netlink_unicast_kernel net/netlink/af_netlink.c:1311 [inline]
netlink_unicast+0x166b/0x1740 net/netlink/af_netlink.c:1337
netlink_sendmsg+0x1048/0x1310 net/netlink/af_netlink.c:1900
sock_sendmsg_nosec net/socket.c:630 [inline]
sock_sendmsg net/socket.c:640 [inline]
___sys_sendmsg+0xec0/0x1310 net/socket.c:2046
__sys_sendmsg net/socket.c:2080 [inline]
SYSC_sendmsg+0x2a3/0x3d0 net/socket.c:2091
SyS_sendmsg+0x54/0x80 net/socket.c:2087
do_syscall_64+0x309/0x430 arch/x86/entry/common.c:287
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
RIP: 0033:0x43fda9
RSP: 002b:00007ffd0c184ba8 EFLAGS: 00000213 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00000000004002c8 RCX: 000000000043fda9
RDX: 0000000000000000 RSI: 0000000020023000 RDI: 0000000000000003
RBP: 00000000006ca018 R08: 00000000004002c8 R09: 00000000004002c8
R10: 00000000004002c8 R11: 0000000000000213 R12: 00000000004016d0
R13: 0000000000401760 R14: 0000000000000000 R15: 0000000000000000
Uninit was created at:
kmsan_save_stack_with_flags mm/kmsan/kmsan.c:278 [inline]
kmsan_internal_poison_shadow+0xb8/0x1b0 mm/kmsan/kmsan.c:188
kmsan_kmalloc+0x94/0x100 mm/kmsan/kmsan.c:314
kmsan_slab_alloc+0x11/0x20 mm/kmsan/kmsan.c:321
slab_post_alloc_hook mm/slab.h:445 [inline]
slab_alloc_node mm/slub.c:2737 [inline]
__kmalloc_node_track_caller+0xaed/0x11c0 mm/slub.c:4369
__kmalloc_reserve net/core/skbuff.c:138 [inline]
__alloc_skb+0x2cf/0x9f0 net/core/skbuff.c:206
alloc_skb include/linux/skbuff.h:984 [inline]
netlink_alloc_large_skb net/netlink/af_netlink.c:1183 [inline]
netlink_sendmsg+0x9a6/0x1310 net/netlink/af_netlink.c:1875
sock_sendmsg_nosec net/socket.c:630 [inline]
sock_sendmsg net/socket.c:640 [inline]
___sys_sendmsg+0xec0/0x1310 net/socket.c:2046
__sys_sendmsg net/socket.c:2080 [inline]
SYSC_sendmsg+0x2a3/0x3d0 net/socket.c:2091
SyS_sendmsg+0x54/0x80 net/socket.c:2087
do_syscall_64+0x309/0x430 arch/x86/entry/common.c:287
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
In tipc_nl_compat_recv(), when the len variable returned by
nlmsg_attrlen() is 0, the message is still treated as a valid one,
which is obviously unresonable. When len is zero, it means the
message not only doesn't contain any valid TLV payload, but also
TLV header is not included. Under this stituation, tlv_type field
in TLV header is still accessed in tipc_nl_compat_dumpit() or
tipc_nl_compat_doit(), but the field space is obviously illegal.
Of course, it is not initialized.
Reported-by: syzbot+bca0dc46634781f08b38@syzkaller.appspotmail.com
Reported-by: syzbot+6bdb590321a7ae40c1a6@syzkaller.appspotmail.com
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 400b8b9a2a17918f8ce00786f596f530e7f30d50 upstream.
The similar issue as fixed in Commit 4a2eb0c37b47 ("sctp: initialize
sin6_flowinfo for ipv6 addrs in sctp_inet6addr_event") also exists
in sctp_inetaddr_event, as Alexander noticed.
To fix it, allocate sctp_sockaddr_entry with kzalloc for both sctp
ipv4 and ipv6 addresses, as does in sctp_v4/6_copy_addrlist().
Reported-by: Alexander Potapenko <glider@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reported-by: syzbot+ae0c70c0c2d40c51bb92@syzkaller.appspotmail.com
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b0e7310a2a33c06edc7eb81ffc521af9b2c5610 upstream.
levdatum->level can be NULL if we encounter an error while loading
the policy during sens_read prior to initializing it. Make sure
sens_destroy handles that case correctly.
Reported-by: syzbot+6664500f0f18f07a5c0e@syzkaller.appspotmail.com
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81c88b18de1f11f70c97f28ced8d642c00bb3955 upstream.
If we ignore the error we'll hit a null dereference a little later.
Reported-by: syzbot+4b98281f2401ab849f4b@syzkaller.appspotmail.com
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd26d1c4d1bc947b56ae404998ae2276df7b39b7 upstream.
If a filehandle is dup()ped, then it is possible to close it from one fd
and call mmap from the other. This creates a race condition in vb2_mmap
where it is using queue data that __vb2_queue_free (called from close())
is in the process of releasing.
By moving up the mutex_lock(mmap_lock) in vb2_mmap this race is avoided
since __vb2_queue_free is called with the same mutex locked. So vb2_mmap
now reads consistent buffer data.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reported-by: syzbot+be93025dd45dccd8923c@syzkaller.appspotmail.com
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5795fd38ee8194451ba3f281f075301a3696ce2 upstream.
From: Casey Schaufler <casey@schaufler-ca.com>
Check that the cred security blob has been set before trying
to clean it up. There is a case during credential initialization
that could result in this.
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Acked-by: John Johansen <john.johansen@canonical.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
Reported-by: syzbot+69ca07954461f189e808@syzkaller.appspotmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9729d6d282a6d7ce88e64c9119cecdf79edf4e88 upstream.
The capture DV timings capabilities allowed for a minimum width and
height of 0. So passing a timings struct with 0 values is allowed
and will later cause a division by zero.
Ensure that the width and height must be >= 16 to avoid this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: syzbot+57c3d83d71187054d56f@syzkaller.appspotmail.com
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 701f49bc028edb19ffccd101997dd84f0d71e279 upstream.
kthread_run returns an error pointer, but elsewhere in the code
dev->kthread_vid_cap/out is checked against NULL.
If kthread_run returns an error, then set the pointer to NULL.
I chose this method over changing all kthread_vid_cap/out tests
elsewhere since this is more robust.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: syzbot+53d5b2df0d9744411e2e@syzkaller.appspotmail.com
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a01421e4484327fe44f8e126793ed5a48a221e24 upstream.
Using [1] for static analysis I found that the OMAPFB_QUERY_PLANE,
OMAPFB_GET_COLOR_KEY, OMAPFB_GET_DISPLAY_INFO, and OMAPFB_GET_VRAM_INFO
cases could all leak uninitialized stack memory--either due to
uninitialized padding or 'reserved' fields.
Fix them by clearing the shared union used to store copied out data.
[1] https://github.com/vlad902/kernel-uninitialized-memory-checker
Signed-off-by: Vlad Tsyrklevich <vlad@tsyrklevich.net>
Reviewed-by: Kees Cook <keescook@chromium.org>
Fixes: b39a982dde ("OMAP: DSS2: omapfb driver")
Cc: security@kernel.org
[b.zolnierkie: prefix patch subject with "omap2fb: "]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a214720cbf50cd8c3f76bbb9c3f5c283910e9d33 upstream.
Octeon has an boot-time option to disable pcie.
Since MSI depends on PCI-E, we should also disable MSI also with
this option is on in order to avoid inadvertently accessing PCIe
registers.
Signed-off-by: YunQiang Su <ysu@wavecomp.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: pburton@wavecomp.com
Cc: linux-mips@vger.kernel.org
Cc: aaro.koskinen@iki.fi
Cc: stable@vger.kernel.org # v3.3+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac4ca4b9f4623ba5e1ea7a582f286567c611e027 upstream.
The tps6586x driver creates an irqchip that is used by its various child
devices for managing interrupts. The tps6586x-rtc device is one of its
children that uses the tps6586x irqchip. When using the tps6586x-rtc as
a wake-up device from suspend, the following is seen:
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.001 seconds) done.
OOM killer disabled.
Freezing remaining freezable tasks ... (elapsed 0.000 seconds) done.
Disabling non-boot CPUs ...
Entering suspend state LP1
Enabling non-boot CPUs ...
CPU1 is up
tps6586x 3-0034: failed to read interrupt status
tps6586x 3-0034: failed to read interrupt status
The reason why the tps6586x interrupt status cannot be read is because
the tps6586x interrupt is not masked during suspend and when the
tps6586x-rtc interrupt occurs, to wake-up the device, the interrupt is
seen before the i2c controller has been resumed in order to read the
tps6586x interrupt status.
The tps6586x-rtc driver sets it's interrupt as a wake-up source during
suspend, which gets propagated to the parent tps6586x interrupt.
However, the tps6586x-rtc driver cannot disable it's interrupt during
suspend otherwise we would never be woken up and so the tps6586x must
disable it's interrupt instead.
Prevent the tps6586x interrupt handler from executing on exiting suspend
before the i2c controller has been resumed by disabling the tps6586x
interrupt on entering suspend and re-enabling it on resuming from
suspend.
Cc: stable@vger.kernel.org
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a9372f751b5350e0ce3d2ee91832f1feae2c2e5 upstream.
While reading through the sysvipc implementation, I noticed that the n32
semctl/shmctl/msgctl system calls behave differently based on whether
o32 support is enabled or not: Without o32, the IPC_64 flag passed by
user space is rejected but calls without that flag get IPC_64 behavior.
As far as I can tell, this was inadvertently changed by a cleanup patch
but never noticed by anyone, possibly nobody has tried using sysvipc
on n32 after linux-3.19.
Change it back to the old behavior now.
Fixes: 78aaf956ba ("MIPS: Compat: Fix build error if CONFIG_MIPS32_COMPAT but no compat ABI.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: stable@vger.kernel.org # 3.19+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 44759979a49bfd2d20d789add7fa81a21eb1a4ab upstream.
Changing of caching mode via /sys/devices/.../scsi_disk/.../cache_type may
fail if device responds to MODE SENSE command with DPOFUA flag set, and
then checks this flag to be not set on MODE SELECT command.
In this scenario, when trying to change cache_type, write always fails:
# echo "none" >cache_type
bash: echo: write error: Invalid argument
And following appears in dmesg:
[13007.865745] sd 1:0:1:0: [sda] Sense Key : Illegal Request [current]
[13007.865753] sd 1:0:1:0: [sda] Add. Sense: Invalid field in parameter list
From SBC-4 r15, 6.5.1 "Mode pages overview", description of DEVICE-SPECIFIC
PARAMETER field in the mode parameter header:
...
The write protect (WP) bit for mode data sent with a MODE SELECT
command shall be ignored by the device server.
...
The DPOFUA bit is reserved for mode data sent with a MODE SELECT
command.
...
The remaining bits in the DEVICE-SPECIFIC PARAMETER byte are also reserved
and shall be set to zero.
[mkp: shuffled commentary to commit description]
Cc: stable@vger.kernel.org
Signed-off-by: Ivan Mironov <mironov.ivan@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9474f4e7cd71a633fa1ef93b7daefd44bbdfd482 upstream.
It's possible that a pid has died before we take the rcu lock, in which
case we can't walk the ancestry list as it may be detached. Instead, check
for death first before doing the walk.
Reported-by: syzbot+a9ac39bf55329e206219@syzkaller.appspotmail.com
Fixes: 2d514487fa ("security: Yama LSM")
Cc: stable@vger.kernel.org
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: James Morris <james.morris@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f9c469348487844328e162db57112f7d347c49f upstream.
Keys for "authenc" AEADs are formatted as an rtattr containing a 4-byte
'enckeylen', followed by an authentication key and an encryption key.
crypto_authenc_extractkeys() parses the key to find the inner keys.
However, it fails to consider the case where the rtattr's payload is
longer than 4 bytes but not 4-byte aligned, and where the key ends
before the next 4-byte aligned boundary. In this case, 'keylen -=
RTA_ALIGN(rta->rta_len);' underflows to a value near UINT_MAX. This
causes a buffer overread and crash during crypto_ahash_setkey().
Fix it by restricting the rtattr payload to the expected size.
Reproducer using AF_ALG:
#include <linux/if_alg.h>
#include <linux/rtnetlink.h>
#include <sys/socket.h>
int main()
{
int fd;
struct sockaddr_alg addr = {
.salg_type = "aead",
.salg_name = "authenc(hmac(sha256),cbc(aes))",
};
struct {
struct rtattr attr;
__be32 enckeylen;
char keys[1];
} __attribute__((packed)) key = {
.attr.rta_len = sizeof(key),
.attr.rta_type = 1 /* CRYPTO_AUTHENC_KEYA_PARAM */,
};
fd = socket(AF_ALG, SOCK_SEQPACKET, 0);
bind(fd, (void *)&addr, sizeof(addr));
setsockopt(fd, SOL_ALG, ALG_SET_KEY, &key, sizeof(key));
}
It caused:
BUG: unable to handle kernel paging request at ffff88007ffdc000
PGD 2e01067 P4D 2e01067 PUD 2e04067 PMD 2e05067 PTE 0
Oops: 0000 [#1] SMP
CPU: 0 PID: 883 Comm: authenc Not tainted 4.20.0-rc1-00108-g00c9fe37a7f27 #13
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-20181126_142135-anatol 04/01/2014
RIP: 0010:sha256_ni_transform+0xb3/0x330 arch/x86/crypto/sha256_ni_asm.S:155
[...]
Call Trace:
sha256_ni_finup+0x10/0x20 arch/x86/crypto/sha256_ssse3_glue.c:321
crypto_shash_finup+0x1a/0x30 crypto/shash.c:178
shash_digest_unaligned+0x45/0x60 crypto/shash.c:186
crypto_shash_digest+0x24/0x40 crypto/shash.c:202
hmac_setkey+0x135/0x1e0 crypto/hmac.c:66
crypto_shash_setkey+0x2b/0xb0 crypto/shash.c:66
shash_async_setkey+0x10/0x20 crypto/shash.c:223
crypto_ahash_setkey+0x2d/0xa0 crypto/ahash.c:202
crypto_authenc_setkey+0x68/0x100 crypto/authenc.c:96
crypto_aead_setkey+0x2a/0xc0 crypto/aead.c:62
aead_setkey+0xc/0x10 crypto/algif_aead.c:526
alg_setkey crypto/af_alg.c:223 [inline]
alg_setsockopt+0xfe/0x130 crypto/af_alg.c:256
__sys_setsockopt+0x6d/0xd0 net/socket.c:1902
__do_sys_setsockopt net/socket.c:1913 [inline]
__se_sys_setsockopt net/socket.c:1910 [inline]
__x64_sys_setsockopt+0x1f/0x30 net/socket.c:1910
do_syscall_64+0x4a/0x180 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Fixes: e236d4a89a ("[CRYPTO] authenc: Move enckeylen into key itself")
Cc: <stable@vger.kernel.org> # v2.6.25+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4a06fa67c4da20148803525151845276cdb995c1 ]
Commit 2efd4fca703a ("ip: in cmsg IP(V6)_ORIGDSTADDR call
pskb_may_pull") avoided a read beyond the end of the skb linear
segment by calling pskb_may_pull.
That function can trigger a BUG_ON in pskb_expand_head if the skb is
shared, which it is when when peeking. It can also return ENOMEM.
Avoid both by switching to safer skb_header_pointer.
Fixes: 2efd4fca703a ("ip: in cmsg IP(V6)_ORIGDSTADDR call pskb_may_pull")
Reported-by: syzbot <syzkaller@googlegroups.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d972f3dce8d161e2142da0ab1ef25df00e2f21a9 ]
'dev' is non NULL when the addr_len check triggers so it must goto a label
that does the dev_put otherwise dev will have a leaked refcount.
This bug causes the ib_ipoib module to become unloadable when using
systemd-network as it triggers this check on InfiniBand links.
Fixes: 99137b7888f4 ("packet: validate address length")
Reported-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4c84edc11b76590859b1e45dd676074c59602dc4 ]
When handling DNAT'ed packets on a bridge device, the neighbour cache entry
from lookup was used without checking its state. It means that a cache entry
in the NUD_STALE state will be used directly instead of entering the NUD_DELAY
state to confirm the reachability of the neighbor.
This problem becomes worse after commit 2724680bce ("neigh: Keep neighbour
cache entries if number of them is small enough."), since all neighbour cache
entries in the NUD_STALE state will be kept in the neighbour table as long as
the number of cache entries does not exceed the value specified in gc_thresh1.
This commit validates the state of a neighbour cache entry before using
the entry.
Signed-off-by: JianJhen Chen <kchen@synology.com>
Reviewed-by: JinLin Chen <jlchen@synology.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Backport of upstream commit b3669b1e1c09890d61109a1a8ece2c5b66804714 ]
To allow EL0 (and/or EL1) to use pointer authentication functionality,
we must ensure that pointer authentication instructions and accesses to
pointer authentication keys are not trapped to EL2.
This patch ensures that HCR_EL2 is configured appropriately when the
kernel is booted at EL2. For non-VHE kernels we set HCR_EL2.{API,APK},
ensuring that EL1 can access keys and permit EL0 use of instructions.
For VHE kernels host EL0 (TGE && E2H) is unaffected by these settings,
and it doesn't matter how we configure HCR_EL2.{API,APK}, so we don't
bother setting them.
This does not enable support for KVM guests, since KVM manages HCR_EL2
itself when running VMs.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: kvmarm@lists.cs.columbia.edu
Signed-off-by: Will Deacon <will.deacon@arm.com>
[kristina: backport to 4.4.y: adjust context]
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Backport of upstream commit 4eaed6aa2c628101246bcabc91b203bfac1193f8 ]
In KVM we define the configuration of HCR_EL2 for a VHE HOST in
HCR_HOST_VHE_FLAGS, but we don't have a similar definition for the
non-VHE host flags, and open-code HCR_RW. Further, in head.S we
open-code the flags for VHE and non-VHE configurations.
In future, we're going to want to configure more flags for the host, so
lets add a HCR_HOST_NVHE_FLAGS defintion, and consistently use both
HCR_HOST_VHE_FLAGS and HCR_HOST_NVHE_FLAGS in the kvm code and head.S.
We now use mov_q to generate the HCR_EL2 value, as we use when
configuring other registers in head.S.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: kvmarm@lists.cs.columbia.edu
Signed-off-by: Will Deacon <will.deacon@arm.com>
[kristina: backport to 4.4.y: non-VHE only; __deactivate_traps_nvhe in
assembly; add #include]
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Prevent an empty line in /proc/self/status, allow iotop to work.
iotop does not like empty lines, fails with:
File "/usr/local/lib64/python2.7/site-packages/iotop/data.py", line
196, in parse_proc_pid_status
key, value = line.split(':\t', 1)
ValueError: need more than 1 value to unpack
[reading /proc/self/status]
Fixes: 84964fa3e5a0 ("proc: Provide details on speculation flaw mitigations")
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The backport of commit afeaade90db4 "media: em28xx: make
v4l2-compliance happier by starting sequence on zero" added a
reset on em28xx_v4l2::field_count to em28xx_ctrl_notify(),
but it should be done in em28xx_start_analog_streaming().
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 88960068f25fcc3759455d85460234dcc9d43fef upstream.
Treat "block_count" from struct f2fs_super_block as 64-bit little endian
value in sanity_check_raw_super() because struct f2fs_super_block
declares "block_count" as "__le64".
This fixes a bug where the superblock validation fails on big endian
devices with the following error:
F2FS-fs (sda1): Wrong segment_count / block_count (61439 > 0)
F2FS-fs (sda1): Can't find valid F2FS filesystem in 1th superblock
F2FS-fs (sda1): Wrong segment_count / block_count (61439 > 0)
F2FS-fs (sda1): Can't find valid F2FS filesystem in 2th superblock
As result of this the partition cannot be mounted.
With this patch applied the superblock validation works fine and the
partition can be mounted again:
F2FS-fs (sda1): Mounted with checkpoint version = 7c84
My little endian x86-64 hardware was able to mount the partition without
this fix.
To confirm that mounting f2fs filesystems works on big endian machines
again I tested this on a 32-bit MIPS big endian (lantiq) device.
Fixes: 0cfe75c5b01199 ("f2fs: enhance sanity_check_raw_super() to avoid potential overflows")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89d13c38501df730cbb2e02c4499da1b5187119d upstream.
This patch fixes missing up_read call.
Fixes: c9b60788fc76 ("f2fs: fix to do sanity check with block address in main area")
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniel Santos
Anders Roxell
Maciej W. Rozycki
Miroslav Lichvar
João Paulo Rechi Vita
Darrick J. Wong
David Ahern
Kai-Heng Feng
Mauro Carvalho Chehab
Ivan Mironov
Tetsuo Handa
Jan Kara
Ying Xue
Xin Long
Stephen Smalley
J. Bruce Fields
Hans Verkuil
James Morris
Hans Verkuil
Vlad Tsyrklevich
YunQiang Su
Jonathan Hunter
Arnd Bergmann
Kees Cook
Josef Bacik
Eric Biggers
Harsh Jain
Willem de Bruijn
Jason Gunthorpe
JianJhen Chen
Eric Dumazet
Mark Rutland
Gwendal Grignou
Ben Hutchings
Martin Blumenstingl
Jaegeuk Kim
Chao Yu