There was some racing condition where the dsi status check
thread is called when the display is off. This makes sure
the dsi status check is not invoked when display is off.
Change-Id: I6865abe23ca7adf918a19499d3839d6664fc29fc
Signed-off-by: Xiaoming Zhou <zhoux@codeaurora.org>
Add support for rotator downscale, available from 8994. This allows
source data to be downscaled via power of 2 steps, before being
written back to memory.
Change-Id: If42a5a8c9cb336abfc22dc9848c24ec0f54cd878
Signed-off-by: Casey Piper <cpiper@codeaurora.org>
Signed-off-by: Saurabh Shah <saurshah@codeaurora.org>
Signed-off-by: Adrian Salido-Moreno <adrianm@codeaurora.org>
When continuous splash screen feature is enabled, the DSI phy and
controller are configured in the bootloader and left on. In such
cases, we do not need to initialize DSI phy and controller during
probe as it may overwrite the settings and can potentially cause
unexpected behaviors.
Change-Id: Ifdf4579be2a3cd45f71170237e0be193d78dba0f
Signed-off-by: Aravind Venkateswaran <aravindh@codeaurora.org>
control setup gets called for every suspend/resume and this warning
message is printed everytime. Hence, print panel's vfp related warning
message only once.
Change-Id: I4deb0d5faafca1f34a35fc37686bb55d8cbe02e5
Signed-off-by: Jeevan Shriram <jshriram@codeaurora.org>
The has_buf was introduced for a special case where buffers may not
be queued to MDP directly. Remove the has_buf variable since it is
not used anymore.
Change-Id: Ie8137991dc771b8b17da1f35d4bbbeb62ae8658b
Signed-off-by: Saurabh Shah <saurshah@codeaurora.org>
There are corner cases when pipes are still staged after
recovery sequence is over in overlay cleanup. Due to this
when destroying pipe, if pipe fetch halt tries to halt
the pipe, kernel bug happens and system gets crashed.
Hence, ensure pipes are unstaged before destroy.
Change-Id: If13ca0fce35656ecbc8f3c98e3017ac981dede06
Signed-off-by: Jayant Shekhar <jshekhar@codeaurora.org>
MDP3 hardware on ferrum has the capability to send panic/robust
signal to bimc based on fill level for DMA_P. This allows bimc
to prioritize the MDP traffic.
Change-Id: I41be85bda5c08cce6495e32fb76f804c816930ef
Signed-off-by: Shivaraj Shetty <shivaraj@codeaurora.org>
Add proper bail out and also avoid any commands involving
ACK from the panel.
Change-Id: Id321e1564f32a8b1565d2e735e8af54fb502751e
Signed-off-by: Anusha Koduru <kanusha@codeaurora.org>
In secure case, when same buffer is queued in multiple
composition cycles we should map it before unmapping it
so that TZ will not clear the buffer content.
In the former case ref count can be zero which can lead to TZ
clearing the buffer
Change-Id: I5aea01f8d2c4330b93319434ced55f816558619d
Signed-off-by: Kalyan Thota <kalyant@codeaurora.org>
Don't allow any ioctls like DISPLAY_COMMIT, OVERLAY_SET,
OVERLAY_PLAY when dsi dynamic switch is underway, to avoid
any stability issues.
Change-Id: I66e68e399c1fb31e7b9dcd3a4840d4fe59a58914
Signed-off-by: Sandeep Panda <spanda@codeaurora.org>
Partial update when enabled blocks all PP ioctls. There is
currently no subtle way to enable PP. Providing an ioctl
to override the blockage of PP ioctls. This would allow
PP to override the blockage caused due to the default
enablement of partial update.
Change-Id: Ia120caa179bfa0414041bacd80328540f24dd6c8
Signed-off-by: Krishna Chaitanya Parimi <cparimi@codeaurora.org>
DSI panel dynamic refresh rate range varies from panel to panel.
Add support to parse dynamic refresh range from the panel device
tree. If the range is not specified, use the default range from
30 to max panel supported rate.
Change-Id: Iac5adebe187bdc7abd4e82464de81305862df794
Signed-off-by: Jeevan Shriram <jshriram@codeaurora.org>
enable WB as secondary display when HDMI is configured as
primary panel.
Change-Id: Iffb635bdf4574d66e42c4320b122fde52ad1bf16
Signed-off-by: Ajay Singh Parmar <aparmar@codeaurora.org>
When updating userspace with the shared memory length,
the size of each buffer needs to be 4k aligned for
performance. This is also required to avoid mmap failures
in the case of recovery and other usecases where the
requested size is 4k aligned.
Change-Id: I6e97f9c76ea1aff07572c500f30f888b6e12f9b4
Signed-off-by: Jeevan Shriram <jshriram@codeaurora.org>
In case of HDMI is primary, get the default VIC (Video Identification
Code) from the command line to configure the display pipeline with this
resolution data for continuous splash screen.
Change-Id: I96325045f4af0712d2f68fadf190edcf6d815841
Signed-off-by: Ajay Singh Parmar <aparmar@codeaurora.org>
On 8916/8939, the DSI timing registers support double buffering.
Enable the double buffering support and flush DSI registers once
the timing parameters are configured.
Change-Id: I61c0a84f0fc015541fc8e0197e1b9997ebb123aa
Signed-off-by: Padmanabhan Komanduru <pkomandu@codeaurora.org>
Currently MDP driver rejects reusing of a pipe if this reuse results
in wastage of SMPs. i.e. VIG0 pipe reused from YUV layer to RGB layer.
In this case, since RGB layer needs only plane0, plane1 SMPs are unused.
This kind of wasting leads to un-necessary GPU fall-backs for composition
when number of SMPs and number of pipes are less. For this reason driver
used to prohibit such configuration. But in high tier chip-sets, there
are enough number of SMPs and pipes are available such that these
transient wastage of SMPs can be absorbed without much impact.
Change-Id: Ia7baec801add81e5c97bded920ae5bdca5083e0b
Signed-off-by: Ujwal Patel <ujwalp@codeaurora.org>
Moving away from using sg_dma_len() api to be inline with
ion driver, use sg->length for scatterlist length.
Change-Id: I3a33340dc1bda5b24a406c29601aff4d5b2c5748
Signed-off-by: Jeevan Shriram <jshriram@codeaurora.org>
Add edid_audio_latency and edid_video_latency sysfs nodes to
report the info extracted from edid. AV sync can use these info
to compensate the difference.
Change-Id: I2b1a3f6c0e2d892be8d41651ea898ce47c9d820b
Signed-off-by: Ken Zhang <kenz@codeaurora.org>
While validating pixel extension calculations from user space,
validate the over fetch pixels with image dimentions in both
horizontal and vertical directions.
Change-Id: I8e39e89d9ace8e26237b3b23ca375456abd804a1
Signed-off-by: Jeevan Shriram <jshriram@codeaurora.org>
If a layer needs a scaling than its pixel extension values are calculated
in the user-space library and passed down to driver. Currently driver
blindly programs these settings to HW without validating for correctness.
This leads to HW hangs and stability issues. Add a proper sanitization
checks for pixel extension and report error back to user-space if any.
Change-Id: I086cf0b23fbccd37a23bb509f067bffdf396c247
Signed-off-by: Ujwal Patel <ujwalp@codeaurora.org>
Signed-off-by: Jeevan Shriram <jshriram@codeaurora.org>
When HDMI is turned off, sending CEC will crash the system
and the logical address will be lost. Do not send CEC message
if CEC is not configured. Initialize CEC logical address when
config CEC during turning on HDMI. Return an error when sending
message fails so that HAL can know the result.
Change-Id: I2f5ced4d9be97361665138400bde435916c7373e
Signed-off-by: Ken Zhang <kenz@codeaurora.org>
For smoother power off and resolution change, set av mute during
power off.
Change-Id: I96e2a9647f42c033acbab72e87593ef6fdedfbc0
Signed-off-by: Ajay Singh Parmar <aparmar@codeaurora.org>
Keep re-authenticating until successful as sinks may choose
not to issue HPD while switching HDMI ports or powering on/off
which usually trigger HDCP on/off.
Change-Id: Ib4b13592df8753df1693c6279f04fc963ba9974f
Signed-off-by: Ajay Singh Parmar <aparmar@codeaurora.org>
Some sinks may have more than one audio data block (adb).
Add support to parse more than one adb.
Change-Id: Icf324c2e8b6fbd3817bcdb54a62eb0af17996fa4
Signed-off-by: Ajay Singh Parmar <aparmar@codeaurora.org>
LP/HS mode configuration for DCS Commands in currently not
supported on MDP5 targets. Add the required support to meet
all panel requirements.
Change-Id: Ib31ddc02f151033a59d6297c8f1a4f8897378947
Signed-off-by: Shuo Yan <shuoy@codeaurora.org>
Add mdss version macro for 8992 target and initialize maximum
blending stages supported for the target.
Change-Id: Ic741fb725907498791c1d17581561e3632a40cec
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
There are two completion structures associated with the histogram. When
hist is being disabled, we complete_all() these structures to unblock the
waiting threads, however the completes were not done in the same order as
the waits.
Change-Id: I0dc39d56db9b4f141b619ae41f2c896d2e84c882
Signed-off-by: Benet Clark <benetc@codeaurora.org>
IOMMU page faults can happen if iommu is attached in pan display
if continuous splash is enabled as splash fetches from physical
memory. Splash cleanup is performed in overlay start and hence
move iommu attach after splash cleanup is done.
Change-Id: I703c925f964527f33108a3a09ee1ffdc0a3003cd
Signed-off-by: Jayant Shekhar <jshekhar@codeaurora.org>
Fix to consider all the vertical blanking lines for
the prefill bandwidth calculation and keep skipping
one pixel for the fetch start configuration.
Change-Id: I3407f8ef4c6427a307220bee10f9cac072582069
Signed-off-by: Ingrid Gallardo <ingridg@codeaurora.org>
If a transition from full suspend to doze mode is requested, first
unblank the panel and then enter the doze mode. This is necessary
to ensure that all necessary panel supplies are turned on and the
panel is brought out of reset first.
Change-Id: I5757f01ec9843a332fd2d1034c068ff993f466bd
Signed-off-by: Aravind Venkateswaran <aravindh@codeaurora.org>
When HDMI is primary, do not issue runtime suspend and resume events
to HDMI interface. Runtime suspend/resume may get triggered with cable
connect/disconnect when HDMI is primary which will result in unnecessary
power on/off of HPD module.
Change-Id: I6c0c9eb85832717be538b3fbf7583b1e4a5c10d5
Signed-off-by: Ajay Singh Parmar <aparmar@codeaurora.org>
A bounds check has to be done on ovlist32->num_overlays variable
so as to prevent memory allocation of arbitrary size and avoid
subsequent undetermined behaviour.
Change-Id: Ic70726f1825040e793ef256195d236d77b392791
Signed-off-by: Nirmal Abraham <nabrah@codeaurora.org>
Signed-off-by: Raghavendra Ambadas <rambad@codeaurora.org>
Signed-off-by: Krishna Chaitanya Parimi <cparimi@codeaurora.org>
The option for split mode in PP only checks the enable flag of the
feature in order to enable the same in the DSPP opmode. The opmode bits for
PAv2 features need to be disabled if PA bit is disabled.
Change-Id: I72019d0d03703e0698cf8d4ccd8b8f9c17889653
Signed-off-by: Benet Clark <benetc@codeaurora.org>
fget_light was deprecated, made the switch to fdget.
Change-Id: I52a032f26002300a1bf58573ff40fcc84c35d74e
Signed-off-by: Terence Hampson <thampson@codeaurora.org>
[cip@codeaurora.org: Replace f_dentry with f_path.dentry]
Signed-off-by: Clarence Ip <cip@codeaurora.org>
IOMMU APIs are changing in 3.14 kernel. ION IOMMU calls, such as
ion_unmap_iommu, are being deprecated. While transition to new
APIs calling msm_map_dma_buf is an intermediate stage when
transitioning to new APIs.
Change-Id: I7fb11575d3924073fa9917be32ac2f92634f2e13
Signed-off-by: Terence Hampson <thampson@codeaurora.org>
In order to prevent trace compilation warning, need to explicitly setup
compile include directive to search current source folder for header
files.
Change-Id: Ic17f841c88d911498d914f5339c99d2cb1ae3d1a
Signed-off-by: Adrian Salido-Moreno <adrianm@codeaurora.org>
[cip@codeaurora.org: Resolved merge conflict]
Signed-off-by: Clarence Ip <cip@codeaurora.org>
Changing all instances of sysfs_dirent -> kernfs_node.
Additionally parameters passed into sysfs_get_dirent changed
which is corrected in this patch.
Change-Id: I06ce0b6af0d88248fb8019a68fd637bd6ce5b12e
Signed-off-by: Terence Hampson <thampson@codeaurora.org>
Inline function usleep translating to usleep_range no longer
provided in 3.14 kernel. Moving all usleep in display code
to use usleep_range.
Change-Id: Ie2a465107f83beaedb82380ca8d57c1d9190ec7f
Signed-off-by: Terence Hampson <thampson@codeaurora.org>
In porting Id726a65b5641b57c0edd3ba33f2e5b3f68aff643
misspelt header file that was change. This patch corrects
that mistake.
Change-Id: I6755b102742e663f272b10f3b9804493e81ac28f
Signed-off-by: Terence Hampson <thampson@codeaurora.org>
Removing all calls to kgsl_drm, as it is no longer supported
in 3.14 kernel.
Change-Id: I835a946d6b032f47121e19b6ddb8629e672088ea
Signed-off-by: Terence Hampson <thampson@codeaurora.org>
INIT_COMPLETION is removed from 3.14 kernel. Replacing with
reinit_completion.
Change-Id: I64c43e313ff4e07dc7900bdce155f8c55e5ed420
Signed-off-by: Terence Hampson <thampson@codeaurora.org>
The DSI branch blocks needs to be on in order to issue a DSI software
reset. Commit e8c272ba5c3f23e6cece61bde7834cab7922a1d4 introduced the
change which moved the DSI software reset prior to enabling the DSI
branch clocks in order to support the idle power collapse feature.
This is not correct since a soft reset is not required at all when
resuming from an idle power collapsed state. Fix this by moving the
software reset to the DSI on sequence.
Change-Id: I663a44d04650f686ba98ea0b1fb7ab2ea29a3bcc
Signed-off-by: Aravind Venkateswaran <aravindh@codeaurora.org>
Whenever the display always-on feature is enabled, it is possible
that the display pipeline can be in an intermediate state between being
fully interactive to fully turned off. In the current implementation, a
number of state transition decisions are made based on whether the
display pipeline is on or not. Instead of explicitly checking for the
panel power state, define generic helper functions which classify the
panel power state into three different stages - interactive, low-power
and off. Replace any existing check for the panel power state with these
newly defined helper functions.
Change-Id: I4d6dd883ea6aca8abd57fa048a79e0c88da09a95
Signed-off-by: Aravind Venkateswaran <aravindh@codeaurora.org>
Add a new panel power state to represent a panel low power mode. Add a
new sysfs node to control when to configure the panel into this new
mode.
Change-Id: I7df8bf63470bec893c6b7481678f00ce76b6875c
Signed-off-by: Aravind Venkateswaran <aravindh@codeaurora.org>
Currently a panel either be in a powered on state or a powered off
state. However, it is possible for panels to be configured in an
intermediate low-power state where the panel is always kept on. In
order to support such use-cases, it is necessary to add the concept
of panel power states in MDSS so that each software layer can
independently maintain it's state and manage transitions between them.
This change just refactors the driver with only two existing power
states - panel on and panel off.
Change-Id: I49d1fda506761546c5e22d9106c5177e75053a81
Signed-off-by: Aravind Venkateswaran <aravindh@codeaurora.org>
After configuration is done, save the acquired fences,
release the kickoff and ov_lock, then wait for the cached
fences. This way the next prepare will not be blocked by
waiting for acquired fences.
Change-Id: Id6f5b30e0d20cd59bd0aebf71af7cb47ecb1cf5b
Signed-off-by: Ken Zhang <kenz@codeaurora.org>
MDP clock requirement for rotator depends solely on source dimensions,
rot_clk = (src_w * src_h * fps). Fix current calculations where MDP clock
rate is incorrectly calculated as rot_clk = (dst_h * dst_h *fps). New
calculations are valid even when down-scale is done along with rotation.
Change-Id: I30d98b7a62beeb3a559a9c5f26de43c014fd25fd
Signed-off-by: Ujwal Patel <ujwalp@codeaurora.org>
