Add device tree configuration corresponding to all
supported ion heaps for msmfalcon.
Change-Id: I639e8bfb1275a1b8c8fa5bff3a46f9b34fe49ffe
Signed-off-by: Shiraz Hashim <shashim@codeaurora.org>
Add carve-outs, firmware regions and other cma areas as
part of initial memory map configuration for msmfalcon.
Change-Id: I2b0d35bf90b92f7fbd4256f339c1567d539e17b2
Signed-off-by: Shiraz Hashim <shashim@codeaurora.org>
Add support for Analog MIC and Digital MIC recording
for wcd934x codec.
CRs-Fixed: 1041199
Change-Id: I79e07682661fea99baaa29f8807eaf2f684f65be
Signed-off-by: Yeleswarapu Nagaradhesh <nagaradh@codeaurora.org>
When predictive dcvs is enabled a tracepoint will log a value that is
garbage due to being uninitialized. Fix this.
CRs-fixed: 1042660
Change-Id: I2b94e78f2470dbc2fd469b5cab287d643e8f3227
Signed-off-by: Olav Haugan <ohaugan@codeaurora.org>
Turning on sched_use_pelt causes a null-pointer dereference in
scheduler. Add correct checking of varable.
CRs-fixed: 1042656
Change-Id: I6e6a57e24b41e4b3d049bfcf694b9ad7e2144dd5
Signed-off-by: Olav Haugan <ohaugan@codeaurora.org>
Tavil is sourced from lnbbclk2 and hence enable
this clock for tavil codec.
CRs-Fixed: 1041199
Change-Id: I5409b0f4ed58fefdd25abbe79f144de7e693c1a1
Signed-off-by: Yeleswarapu Nagaradhesh <nagaradh@codeaurora.org>
Add wcd934x as a mfd child and configure regmap.
Configure MCLK as per the HW sequence.
CRs-Fixed: 1041199
Change-Id: I9e2dbb0f0acaa1442c1624556bc52abf98158c92
Signed-off-by: Yeleswarapu Nagaradhesh <nagaradh@codeaurora.org>
SMD clients for DSPS have migrated to G-Link.
Remove SMD device for DSPS edge.
CRs-Fixed: 1041462
Change-Id: I9f62cc0e8229b86500fa72908be5c503847aed8f
Signed-off-by: Chris Lew <clew@codeaurora.org>
SMD clients for ADSP have migrated to G-Link.
Remove SMD device for ADSP edge.
CRs-Fixed: 1041461
Change-Id: I299d31569291e90431802059f727a57ea0f76200
Signed-off-by: Chris Lew <clew@codeaurora.org>
SMD clients for Modem have migrated to G-Link.
Remove SMD device for Modem edge.
CRs-Fixed: 1041459
Change-Id: I6122ceb014f70b8e0ac005bc3789fbd13a3e867a
Signed-off-by: Chris Lew <clew@codeaurora.org>
It has been observed that default values for some of key tcp/ip
parameters are affecting the tput/performance of the system. Hence
extending configuration capabilities to TCP/Ip stack through
sysctl interface
Change-Id: I4287e9103769535f43e0934bac08435a524ee6a4
CRs-Fixed: 507581
Signed-off-by: Ravi Joshi <ravij@codeaurora.org>
Signed-off-by: Ganesh Babu Kumaravel <kganesh@codeaurora.org>
Signed-off-by: Mohit Khanna <mkhannaqca@codeaurora.org>
The gcc_bimc_hmss_axi_clk will be configured outside of HLOS.
The linux clock driver does not need to manually enable it.
CRs-Fixed: 1012646
Change-Id: Ib0b848fb410f4bf266b09cefed0e8bce7292d2ec
Signed-off-by: Deepak Katragadda <dkatraga@codeaurora.org>
Update decimator high pass filter cutoff frequency if the
TX is path closed within 300ms after opening the session.
This will restore the cutoff frequency to the default
correct value.
CRs-fixed: 988075
Change-Id: Iece28fe2551a74ec7b1b8b4b5cac02537e3d28d8
Signed-off-by: Phani Kumar Uppalapati <phaniu@codeaurora.org>
If a USB charger is already attached before the master charger
probes, the master will miss updating parallel charging states.
ICL and charge state change interrupts get triggered before
their handlers are registered. Hence these interrupts will not
be handled. Obtain the state of missing interrupts by polling
status registers.
If parallel charging is ready on master side before the parallel
charger probes, then parallel charging will not be enabled.
Check if parallel charging is ready once the parallel charger
probes so parallel charging can be enabled immediately.
CRs-Fixed: 1033688
Change-Id: Ic91baeaeb7410b6f265b8bfa8e31e2bcff8dfce2
Signed-off-by: Harry Yang <harryy@codeaurora.org>
This change adds debug event to capture pull up operation request.
It also captures if software fails to perfrom pull-up operation
here.
CRs-Fixed: 1036037
Change-Id: I77ecff3a2ac395ff3799c1b0618fbc7f5eeb03da
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
When clients dumps PCIe PARF registers, it should not flood
dmesg. Change the logging type for dumping PCIe PARF register
to a lower priority one. The dump will only show up in PCIe
specific logs and not dmesg.
Change-Id: Ide04b0d2017ce3c1a99edd2b38ef5b06178a1f41
Signed-off-by: Tony Truong <truong@codeaurora.org>
The peripheral_mem carveout currently contains three separate images.
If these images are dynamically unloaded and reloaded in the wrong
order they could fragment the memory such that not all images would
fit.
Break apart the peripheral_mem into separate carveouts for each PIL
image to avoid the possibility of fragmentation.
CRs-Fixed: 1024397
Change-Id: Id9607b7e4a5e0cdcbf4c36ffad32536dd0669005
Signed-off-by: Liam Mark <lmark@codeaurora.org>
