commit 2e18f5a1bc18e8af7031b3b26efde25307014837 upstream.
Introduce a dt property, ti,no-idle, that prevents an IP to idle at any
point. This is to handle Errata i877, which tells that GMAC clocks
cannot be disabled.
Acked-by: Roger Quadros <rogerq@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f514e690740e54815441a87708c3326f8aa8709 upstream.
Errata id: i877
Description:
------------
The RGMII 1000 Mbps Transmit timing is based on the output clock
(rgmiin_txc) being driven relative to the rising edge of an internal
clock and the output control/data (rgmiin_txctl/txd) being driven relative
to the falling edge of an internal clock source. If the internal clock
source is allowed to be static low (i.e., disabled) for an extended period
of time then when the clock is actually enabled the timing delta between
the rising edge and falling edge can change over the lifetime of the
device. This can result in the device switching characteristics degrading
over time, and eventually failing to meet the Data Manual Delay Time/Skew
specs.
To maintain RGMII 1000 Mbps IO Timings, SW should minimize the
duration that the Ethernet internal clock source is disabled. Note that
the device reset state for the Ethernet clock is "disabled".
Other RGMII modes (10 Mbps, 100Mbps) are not affected
Workaround:
-----------
If the SoC Ethernet interface(s) are used in RGMII mode at 1000 Mbps,
SW should minimize the time the Ethernet internal clock source is disabled
to a maximum of 200 hours in a device life cycle. This is done by enabling
the clock as early as possible in IPL (QNX) or SPL/u-boot (Linux/Android)
by setting the register CM_GMAC_CLKSTCTRL[1:0]CLKTRCTRL = 0x2:SW_WKUP.
So, do not allow to gate the cpsw clocks using ti,no-idle property in
cpsw node assuming 1000 Mbps is being used all the time. If someone does
not need 1000 Mbps and wants to gate clocks to cpsw, this property needs
to be deleted in their respective board files.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d7d5a43c0d16760f25d892bf9329848167a8b8a4 upstream.
When the Crypto SRAM mappings were added to the Device Tree files
describing the Armada XP boards in commit c466d997bb ("ARM: mvebu:
define crypto SRAM ranges for all armada-xp boards"), the fact that
those mappings were overlaping with the PCIe memory aperture was
overlooked. Due to this, we currently have for all Armada XP platforms
a situation that looks like this:
Memory mapping on Armada XP boards with internal registers at
0xf1000000:
- 0x00000000 -> 0xf0000000 3.75G RAM
- 0xf0000000 -> 0xf1000000 16M NOR flashes (AXP GP / AXP DB)
- 0xf1000000 -> 0xf1100000 1M internal registers
- 0xf8000000 -> 0xffe0000 126M PCIe memory aperture
- 0xf8100000 -> 0xf8110000 64KB Crypto SRAM #0 => OVERLAPS WITH PCIE !
- 0xf8110000 -> 0xf8120000 64KB Crypto SRAM #1 => OVERLAPS WITH PCIE !
- 0xffe00000 -> 0xfff00000 1M PCIe I/O aperture
- 0xfff0000 -> 0xffffffff 1M BootROM
The overlap means that when PCIe devices are added, depending on their
memory window needs, they might or might not be mapped into the
physical address space. Indeed, they will not be mapped if the area
allocated in the PCIe memory aperture by the PCI core overlaps with
one of the Crypto SRAM. Typically, a Intel IGB PCIe NIC that needs 8MB
of PCIe memory will see its PCIe memory window allocated from
0xf80000000 for 8MB, which overlaps with the Crypto SRAM windows. Due
to this, the PCIe window is not created, and any attempt to access the
PCIe window makes the kernel explode:
[ 3.302213] igb: Copyright (c) 2007-2014 Intel Corporation.
[ 3.307841] pci 0000:00:09.0: enabling device (0140 -> 0143)
[ 3.313539] mvebu_mbus: cannot add window '4:f8', conflicts with another window
[ 3.320870] mvebu-pcie soc:pcie-controller: Could not create MBus window at [mem 0xf8000000-0xf87fffff]: -22
[ 3.330811] Unhandled fault: external abort on non-linefetch (0x1008) at 0xf08c0018
This problem does not occur on Armada 370 boards, because we use the
following memory mapping (for boards that have internal registers at
0xf1000000):
- 0x00000000 -> 0xf0000000 3.75G RAM
- 0xf0000000 -> 0xf1000000 16M NOR flashes (AXP GP / AXP DB)
- 0xf1000000 -> 0xf1100000 1M internal registers
- 0xf1100000 -> 0xf1110000 64KB Crypto SRAM #0 => OK !
- 0xf8000000 -> 0xffe0000 126M PCIe memory
- 0xffe00000 -> 0xfff00000 1M PCIe I/O
- 0xfff0000 -> 0xffffffff 1M BootROM
Obviously, the solution is to align the location of the Crypto SRAM
mappings of Armada XP to be similar with the ones on Armada 370, i.e
have them between the "internal registers" area and the beginning of
the PCIe aperture.
However, we have a special case with the OpenBlocks AX3-4 platform,
which has a 128 MB NOR flash. Currently, this NOR flash is mapped from
0xf0000000 to 0xf8000000. This is possible because on OpenBlocks
AX3-4, the internal registers are not at 0xf1000000. And this explains
why the Crypto SRAM mappings were not configured at the same place on
Armada XP.
Hence, the solution is two-fold:
(1) Move the NOR flash mapping on Armada XP OpenBlocks AX3-4 from
0xe8000000 to 0xf0000000. This frees the 0xf0000000 ->
0xf80000000 space.
(2) Move the Crypto SRAM mappings on Armada XP to be similar to
Armada 370 (except of course that Armada XP has two Crypto SRAM
and not one).
After this patch, the memory mapping on Armada XP boards with
registers at 0xf1 is:
- 0x00000000 -> 0xf0000000 3.75G RAM
- 0xf0000000 -> 0xf1000000 16M NOR flashes (AXP GP / AXP DB)
- 0xf1000000 -> 0xf1100000 1M internal registers
- 0xf1100000 -> 0xf1110000 64KB Crypto SRAM #0
- 0xf1110000 -> 0xf1120000 64KB Crypto SRAM #1
- 0xf8000000 -> 0xffe0000 126M PCIe memory
- 0xffe00000 -> 0xfff00000 1M PCIe I/O
- 0xfff0000 -> 0xffffffff 1M BootROM
And the memory mapping for the special case of the OpenBlocks AX3-4
(internal registers at 0xd0000000, NOR of 128 MB):
- 0x00000000 -> 0xc0000000 3G RAM
- 0xd0000000 -> 0xd1000000 1M internal registers
- 0xe800000 -> 0xf0000000 128M NOR flash
- 0xf1100000 -> 0xf1110000 64KB Crypto SRAM #0
- 0xf1110000 -> 0xf1120000 64KB Crypto SRAM #1
- 0xf8000000 -> 0xffe0000 126M PCIe memory
- 0xffe00000 -> 0xfff00000 1M PCIe I/O
- 0xfff0000 -> 0xffffffff 1M BootROM
Fixes: c466d997bb ("ARM: mvebu: define crypto SRAM ranges for all armada-xp boards")
Reported-by: Phil Sutter <phil@nwl.cc>
Cc: Phil Sutter <phil@nwl.cc>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 36e5cd6b897e17d03008f81e075625d8e43e52d0 upstream.
Commit dfd55ad85e4a ("arm64: vmemmap: use virtual projection of linear
region") fixed an issue where the struct page array would overflow into the
adjacent virtual memory region if system RAM was placed so high up in
physical memory that its addresses were not representable in the build time
configured virtual address size.
However, the fix failed to take into account that the vmemmap region needs
to be relatively aligned with respect to the sparsemem section size, so that
a sequence of page structs corresponding with a sparsemem section in the
linear region appears naturally aligned in the vmemmap region.
So round up vmemmap to sparsemem section size. Since this essentially moves
the projection of the linear region up in memory, also revert the reduction
of the size of the vmemmap region.
Fixes: dfd55ad85e4a ("arm64: vmemmap: use virtual projection of linear region")
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: David Daney <david.daney@cavium.com>
Tested-by: Robert Richter <rrichter@cavium.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When upstream commit 429c45deae6e57f1bb91bfb05b671063fb0cef60
was applied to 4.4 as d60703ca94
it applied incorrectly to the tonga_ip_blocks array rather than
the topaz_ip_blocks array. Fix that up here.
Bug:
https://bugzilla.kernel.org/show_bug.cgi?id=113951
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8244062ef1e54502ef55f54cced659913f244c3e upstream.
For CONFIG_KALLSYMS, we keep two symbol tables and two string tables.
There's one full copy, marked SHF_ALLOC and laid out at the end of the
module's init section. There's also a cut-down version that only
contains core symbols and strings, and lives in the module's core
section.
After module init (and before we free the module memory), we switch
the mod->symtab, mod->num_symtab and mod->strtab to point to the core
versions. We do this under the module_mutex.
However, kallsyms doesn't take the module_mutex: it uses
preempt_disable() and rcu tricks to walk through the modules, because
it's used in the oops path. It's also used in /proc/kallsyms.
There's nothing atomic about the change of these variables, so we can
get the old (larger!) num_symtab and the new symtab pointer; in fact
this is what I saw when trying to reproduce.
By grouping these variables together, we can use a
carefully-dereferenced pointer to ensure we always get one or the
other (the free of the module init section is already done in an RCU
callback, so that's safe). We allocate the init one at the end of the
module init section, and keep the core one inside the struct module
itself (it could also have been allocated at the end of the module
core, but that's probably overkill).
[ Rebased for 4.4-stable and older, because the following changes aren't
in the older trees:
- e0224418516b4d8a6c2160574bac18447c354ef0: adds arg to is_core_symbol
- 7523e4dc5057e157212b4741abd6256e03404cf1: module_init/module_core/init_size/core_size
become init_layout.base/core_layout.base/init_layout.size/core_layout.size.
]
Reported-by: Weilong Chen <chenweilong@huawei.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=111541
Cc: stable@kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f2e305108faba0c85eb4ba4066599decb675117e upstream.
The test for the qemu q35 south bridge added by commit
"39bfcd52 drm/i915: more virtual south bridge detection"
also matches on real hardware. Having the check for
virtual systems last in the list is not enough to avoid
that ...
Refine the check by additionally verifying the pci
subsystem id to see whenever it *really* is qemu.
[ v2: fix subvendor tyops ]
Reported-and-tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Bruno Wolff III <bruno@wolff.to>
Cc: drm-intel-fixes@lists.freedesktop.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453719748-10944-1-git-send-email-kraxel@redhat.com
(cherry picked from commit 1e859111c128265f8d62b39ff322e42b1ddb5a20)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 25e71a99f10e444cd00bb2ebccb11e1c9fb672b1 upstream.
This patch applies the two introduced helpers to
figure out the 1st and last bvec, and fixes the
original way after bio splitting.
Reported-by: Sagi Grimberg <sagig@dev.mellanox.co.il>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e0af29171aa8912e1ca95023b75ef336cd70d661 upstream.
In the following patch, the way for figuring out
the last bvec will be changed with a bit cost introduced,
so return immediately if the queue doesn't have virt
boundary limit. Actually most of devices have not
this limit.
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9571e1d84042f5670df9fabdcbe7dd5da3abe43e upstream.
It can be big, depending on the VM address space size, which is tunable
via the vm_size module parameter.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93721
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a53b8394ec3c67255928df6ee9cc99dd1cd452e3 upstream.
In __cpufreq_cooling_register() we allocate the arrays for time_in_idle
and time_in_idle_timestamp to be as big as the number of cpus in this
cpufreq device. However, in get_load() we access this array using the
cpu number as index, which can result in an out of bound access.
Index time_in_idle{,_timestamp} using the index in the cpufreq_device's
allowed_cpus mask, as we do for the load_cpu array in
cpufreq_get_requested_power()
Reported-by: Nicolas Boichat <drinkcat@chromium.org>
Cc: Amit Daniel Kachhap <amit.kachhap@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7314d22a2f5bd40468d57768be368c3d9b4bd726 upstream.
We want the size of the struct, not of a pointer to it. To be future
proof, just dereference the pointer to get the desired type.
Fixes: dd1aa2524b ("i2c: brcmstb: Add Broadcom settop SoC i2c controller driver")
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4f6daac20332448529b11f09388f1d55ef2084c upstream.
ubi_start_leb_change() allocates too few bytes.
ubi_more_leb_change_data() will write up to req->upd_bytes +
ubi->min_io_size bytes.
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 923adb1646d5ba739d2a1e63ee20d60574d9da8e upstream.
The PSL timebase synchronization is seemingly failing for
configuration not including VIRT_CPU_ACCOUNTING_NATIVE. The driver
shows the following trace in dmesg:
PSL: Timebase sync: giving up!
The PSL timebase register is actually syncing correctly, but the cxl
driver is not detecting it. Fix is to use the proper timebase-to-time
conversion.
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e723e3f7f9591b79e8c56b3d7c5a204a9c571b55 upstream.
Avoid sending a partially initialised `siginfo_t' structure along SIGFPE
signals issued from `do_ov' and `do_trap_or_bp', leading to information
leaking from the kernel stack.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56fa81fc9a5445938f3aa2e63d15ab63dc938ad6 upstream.
In current scache init cache line_size is determined from
cpu config register, however if there there no scache
then mips_sc_probe_cm3 function populates a invalid line_size of 2.
The invalid line_size can cause a NULL pointer deference
during r4k_dma_cache_inv as r4k_blast_scache is populated
based on line_size. Scache line_size of 2 is invalid option in
r4k_blast_scache_setup.
This issue was faced during a MIPS I6400 based virtual platform bring up
where scache was not available in virtual platform model.
Signed-off-by: Govindraj Raja <Govindraj.Raja@imgtec.com>
Fixes: 7d53e9c4cd21("MIPS: CM3: Add support for CM3 L2 cache.")
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hartley <James.Hartley@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12710/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5deef5551c77e488922cc4bf4bc76df63be650d0 upstream.
This patch adds support for 0x1045 PID of Telit LE922.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04fdbc825ffc02fb098964b92de802fff44e73fd upstream.
The MC74xx and EM74xx modules use different IDs by default, according
to the Lenovo EM7455 driver for Windows.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c4c615d70c8cbdc8ba8c79ed702640930652a79 upstream.
The Parrot NMEA GPS Flight Recorder is a USB composite device
consisting of hub, flash storage, and cp210x usb to serial chip.
It is an accessory to the mass-produced Parrot AR Drone 2.
The device emits standard NMEA messages which make the it compatible
with NMEA compatible software. It was tested using gpsd version 3.11-3
as an NMEA interpreter and using the official Parrot Flight Recorder.
Signed-off-by: Vittorio Alfieri <vittorio88@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a72494ac2a3bd229db941d51e7efe2f6ccd947b upstream.
The timer user status compat ioctl returned the bogus struct used for
64bit architectures instead of the 32bit one. This patch addresses
it to return the proper struct.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1099c3294c2344110085a38c50e478a5992b368 upstream.
HDSPM driver contains a code issuing zero-division potentially in
system sample rate ctl code. This patch fixes it by not processing
a zero or invalid rate value as a divisor, as well as excluding the
invalid value to be passed via the given ctl element.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 197b958c1e76a575d77038cc98b4bebc2134279f upstream.
The OSS sequencer client tries to drain the pending events at
releasing. Unfortunately, as spotted by syzkaller fuzzer, this may
lead to an unkillable process state when the event has been queued at
the far future. Since the process being released can't be signaled
any longer, it remains and waits for the echo-back event in that far
future.
Back to history, the draining feature was implemented at the time we
misinterpreted POSIX definition for blocking file operation.
Actually, such a behavior is superfluous at release, and we should
just release the device as is instead of keeping it up forever.
This patch just removes the draining call that may block the release
for too long time unexpectedly.
BugLink: http://lkml.kernel.org/r/CACT4Y+Y4kD-aBGj37rf-xBw9bH3GMU6P+MYg4W1e-s-paVD2pg@mail.gmail.com
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 513ace79b657e2022a592e77f24074e088681ecc upstream.
X32 ABI uses the 64bit timespec in addition to 64bit alignment of
64bit values. This leads to incompatibilities in some PCM ioctls
involved with snd_pcm_channel_info, snd_pcm_status and
snd_pcm_sync_ptr structs. Fix the PCM compat ABI for these ioctls
like the previous commit for ctl API.
Reported-by: Steven Newbury <steve@snewbury.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b24e7ad1fdc22177eb3e51584e1cfcb45d818488 upstream.
X32 ABI takes the 64bit timespec, thus the timer user status ioctl becomes
incompatible with IA32. This results in NOTTY error when the ioctl is
issued.
Meanwhile, this struct in X32 is essentially identical with the one in
X86-64, so we can just bypassing to the existing code for this
specific compat ioctl.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2251fbbc1539f05b0b206b37a602d5776be37252 upstream.
Like the previous fixes for ctl and PCM, we need a fix for
incompatible X32 ABI regarding the rawmidi: namely, struct
snd_rawmidi_status has the timespec, and the size and the alignment on
X32 differ from IA32.
This patch fixes the incompatible ioctl for X32.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 02322ac9dee9aff8d8862e8d6660ebe102f492ea upstream.
This patch applies the microphone-related fix created for the Acer
Aspire E1-572 to the E1-472 as well, as it uses the same Realtek ALC282
CODEC and demonstrates the same issues.
This patch allows an external, headset microphone to be used and limits
the gain on the (quite noisy) internal microphone.
Signed-off-by: Simon South <simon@simonsouth.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6236d8bb2afcfe71b88ecea554e0dc638090a45f upstream.
The X32 ABI takes the same alignment like x86-64, and this may result
in the incompatible struct size from ia32. Unfortunately, we hit this
in some control ABI: struct snd_ctl_elem_value differs between them
due to the position of 64bit variable array. This ends up with the
unknown ioctl (ENOTTY) error.
The fix is to add the compat entries for the new aligned struct.
Reported-and-tested-by: Steven Newbury <steve@snewbury.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 17e2df4613be57d0fab68df749f6b8114e453152 upstream.
Plantronics DA45 does not support reading the sample rate which leads
to many lines of "cannot get freq at ep 0x4" and "cannot get freq at
ep 0x84". This patch adds the USB ID of the DA45 to quirks.c and
avoids those error messages.
Signed-off-by: Dennis Kadioglu <denk@post.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ba4581c84cfb39fd527f6b3457f1c97f6356c04 upstream.
The 5 volt detect functionality broke in 3.14: the code reads IO register 0x70
again after it has already been cleared. Instead it should use the cached
irq_reg_0x70 value and the io_write to 0x71 to clear 0x70 can be dropped since
this has already been done.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f16921275cc3c2442d0b95225785a601603b990f upstream.
While testing audio with pxa2xx-ac97, underrun were happening while the
user application was correctly feeding the music. Debug proved that the
cyclic transfer is not cyclic, ie. the last descriptor did not loop on
the first.
Another issue is that the descriptor length was always set to 8192,
because of an trivial operator issue.
This was tested on a pxa27x platform.
Fixes: a57e16cf03 ("dmaengine: pxa: add pxa dmaengine driver")
Reported-by: Vasily Khoruzhick <anarsoul@gmail.com>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be629c62a603e5935f8177fd8a19e014100a259e upstream.
When a directory is deleted, we don't take too much care about killing off
all the dirents that belong to it — on the basis that on remount, the scan
will conclude that the directory is dead anyway.
This doesn't work though, when the deleted directory contained a child
directory which was moved *out*. In the early stages of the fs build
we can then end up with an apparent hard link, with the child directory
appearing both in its true location, and as a child of the original
directory which are this stage of the mount process we don't *yet* know
is defunct.
To resolve this, take out the early special-casing of the "directories
shall not have hard links" rule in jffs2_build_inode_pass1(), and let the
normal nlink processing happen for directories as well as other inodes.
Then later in the build process we can set ic->pino_nlink to the parent
inode#, as is required for directories during normal operaton, instead
of the nlink. And complain only *then* about hard links which are still
in evidence even after killing off all the unreachable paths.
Reported-by: Liu Song <liu.song11@zte.com.cn>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 49e91e7079febe59a20ca885a87dd1c54240d0f1 upstream.
With this fix, all code paths should now be obtaining the page lock before
f->sem.
Reported-by: Szabó Tamás <sztomi89@gmail.com>
Tested-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 157078f64b8a9cd7011b6b900b2f2498df850748 upstream.
This reverts commit 5ffd3412ae
("jffs2: Fix lock acquisition order bug in jffs2_write_begin").
The commit modified jffs2_write_begin() to remove a deadlock with
jffs2_garbage_collect_live(), but this introduced new deadlocks found
by multiple users. page_lock() actually has to be called before
mutex_lock(&c->alloc_sem) or mutex_lock(&f->sem) because
jffs2_write_end() and jffs2_readpage() are called with the page locked,
and they acquire c->alloc_sem and f->sem, resp.
In other words, the lock order in jffs2_write_begin() was correct, and
it is the jffs2_garbage_collect_live() path that has to be changed.
Revert the commit to get rid of the new deadlocks, and to clear the way
for a better fix of the original deadlock.
Reported-by: Deng Chao <deng.chao1@zte.com.cn>
Reported-by: Ming Liu <liu.ming50@gmail.com>
Reported-by: wangzaiwei <wangzaiwei@top-vision.cn>
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 909c3a22da3b8d2cfd3505ca5658f0176859d400 upstream.
When looking for orphan roots during mount we can end up hitting a
BUG_ON() (at root-item.c:btrfs_find_orphan_roots()) if a log tree is
replayed and qgroups are enabled. This is because after a log tree is
replayed, a transaction commit is made, which triggers qgroup extent
accounting which in turn does backref walking which ends up reading and
inserting all roots in the radix tree fs_info->fs_root_radix, including
orphan roots (deleted snapshots). So after the log tree is replayed, when
finding orphan roots we hit the BUG_ON with the following trace:
[118209.182438] ------------[ cut here ]------------
[118209.183279] kernel BUG at fs/btrfs/root-tree.c:314!
[118209.184074] invalid opcode: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
[118209.185123] Modules linked in: btrfs dm_flakey dm_mod crc32c_generic ppdev xor raid6_pq evdev sg parport_pc parport acpi_cpufreq tpm_tis tpm psmouse
processor i2c_piix4 serio_raw pcspkr i2c_core button loop autofs4 ext4 crc16 mbcache jbd2 sd_mod sr_mod cdrom ata_generic virtio_scsi ata_piix libata
virtio_pci virtio_ring virtio scsi_mod e1000 floppy [last unloaded: btrfs]
[118209.186318] CPU: 14 PID: 28428 Comm: mount Tainted: G W 4.5.0-rc5-btrfs-next-24+ #1
[118209.186318] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS by qemu-project.org 04/01/2014
[118209.186318] task: ffff8801ec131040 ti: ffff8800af34c000 task.ti: ffff8800af34c000
[118209.186318] RIP: 0010:[<ffffffffa04237d7>] [<ffffffffa04237d7>] btrfs_find_orphan_roots+0x1fc/0x244 [btrfs]
[118209.186318] RSP: 0018:ffff8800af34faa8 EFLAGS: 00010246
[118209.186318] RAX: 00000000ffffffef RBX: 00000000ffffffef RCX: 0000000000000001
[118209.186318] RDX: 0000000080000000 RSI: 0000000000000001 RDI: 00000000ffffffff
[118209.186318] RBP: ffff8800af34fb08 R08: 0000000000000001 R09: 0000000000000000
[118209.186318] R10: ffff8800af34f9f0 R11: 6db6db6db6db6db7 R12: ffff880171b97000
[118209.186318] R13: ffff8801ca9d65e0 R14: ffff8800afa2e000 R15: 0000160000000000
[118209.186318] FS: 00007f5bcb914840(0000) GS:ffff88023edc0000(0000) knlGS:0000000000000000
[118209.186318] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[118209.186318] CR2: 00007f5bcaceb5d9 CR3: 00000000b49b5000 CR4: 00000000000006e0
[118209.186318] Stack:
[118209.186318] fffffbffffffffff 010230ffffffffff 0101000000000000 ff84000000000000
[118209.186318] fbffffffffffffff 30ffffffffffffff 0000000000000101 ffff880082348000
[118209.186318] 0000000000000000 ffff8800afa2e000 ffff8800afa2e000 0000000000000000
[118209.186318] Call Trace:
[118209.186318] [<ffffffffa042e2db>] open_ctree+0x1e37/0x21b9 [btrfs]
[118209.186318] [<ffffffffa040a753>] btrfs_mount+0x97e/0xaed [btrfs]
[118209.186318] [<ffffffff8108e1c0>] ? trace_hardirqs_on+0xd/0xf
[118209.186318] [<ffffffff8117b87e>] mount_fs+0x67/0x131
[118209.186318] [<ffffffff81192d2b>] vfs_kern_mount+0x6c/0xde
[118209.186318] [<ffffffffa0409f81>] btrfs_mount+0x1ac/0xaed [btrfs]
[118209.186318] [<ffffffff8108e1c0>] ? trace_hardirqs_on+0xd/0xf
[118209.186318] [<ffffffff8108c26b>] ? lockdep_init_map+0xb9/0x1b3
[118209.186318] [<ffffffff8117b87e>] mount_fs+0x67/0x131
[118209.186318] [<ffffffff81192d2b>] vfs_kern_mount+0x6c/0xde
[118209.186318] [<ffffffff81195637>] do_mount+0x8a6/0x9e8
[118209.186318] [<ffffffff8119598d>] SyS_mount+0x77/0x9f
[118209.186318] [<ffffffff81493017>] entry_SYSCALL_64_fastpath+0x12/0x6b
[118209.186318] Code: 64 00 00 85 c0 89 c3 75 24 f0 41 80 4c 24 20 20 49 8b bc 24 f0 01 00 00 4c 89 e6 e8 e8 65 00 00 85 c0 89 c3 74 11 83 f8 ef 75 02 <0f> 0b
4c 89 e7 e8 da 72 00 00 eb 1c 41 83 bc 24 00 01 00 00 00
[118209.186318] RIP [<ffffffffa04237d7>] btrfs_find_orphan_roots+0x1fc/0x244 [btrfs]
[118209.186318] RSP <ffff8800af34faa8>
[118209.230735] ---[ end trace 83938f987d85d477 ]---
So fix this by not treating the error -EEXIST, returned when attempting
to insert a root already inserted by the backref walking code, as an error.
The following test case for xfstests reproduces the bug:
seq=`basename $0`
seqres=$RESULT_DIR/$seq
echo "QA output created by $seq"
tmp=/tmp/$$
status=1 # failure is the default!
trap "_cleanup; exit \$status" 0 1 2 3 15
_cleanup()
{
_cleanup_flakey
cd /
rm -f $tmp.*
}
# get standard environment, filters and checks
. ./common/rc
. ./common/filter
. ./common/dmflakey
# real QA test starts here
_supported_fs btrfs
_supported_os Linux
_require_scratch
_require_dm_target flakey
_require_metadata_journaling $SCRATCH_DEV
rm -f $seqres.full
_scratch_mkfs >>$seqres.full 2>&1
_init_flakey
_mount_flakey
_run_btrfs_util_prog quota enable $SCRATCH_MNT
# Create 2 directories with one file in one of them.
# We use these just to trigger a transaction commit later, moving the file from
# directory a to directory b and doing an fsync against directory a.
mkdir $SCRATCH_MNT/a
mkdir $SCRATCH_MNT/b
touch $SCRATCH_MNT/a/f
sync
# Create our test file with 2 4K extents.
$XFS_IO_PROG -f -s -c "pwrite -S 0xaa 0 8K" $SCRATCH_MNT/foobar | _filter_xfs_io
# Create a snapshot and delete it. This doesn't really delete the snapshot
# immediately, just makes it inaccessible and invisible to user space, the
# snapshot is deleted later by a dedicated kernel thread (cleaner kthread)
# which is woke up at the next transaction commit.
# A root orphan item is inserted into the tree of tree roots, so that if a
# power failure happens before the dedicated kernel thread does the snapshot
# deletion, the next time the filesystem is mounted it resumes the snapshot
# deletion.
_run_btrfs_util_prog subvolume snapshot $SCRATCH_MNT $SCRATCH_MNT/snap
_run_btrfs_util_prog subvolume delete $SCRATCH_MNT/snap
# Now overwrite half of the extents we wrote before. Because we made a snapshpot
# before, which isn't really deleted yet (since no transaction commit happened
# after we did the snapshot delete request), the non overwritten extents get
# referenced twice, once by the default subvolume and once by the snapshot.
$XFS_IO_PROG -c "pwrite -S 0xbb 4K 8K" $SCRATCH_MNT/foobar | _filter_xfs_io
# Now move file f from directory a to directory b and fsync directory a.
# The fsync on the directory a triggers a transaction commit (because a file
# was moved from it to another directory) and the file fsync leaves a log tree
# with file extent items to replay.
mv $SCRATCH_MNT/a/f $SCRATCH_MNT/a/b
$XFS_IO_PROG -c "fsync" $SCRATCH_MNT/a
$XFS_IO_PROG -c "fsync" $SCRATCH_MNT/foobar
echo "File digest before power failure:"
md5sum $SCRATCH_MNT/foobar | _filter_scratch
# Now simulate a power failure and mount the filesystem to replay the log tree.
# After the log tree was replayed, we used to hit a BUG_ON() when processing
# the root orphan item for the deleted snapshot. This is because when processing
# an orphan root the code expected to be the first code inserting the root into
# the fs_info->fs_root_radix radix tree, while in reallity it was the second
# caller attempting to do it - the first caller was the transaction commit that
# took place after replaying the log tree, when updating the qgroup counters.
_flakey_drop_and_remount
echo "File digest before after failure:"
# Must match what he got before the power failure.
md5sum $SCRATCH_MNT/foobar | _filter_scratch
_unmount_flakey
status=0
exit
Fixes: 2d9e977610 ("Btrfs: use btrfs_get_fs_root in resolve_indirect_ref")
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 018361767a21fb2d5ebd3ac182c04baf8a8b4e08 upstream.
The RB532 platform specific irq_to_gpio() implementation has been
removed with commit 832f5dacfa ("MIPS: Remove all the uses of
custom gpio.h"). Now the platform uses the generic stub which causes
the following error:
pata-rb532-cf pata-rb532-cf: no GPIO found for irq149
pata-rb532-cf: probe of pata-rb532-cf failed with error -2
Drop the irq_to_gpio() call and get the GPIO number from platform
data instead. After this change, the driver works again:
scsi host0: pata-rb532-cf
ata1: PATA max PIO4 irq 149
ata1.00: CFA: CF 1GB, 20080820, max MWDMA4
ata1.00: 1989792 sectors, multi 0: LBA
ata1.00: configured for PIO4
scsi 0:0:0:0: Direct-Access ATA CF 1GB 0820 PQ: 0\
ANSI: 5
sd 0:0:0:0: [sda] 1989792 512-byte logical blocks: (1.01 GB/971 MiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't\
support DPO or FUA
sda: sda1 sda2
sd 0:0:0:0: [sda] Attached SCSI disk
Fixes: 832f5dacfa ("MIPS: Remove all the uses of custom gpio.h")
Cc: Alban Bedel <albeu@free.fr>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e57cbaf0eb006eaa207395f3bfd7ce52c1b5539c upstream.
Commit 9f61668073 "tracing: Allow triggers to filter for CPU ids and
process names" added a 'comm' filter that will filter events based on the
current tasks struct 'comm'. But this now hides the ability to filter events
that have a 'comm' field too. For example, sched_migrate_task trace event.
That has a 'comm' field of the task to be migrated.
echo 'comm == "bash"' > events/sched_migrate_task/filter
will now filter all sched_migrate_task events for tasks named "bash" that
migrates other tasks (in interrupt context), instead of seeing when "bash"
itself gets migrated.
This fix requires a couple of changes.
1) Change the look up order for filter predicates to look at the events
fields before looking at the generic filters.
2) Instead of basing the filter function off of the "comm" name, have the
generic "comm" filter have its own filter_type (FILTER_COMM). Test
against the type instead of the name to assign the filter function.
3) Add a new "COMM" filter that works just like "comm" but will filter based
on the current task, even if the trace event contains a "comm" field.
Do the same for "cpu" field, adding a FILTER_CPU and a filter "CPU".
Fixes: 9f61668073 "tracing: Allow triggers to filter for CPU ids and process names"
Reported-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc8b4afc4a04fac8ee55a19b59f2356a25e7e778 upstream.
The HPCP bit is set by bioses for on-board sata ports either because
they think sata is hotplug capable in general or to allow Windows
to display a "device eject" icon on ports which are routed to an
external connector bracket.
However in Redhat Bugzilla #1310682, users report that with kernel 4.4,
where this bit test first appeared, a lot of partitions on sata drives
are now mounted automatically.
This patch should fix redhat and a lot of other distros which
unconditionally automount all devices which have the "removable"
bit set.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: 8a3e33cf92 ("ata: ahci: find eSATA ports and flag them as removable" changes userspace behavior)
Link: http://lkml.kernel.org/g/56CF35FA.1070500@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92f9e179a702a6adbc11e2fedc76ecd6ffc9e3f7 upstream.
Pause/unpause graph tracing around do_suspend_lowlevel as it has
inconsistent call/return info after it jumps to the wakeup vector.
The graph trace buffer will otherwise become misaligned and
may eventually crash and hang on suspend.
To reproduce the issue and test the fix:
Run a function_graph trace over suspend/resume and set the graph
function to suspend_devices_and_enter. This consistently hangs the
system without this fix.
Signed-off-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dfd55ad85e4a7fbaa82df12467515ac3c81e8a3e upstream.
Commit dd006da216 ("arm64: mm: increase VA range of identity map") made
some changes to the memory mapping code to allow physical memory to reside
at an offset that exceeds the size of the virtual mapping.
However, since the size of the vmemmap area is proportional to the size of
the VA area, but it is populated relative to the physical space, we may
end up with the struct page array being mapped outside of the vmemmap
region. For instance, on my Seattle A0 box, I can see the following output
in the dmesg log.
vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000 ( 8 GB maximum)
0xffffffbfc0000000 - 0xffffffbfd0000000 ( 256 MB actual)
We can fix this by deciding that the vmemmap region is not a projection of
the physical space, but of the virtual space above PAGE_OFFSET, i.e., the
linear region. This way, we are guaranteed that the vmemmap region is of
sufficient size, and we can even reduce the size by half.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f5bdd66c705484b4bc77eb914be15c1b7881fae7 upstream.
This patch complements the list of device IDs previously
added for lewisburg sata.
Signed-off-by: Alexandra Yates <alexandra.yates@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a1a0e23e49037c23ea84bc8cc146a03584d13577 upstream.
If cgroup writeback is in use, inodes can be scheduled for
asynchronous wb switching. Before 5ff8eaac1636 ("writeback: keep
superblock pinned during cgroup writeback association switches"), this
could race with umount leading to super_block being destroyed while
inodes are pinned for wb switching. 5ff8eaac1636 fixed it by bumping
s_active while wb switches are in flight; however, this allowed
in-flight wb switches to make umounts asynchronous when the userland
expected synchronosity - e.g. fsck immediately following umount may
fail because the device is still busy.
This patch removes the problematic super_block pinning and instead
makes generic_shutdown_super() flush in-flight wb switches. wb
switches are now executed on a dedicated isw_wq so that they can be
flushed and isw_nr_in_flight keeps track of the number of in-flight wb
switches so that flushing can be avoided in most cases.
v2: Move cgroup_writeback_umount() further below and add MS_ACTIVE
check in inode_switch_wbs() as Jan an Al suggested.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Tahsin Erdogan <tahsin@google.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Link: http://lkml.kernel.org/g/CAAeU0aNCq7LGODvVGRU-oU_o-6enii5ey0p1c26D1ZzYwkDc5A@mail.gmail.com
Fixes: 5ff8eaac1636 ("writeback: keep superblock pinned during cgroup writeback association switches")
Reviewed-by: Jan Kara <jack@suse.cz>
Tested-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7bcd79ac50d9d83350a835bdb91c04ac9e098412 upstream.
The bio passed to bio_will_gap() may be fast cloned from upper
layer(dm, md, bcache, fs, ...), or from bio splitting in block
core.
Unfortunately bio_will_gap() just figures out the last bvec via
'bi_io_vec[prev->bi_vcnt - 1]' directly, and this way is obviously
wrong.
This patch introduces two helpers for getting the first and last
bvec of one bio for fixing the issue.
Reported-by: Sagi Grimberg <sagig@dev.mellanox.co.il>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ee34ea3a12396f35b26d90a094c75db95080baa upstream.
The id buffer in ata_device is a DMA target, but it isn't explicitly
cacheline aligned. Due to this, adjacent fields can be overwritten with
stale data from memory on non coherent architectures. As a result, the
kernel is sometimes unable to communicate with an ATA device.
Fix this by ensuring that the id buffer is cacheline aligned.
This issue is similar to that fixed by Commit 84bda12af3
("libata: align ap->sector_buf").
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
