QCA988X firmware starting from 10.2.4.70.12-2 supports new
vdev subtypes for proxy STA and Mesh, hence add them to be used
as needed.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Update WMI 10.x service map to sync with firmware 10.2.4.70.12-2
released on 11/11/2015 which is the latest QCA988X firmware as of
11/18/2015.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix write permission for few of the debugfs entries
which support write file operations as well.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Allocations from the DMA zone were originally added for legacy ISA
stuff, or PCI devices that have specific limitations in their DMA
addressing capabilities. It has no place in ath10k, which can do
full 32-bit DMA.
Fixes memory allocation errors on some platforms.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable AP + STA interface combination support for 10.x and
this enables Repeater mode testing (with WDS Repeater combinations
as well). Fix indentation as well.
Based on the suggestions from Michal and Yanbo Li,
thanks to them
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The error message order of board data fetch is board info,
directory, and then file name, hence place print arguments
in the order.
Fixes: 0a51b343ab ("ath10k: add board 2 API support")
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
After commit cf4f21938e13 ("kbuild: Allow to specify composite modules
with modname-m"), thermal.c gets included in the driver and the build
fails with
drivers/net/wireless/ath/ath10k/thermal.c:119:6: error: redefinition of ‘ath10k_thermal_event_temperature’
drivers/net/wireless/ath/ath10k/thermal.h:54:20: note: previous definition of ‘ath10k_thermal_event_temperature’ was here
drivers/net/wireless/ath/ath10k/thermal.c:136:6: error: redefinition of ‘ath10k_thermal_set_throttling’
drivers/net/wireless/ath/ath10k/thermal.h:59:20: note: previous definition of ‘ath10k_thermal_set_throttling’ was here
drivers/net/wireless/ath/ath10k/thermal.c:162:5: error: redefinition of ‘ath10k_thermal_register’
drivers/net/wireless/ath/ath10k/thermal.h:45:19: note: previous definition of ‘ath10k_thermal_register’ was here
drivers/net/wireless/ath/ath10k/thermal.c:216:6: error: redefinition of ‘ath10k_thermal_unregister’
drivers/net/wireless/ath/ath10k/thermal.h:50:20: note: previous definition of ‘ath10k_thermal_unregister’ was here
Change the #ifdef to reflect the new kbuild behavior.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Michal Marek <mmarek@suse.com>
Txbuf is no longer a DMA pool and can be easily
tracked with a mere msdu_id. This saves 10 bytes
on 64bit systems and 6 bytes on 32bit systems of
precious sk_buff control buffer.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This prepares the driver for future ieee80211_txq
and wake_tx_queue() support.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Frames are not guaranteed to be 802.11 frames in
ath10k_htt_tx() and the tx completion handler.
In some cases, like TDLS, they can be Ethernet.
Hence checking, e.g. frame_control could yield
bogus results and behavior.
Fortunately this wasn't a real problem so far
because there's no FW/HW combination to encounter
this problem.
However it is good to fix this in advance.
Fixes: 75d85fd999 ("ath10k: introduce basic tdls functionality")
Fixes: eebc67fef3 ("ath10k: fix pmf for wmi-tlv on qca6174")
Fixes: 7b7da0a021 ("ath10k: drop probe responses when too many are queued")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was wasteful to have all the flags as separate
bools.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was wasteful to keep it in the struct because
it can be passed as function argument down the tx
path.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
All functions should have ath10k_{filename}_
prefixes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was wasteful to have two flags describing
the same thing.
While at it fix code style of
ath10k_tx_h_use_hwcrypto().
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The QCA99X0 4 addresses RX packets pad 2 bytes at the beginning of
MSDU instead the end of ieee80211 header to keep alignment. The currently RX
data path can't parse the header correctly in this case. This patch fixes it
for QCA99X0.
Signed-off-by: Yanbo Li <yanbol@qca.qualcomm.com>
[kvalo@qca.qualcomm.com: checkpatch fixes and naming changes]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The RX rate idx is not correct for 11G mode OFDM packet.
Because the bitrate table start with CCK index instead of OFDM.
Signed-off-by: Yanbo Li <yanbol@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Of a word in struct htt_data_tx_desc htt version >= 3.4 firmware uses
LSB 16-bit for frequency configuration which is used for offchannel tx
and MSB 16-bit is for peerid. But other firmwares using version 2.X
(10.1, 10.2.2, 10.2.4 and 10.4) are using 32-bit for peerid in htt tx
desc. So far no issue is found with the existing code setting peerid and
freq for HTT version 2.X, this could be mainly because of 0 as frequecy
(home channel) is being always passed with those firmwares. There may be
issues when non-zero freq is passed with firmware using < 3.4 htt version.
To be safe use target_version_major and target_version_minor along with
htt-op-version before configuring peer id and freq in htt tx desc. This
patch extends ath10k_mac_tx_frm_has_freq() to check for htt_op_version_tlv
and uses the helper while setting peerid in htt_tx_desc.
Fixes: 8d6d362436 ("ath10k: fix offchan reliability")
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rename ath10k_mac_need_offchan_tx_work() to ath10k_mac_tx_frm_has_freq()
to make it more meaningful. This helper will be used in the future
change. No functionality change.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There is an extra 4-byte member when compared to WMI 10.2 added to
assoc complete command in WMI 10.4. This new member is used for 160Mhz
related configuration. This WMI command mismatch between host and
firmware does not cause any real issues because this new member is not
used in 10.4 firmwares so far (10.4.1.00030-1). This difference in WMI
command interface brings in a new wmi_ops for 10.4 gen_peer_assoc().
No noticeable functionality differences with this change can be seen
with the current 10.4 firmwares, but the WMI interface has to be
fixed to work with future 10.4 firmwares which may be using this new
member.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds pktlog support for 10.4 fw versions.
Change-Id: Idf8c04dbc0da427dabbeb09b91e328ee1730dc80
Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
As not all QCA98XX radios are not connected to Bluetooth modules, enabling the
BT coex feature in firmware will have side effects if the radio's GPIO are
connected with other (non-BT) HW modules. Add debugfs file to control the
firmware BT coex logic and set the feature as disable by default to avoid that
btcoex is accidentally enabled.
To enable this feature, execute:
echo 1 > /sys/kernel/debug/ieee80211/phyX/ath10k/btcoex
To disable:
echo 0 > /sys/kernel/debug/ieee80211/phyX/ath10k/btcoex
The firmware support this feature since 10.2.4.54 on 2G-only board, dual band
or 5G boards don't support this. The feature's name is WMI_SERVICE_COEX_GPIO
and the btcoex file is not created if firmware doesn't support it.
Signed-off-by: Yanbo Li <yanbol@qca.qualcomm.com>
[kvalo@qca.qualcomm.com: use btcoex filename and other smaller fixes]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
No functionality change, just sync to the latest
pdev params that 10.4 firmware defines.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
No real functionality change, add WMI command/event
defines to be in sync with 10.4 firmware.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
No functional changes, adds new wmi service bits for
10.4 firmware to be sync with 10.4 firmware.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch enables thermal throttling support for 10.4 firmware.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Set peer's management frame protection flag in peer assoc command,
this setting will enable/disable encrytion of management frames in fw.
Setting of this flag is based on whether MFP is enabled/disabled at STA
and a firmware feature flag ATH10K_FW_FEATURE_MFP_SUPPORT. This is because
only firmwares 10.1.561 and above have support for MFP.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Manikanta pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Abstraction layer for peer flags is added to fix ABI breakage.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: SenthilKumar Jegadeesan <sjegadee@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch replaces multiple if conditional checks with a single if condition
in WMI management rx handler. Found during code review.
Signed-off-by: Manikanta Pubbisetty <manikanta.pubbisetty@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add support for WDSP, SPI used for CPE.
Update pm660a internal codec files to disable
external codec nodes. Also update external codec
CDP and RCM headset jack properties to use
NC(Normally Closed) type.
CRs-Fixed: 1094763
Change-Id: Ib45c13ab56323aef667aac588b2c22384a573a14
Signed-off-by: Laxminath Kasam <lkasam@codeaurora.org>
Currently enabling of Qnovo isn't allowed unless a charger with
minimum 1A current limit is detected. This is not required.
Allow enabling of Qnovo regardless of the charger current limit.
Change-Id: I1726423d3bc31725c162f09b907683d6e63ac6b5
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
OSM cpu clocks would require the supply rails on which power and perf
clusters are connected, so add the same.
Change-Id: Ie5e50dff1c3c5b06585d03abb45ff493779f029d
Signed-off-by: Taniya Das <tdas@codeaurora.org>
GPIO7 is used for volume up key on qrd sdm660 device.
Configure it to input and pull-up and add gpio-keys device to
enable the key detection.
CRs-Fixed: 1108198
Change-Id: I9ef323088e478aa2fd35858d256edb041da6f385
Signed-off-by: cyizhao <cyizhao@codeaurora.org>
Add battery profile for qrd sdm660 to make sure FG could load it
and work as expected.
Disable soft hot jeita threshold according to the battery vendor's and
hardware team's suggestion to make sure the battery could sustain at 1C
charging current longer.
CRs-Fixed: 1108198
Change-Id: Ifebeadae1590813ad785d25a399011efb447746d
Signed-off-by: cyizhao <cyizhao@codeaurora.org>
The documentation for schedule_timeout(), schedule_hrtimeout(), and
schedule_hrtimeout_range() all claim that the routines couldn't possibly
return early if the task state was TASK_UNINTERRUPTIBLE. This is simply
not true since wake_up_process() will cause those routines to exit early.
We cannot make schedule_[hr]timeout() loop until the timeout expires if the
task state is uninterruptible because we have users which rely on the
existing and designed behaviour.
Make the documentation match the (correct) implementation.
schedule_hrtimeout() returns -EINTR even when a uninterruptible task was
woken up. This might look strange, but making the return code depend on the
state is too much of an effort as it would affect all the call sites. There
is no value in doing so, but we spell it out clearly in the documentation.
Change-Id: I3e9bf91e7d285abcac134e32b02131b999d79f40
Suggested-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Cc: huangtao@rock-chips.com
Cc: heiko@sntech.de
Cc: broonie@kernel.org
Cc: briannorris@chromium.org
Cc: Andreas Mohr <andi@lisas.de>
Cc: linux-rockchip@lists.infradead.org
Cc: tony.xie@rock-chips.com
Cc: John Stultz <john.stultz@linaro.org>
Cc: linux@roeck-us.net
Cc: tskd08@gmail.com
Link: http://lkml.kernel.org/r/1477065531-30342-2-git-send-email-dianders@chromium.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Git-commit: 4b7e9cf9c84b09adc428e0433cd376b91f9c52a7
Git-repo: git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git
Signed-off-by: Runmin Wang <runminw@codeaurora.org>
Users of usleep_range() expect that it will _never_ return in less time
than the minimum passed parameter. However, nothing in the code ensures
this, when the sleeping task is woken by wake_up_process() or any other
mechanism which can wake a task from uninterruptible state.
Neither usleep_range() nor schedule_hrtimeout_range*() have any protection
against wakeups. schedule_hrtimeout_range*() is designed this way despite
the fact that the API documentation does not mention it.
msleep() already has code to handle this case since it will loop as long
as there was still time left. usleep_range() has no such loop, add it.
Presumably this problem was not detected before because usleep_range() is
only used in a few places and the function is mostly used in contexts which
are not exposed to wakeups of any form.
An effort was made to look for users relying on the old behavior by
looking for usleep_range() in the same file as wake_up_process().
No problems were found by this search, though it is conceivable that
someone could have put the sleep and wakeup in two different files.
An effort was made to ask several upstream maintainers if they were aware
of people relying on wake_up_process() to wake up usleep_range(). No
maintainers were aware of that but they were aware of many people relying
on usleep_range() never returning before the minimum.
Change-Id: Ia403f0dc9cac711c8a4b6fcc4cf0094ad1358ed7
Reported-by: Tao Huang <huangtao@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Cc: heiko@sntech.de
Cc: broonie@kernel.org
Cc: briannorris@chromium.org
Cc: Andreas Mohr <andi@lisas.de>
Cc: linux-rockchip@lists.infradead.org
Cc: tony.xie@rock-chips.com
Cc: John Stultz <john.stultz@linaro.org>
Cc: djkurtz@chromium.org
Cc: linux@roeck-us.net
Cc: tskd08@gmail.com
Link: http://lkml.kernel.org/r/1477065531-30342-1-git-send-email-dianders@chromium.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Git-commit: 6c5e9059692567740a4ee51530dffe51a4b9584d
Git-repo: git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git
Signed-off-by: Runmin Wang <runminw@codeaurora.org>
Linus noticed that lock_timer_base() lacks a READ_ONCE() for accessing the
timer flags. As a consequence the compiler is allowed to reload the flags
between the initial check for TIMER_MIGRATION and the following timer base
computation and the spin lock of the base.
While this has not been observed (yet), we need to make sure that it never
happens.
Change-Id: I577327e02ab77b6de951ac2aa936cb5d5a4f477a
Fixes: 0eeda71bc3 ("timer: Replace timer base by a cpu index")
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1610241711220.4983@nanos
Cc: stable@vger.kernel.org
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Git-commit: b831275a3553c32091222ac619cfddd73a5553fb
Git-repo: git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git
[runminw@codeaurora.org: resolve trivial merge conflicts]
Signed-off-by: Runmin Wang <runminw@codeaurora.org>
Keep gcc_bimc_gfx_clk always on to prevent a stall during BIMC
redirection handshake that occurs as part of a transition between
different CCI power modes. The stall causes momentary bandwidth drops
for the display ports and creates display buffer underflows.
Change-Id: Ie7de487fbe16c7e6b1234a96c1208d54daa5a9bb
Signed-off-by: David Dai <daidavid1@codeaurora.org>
The format specifier %p can leak kernel addresses
while not valuing the kptr_restrict system settings.
Use %pK instead of %p, which also evaluates whether
kptr_restrict is set.
Bug: 31796940
Change-Id: Ia2946d6b493126d68281f97778faf578247f088e
Signed-off-by: Min Chong <mchong@google.com>
[d-cagle@codeaurora.org: Resolve trivial merge conflicts]
Git-repo: https://android.googlesource.com/kernel/msm
Git-commit: 89220e920f99b7d87c086d6ea250c9f492712c3b
Signed-off-by: Dennis Cagle <d-cagle@codeaurora.org>
Format specifier %p can leak kernel addresses while not valuing the
kptr_restrict system settings. When kptr_restrict is set to (1), kernel
pointers printed using the %pK format specifier will be replaced with
Zeros. Debugging Note: &pK prints only Zeros as address. If you need
actual address information, write 0 to kptr_restrict.
echo 0 > /proc/sys/kernel/kptr_restrict
Change-Id: I4d65692f26e9c26dde98a80bb81f134225abaf16
Signed-off-by: Vamsi Krishna Samavedam <vskrishn@codeaurora.org>
Format specifier %p can leak kernel addresses while not valuing the
kptr_restrict system settings. When kptr_restrict is set to (1), kernel
pointers printed using the %pK format specifier will be replaced with
Zeros. Debugging Note : &pK prints only Zeros as address. If you need
actual address information, write 0 to kptr_restrict.
echo 0 > /proc/sys/kernel/kptr_restrict
Change-Id: I13175f66428ada62a2c011968ebc5a925519edbf
Signed-off-by: Vamsi Krishna Samavedam <vskrishn@codeaurora.org>
Format specifier %p can leak kernel addresses while not valuing the
kptr_restrict system settings. When kptr_restrict is set to (1), kernel
pointers printed using the %pK format specifier will be replaced with 0's.
Debugging Note : &pK prints only Zeros as address. If you need actual
address information, write 0 to kptr_restrict.
echo 0 > /proc/sys/kernel/kptr_restrict
Change-Id: If2177395082b81670af75712b945bea53a53915e
Signed-off-by: Vamsi Krishna Samavedam <vskrishn@codeaurora.org>
Format specifier %p can leak kernel addresses while not valuing the
kptr_restrict system settings. When kptr_restrict is set to (1), kernel
pointers printed using the %pK format specifier will be replaced with 0's.
Debugging Note : &pK prints only Zeros as address. If you need actual
address information, write 0 to kptr_restrict.
echo 0 > /proc/sys/kernel/kptr_restrict
Change-Id: Ice16947924f56b8f4244ae03b9ab4f2e36b7d56b
Signed-off-by: Vamsi Krishna Samavedam <vskrishn@codeaurora.org>
Format specifier %p can leak kernel addresses while not valuing the
kptr_restrict system settings. When kptr_restrict is set to (1), kernel
pointers printed using the %pK format specifier will be replaced with 0's.
Debugging Note : &pK prints only Zeros as address. If you need actual
address information, write 0 to kptr_restrict.
echo 0 > /proc/sys/kernel/kptr_restrict
Change-Id: Iaf20ac2175295dee8745c48f8c208a78b84dea91
Signed-off-by: Vamsi Krishna Samavedam <vskrishn@codeaurora.org>
Format specifier %p can leak kernel addresses while not valuing the
kptr_restrict system settings. When kptr_restrict is set to (1), kernel
pointers printed using the %pK format specifier will be replaced with 0's.
Debugging Note : &pK prints only Zeros as address. If you need actual
address information, write 0 to kptr_restrict.
echo 0 > /proc/sys/kernel/kptr_restrict
Change-Id: Ib1f9a151e3cb186763541dc86cb5b67a7d739ece
Signed-off-by: Vamsi Krishna Samavedam <vskrishn@codeaurora.org>
If MDP fence timeout happens, then to handle it gracefully
we stage border fill. In this regard as the mixer config has
now changed, then ctl flush has to be set.
Starting for Ia510fc6377c5b328cb4225a4725275d86b72dbff, ctl
flush bits were getting reset. Fix this in case mixer is
setup again with borderfill.
Change-Id: I12f60472e8f0f5630e239fb4b4026fda0d2f7cba
Signed-off-by: Jayant Shekhar <jshekhar@codeaurora.org>
Signed-off-by: Harsh Sahu <hsahu@codeaurora.org>
Add a level at the lower end of the memlat table for the Silver
cluster so that the memlat driver votes for at least 200MHz
when the CPU's effective frequency is at most 300MHz for latency
bound workloads.
Change-Id: I2695d2d115d925ac8b274d93e59b2be6578f3001
Signed-off-by: Rohit Gupta <rohgup@codeaurora.org>
Free all the SKP ION buffers that were locked for SPSS app swapping,
when remote subsystem reset.
Change-Id: I5230152cc7c3e721b1ebb01b663b9fd14bd2d6c9
Signed-off-by: Amir Samuelov <amirs@codeaurora.org>
Set moisture threshold values depending on the HW
configuration for NO Jack.
CRs-Fixed: 1099543
Change-Id: If995d462f1aeffb443471580520b1c8b5abca811
Signed-off-by: Yeleswarapu Nagaradhesh <nagaradh@codeaurora.org>
