ST-M41T0M6 is available on Colibri carrier boards.
Hence enable M41T0M6 RTC.
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds links to the on-chip SRAM and reset controller nodes
and switches the interrupts. Make the BIT processor interrupt, which exists on
all variants, the first one. The JPEG unit interrupt, which does not exist on
i.MX27 and i.MX5 thus is an optional second interrupt.
Use different compatible strings for i.MX6Q/D and i.MX6S/DL, as they have to
load separate firmware images for some reason.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
imx6q-tbs2910 board uses sgtl5000 codec and the machine file (imx-sgtl5000)
already sets SSI in slave mode and codec in master mode, so there is no need
for having this property.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Since restructuring of the device tree files, the USB misc/phy
nodes are disabled by default. Hence we need to enable those
explicitly when USB is used.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Use GPIO support by adding SD card detection configuration and
GPIO pinmux for Colibri's standard GPIO pins. Attach the GPIO
pins to the iomuxc node to get the GPIO pin settings applied.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Since pins and frequency are specific to module (pfla02), not base board
(pbab02), it is better to be initialized in corresponding dts file.
This patch fixes i2c2, i2c3 pin configuration which caused messages:
imx6q-pinctrl 20e0000.iomuxc: no groups defined in /soc/aips-bus@02000000/iomuxc@020e0000/i2c2grp
imx6q-pinctrl 20e0000.iomuxc: no groups defined in /soc/aips-bus@02000000/iomuxc@020e0000/i2c3grp
imx6q-pinctrl 20e0000.iomuxc: unable to find group for node i2c2grp
imx6q-pinctrl 20e0000.iomuxc: unable to find group for node i2c3grp
Signed-off-by: Dmitry Lavnikevich <d.lavnikevich@sam-solutions.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add Colibri VF50 device tree files vf500-colibri.dtsi and
vf500-colibri-eval-v3.dts, in line with the Colibri VF61 device tree
files. However, to minimize dupplication we also add vf-colibri.dtsi
and vf-colibri-eval-v3.dtsi which contain the common device tree
nodes.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This adds more generic base device trees for Vybrid SoCs. There
are three series of Vybrid SoC commonly available:
- VF3xx series: single core, Cortex-A5 without external memory
- VF5xx series: single core, Cortex-A5
- VF6xx series: dual core, Cortex-A5/Cortex-M4
The second digit represents the presents of a L2 cache (VFx1x).
The VF3xx series are not suitable for Linux especially since the
internal memory is quite small (1.5MiB).
The VF500 is essentially the base SoC, with only one core and
without L1 cache. The VF610 is a superset of the VF500, hence
vf500.dtsi is then included and enhanced by vf610.dtsi. There is
no board using VF510 or VF600 currently, but, if needed, they can
be added easily.
The Linux kernel can also run on the Cortex-M4 CPU of Vybrid
using !MMU support. This patchset creates a device tree structure
which allows to share peripherals nodes for a VF6xx Cortex-M4
device tree too. The two CPU types have different views of the
system: Foremost they are using different interrupt controllers,
but also the memory map is slightly different. The base device
tree vfxxx.dtsi allows to create SoC and board level device trees
supporting the Cortex-M4 while reusing the shared peripherals
nodes.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The clock controller module (CCM) has several clock inputs, which
are connected to external crystal oscillators. To reflect this,
assign these fixed clocks to the CCM node directly.
This especially resolves initialization order dependencies we had
with the earlier initialization code: When resolving of the fixed
clocks failed in clk-vf610, the code created fixed clocks with a
rate of 0.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The LS1021A TWR is a low cost, high-performance evaluation,
development and test platform supporting the LS1021A processor.
It is optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
For more detail information about the LS1021A TWR board, please
refer to LS1021A QorIQ Tower System Reference Manual.
Signed-off-by: Chao Fu <B44548@freescale.com>
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The LS1021A QorIQ development system (QDS) is a high-performance
computing evaluation, development and test platform supporting
the LS1021A processor. The LS1021A QDS is optimized to support
the high-bandwidth DDR3LP/DDR4 memory and a full complement of
high-speed SerDes ports.
For more detail information about the LS1021AQDS, please refer to
the QorIQ LS1021A Development System Reference Manual.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Chao Fu <B44548@freescale.com>
Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
On registration I2C bus drivers attemp to get ids from device tree
aliases, add a missing alias for I2C4 found on iMX6 DualLite/Solo.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
TBS2910 is a i.MX6Q based board. For additional details refer to
http://www.tbsdtv.com/products/tbs2910-matrix-arm-mini-pc.html
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add enet2 support for imx6sx-sdb board, and add the "fsl,imx6q-fec"
compatible for fec2 node to be compatible with the old version.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add all required properties for the cpufreq-dt driver.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The Colibri standard defines four pins as PWM outputs, two of them (PWM
A and C) are routed to FTM instance 0 and the other two (PWM B and D)
are routed to FTM instance 1. Hence enable both FTM instances for the
Colibri module and mux the four pins accordingly.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Add Global Timer support which is part of the private peripherals
of the Cortex-A5 processor. This Global Timer is compatible with the
Cortex-A9 implementation. It's a 64-bit timer and is clocked by the
peripheral clock, which is typically 133 or 166MHz on Vybrid.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
SSI block has 'ipg' clock for internal peripheral access and also 'baud' clock
for generating bit clock when SSI operates in master mode.
Add the extra 'baud' clock so that we can have SSI functional in master mode.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
SSI block has 'ipg' clock for internal peripheral access and also 'baud' clock
for generating bit clock when SSI operates in master mode.
Add the extra 'baud' clock so that we can have SSI functional in master mode.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Stock firmware on rk3288 does not initizalize the CNTVOFF registers
of the architected timer correctly. This introduces issues with the
newly added SMP support for rk3288, resulting in rcu stalls due to
differing timer values per core.
There exist preliminary and tested patches for u-boot for this problem,
but there are a minority of boards using other bootloaders like coreboot.
There also is currently a second solution for miss-initialized architected
timers in the works:
- clocksource: arch_timer: Fix code to use physical timers when requested
- clocksource: arch_timer: Allow the device tree to specify uninitialized timer registers
Therefore disable smp on rk3288 again till these are finalized, also
allowing coreboot-based boards to boot again.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
sclk_mfc is required for MFC device since commit
0c2272170d ("media: s5p-mfc: rename
special clock to sclk_mfc"), so add it to exynos4 dts.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This ensures the core and the audio subsystem clocks are configured
properly, as expected by the sound machine driver. These bits are
missing to obtain proper audio sample rates in kernel v3.17, where
audio support for Odroid X2/U3 was first added.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The HP Chromebook 11 uses an Atmel maXTouch as trackpad.
The keymap was found by trial-and-error.
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Spotted in the Chrome OS 3.8 based device tree.
Needs CONFIG_SENSORS_LM90.
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Reported-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds max77693-haptic node to support for haptic motor driver.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch add PWM(Pulse Width Modulation) node and
handle to use pwm property.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Specify the default mux and divider clocks in device tree
to ensure the FIMC devices on Trats, Trats2, Universal_c210
and Odroid X2/U3 boards are clocked from recommended clock
source and with maximum supported frequency.
For Trats2 also the MIPI-CSIS and the camera sensor clocks
are configured, the 'clock-frequency' property is deprecated
in favour of 'assigned-clock-rates' property.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch enables support for TMU at Exynos4412 based Trats2 board.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The TMU device tree node definition for Exynos4x12 family of SoCs.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Synology DS414 is a 4-bay NAS powered by a Marvell Armada XP
(mv78230 dual-core @1.33Ghz). It is very similar on many aspects
to previous 4-bay synology models based on Marvell kirkwood SoC.
Here is a short summary of the device:
- 1GB RAM
- Boot on SPI flash (64Mbit Micron N25Q064)
- 2 GbE interfaces (Armada MAC connected to two Marvell 88E1512
PHY via RGMII)
- 1 front USB 2.0 ports (directly handled by the Armada 370)
- 2 rear USB 3.0 ports (handled by an EtronTech EJ168A XHCI
controller on the PCIe bus)
- 4 internal SATA ports handled by a Marvell 88SX7042 SATA-II
controller on the PCIe bus)
- Seiko S-35390A I2C RTC chip
- UART0 providing serial console
- UART1 used for poweroff (connected to a Microchip PIC16F883)
Additional note: the front LEDs the and the two fans are not directly
connected to the SoC and under its control. The former are presumably
driven by the SATA controller, the latter by the PIC.
[ jac: fixed up s/ge[01]_rgmii_pins/pmx_ge[01]_rgmii/ to match
armada-xp.dtsi ]
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/5b678d6d1f2f42f4bf0d087878b9d8024d463ea7.1416613429.git.arno@natisbad.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Synology DS213j is a 2-bay NAS powered by a Marvell Armada 370
(88F6710 @1.2Ghz). It is very similar on many aspects to previous
2-bay synology models based on Marvell kirkwood SoC. Here is a
short summary of the device:
- 512MB RAM
- boot on SPI flash (64Mbit Micron N25Q064)
- 1 GbE interface (Armada MAC connected to a Marvell 88E1512
PHY via SGMII)
- 2 rear USB 2.0 ports (directly handled by the Armada 370)
- 2 internal SATA ports handled by the Armada 370: 2 GPIO for
presence, 2 for powering them
- two front amber LED (disk1, disk2) controlled by the SoC
- Seiko S-35390A I2C RTC chip
- UART0 providing serial console
- UART1 used for poweroff (connected to a TI MSP430F2111)
- Fan handled via 4 GPIO (3 for speed, 1 for alarm)
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/20f1a03897df1d825b62abdd525e588a8e39b3ec.1416613429.git.arno@natisbad.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch defines common Armada XP pinctrl settings in armada-xp.dtsi
for the supported SPI interface (MPP36-39) and use it as default
for Armada XP spi interface. That being done, it removes the now
redundant definitions in armada-xp-axpwifiap.dts.
Note: this patch has the potential to break out-of-tree users w/o
specific pinctrl settings for their spi interfaces if the default
above does not match their config (i.e. if they do not use CS0).
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/d404b7abd80ee5a0fd8e8d3586d33cd37740d589.1416613429.git.arno@natisbad.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch defines common Armada XP pinctrl settings for uart2 and
uart3 interfaces (uart0 and uart1 rx/tx do not rely on MPP):
uart2: MPP42-43 as default
uart3: MPP44-45 as default
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/fd51c080c7139a67ec01df8d797f1e88ce557796.1416613429.git.arno@natisbad.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch defines common Armada 370 pinctrl settings for uart0 and
uart1 interfaces:
uart0: MPP0-1 as default
uart1: MPP41-42 as default
Note: this patch has the potential to break out-of-tree users w/o
specific pinctrl settings for their uart interfaces if the default
above does not match their config.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/31412e57955c98bc9cc47b70726b5072af945cc3.1416613429.git.arno@natisbad.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch defines common Armada 370 pinctrl settings for spi0 and spi1
interfaces:
spi0: MPP33-36 as default, MPP32,63-65 as available alternate config
spi1: MPP49-52 as default
Currently, the Armada 370 DB .dts file has no explicit pinctrl info
for the spi0 interface used to access the flash on the board. The
patch fixes that by also adding explicit pinctrl info (MPP32,63-65)
for this SPI interface.
Note: this patch has the potential to break out-of-tree users w/o
specific pinctrl settings for their spi interfaces if the default
above does not match their config.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/1e812eb63b37718e273463e22e4d7512f8f0b624.1416613429.git.arno@natisbad.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
What was done by Sebastian in 264a05e19b ("ARM: mvebu: armada-xp:
Add node alias to pinctrl and add base address") and 01c434225e
("ARM: mvebu: armada-xp: Use pinctrl node alias") can also be done for
Armada 370, i.e.
- Rename Armada 370 pinctrl node to pin-ctrl with its address encoded
- Add a node alias to access the pinctrl node easily.
- use the newly available alias in existing Armada 370 .dts files
We can even go a bit further by putting the pinctrl node definition in
armada-370-xp.dtsi, with only its reg property defined. This allows us
to then also use the newly defined node alias in armada-xp.dtsi,
armada-370.dtsi.
Suggested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/b54eb45e5242728aace3ce8aef2eae4251f8dea3.1416613429.git.arno@natisbad.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that labels for uartX are available in Marvell Armada .dtsi files,
this patch replaces the "/soc/internal-regs/serial@12000" found in
armada-xp-lenovo-ix4-300d.dts file for stdout-path property by the more
concise &uart0.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/d1a883510e01f7f212a385e826dccbef903fae42.1416613429.git.arno@natisbad.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds uartX labels for Armada SoC serial nodes. This is
a preliminary work to be able to easily reference the serial lines
in Device Tree files. One expected use is when providing stdout-path
property for barebox.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/0683d1a823fe9b75849f3dafcf1cf6ee291cdca6.1416613429.git.arno@natisbad.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
As reported by Andrew, the vendor prefix for Seiko Instruments, Inc.
S-35390A I2C RTC chip in kirkwood-synology.dtsi has a typo (ssi
instead of sii). This patches fixes it.
Note: i2c devices ignore the optional vendor prefix, which explains
why it worked with the typo and also why there is no backward
compatibility issues with the fix.
Reported-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/0444140a267d982c3e5f5f2b7b5f2dc41d010e2a.1416613429.git.arno@natisbad.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Commit a095b1c78a ("ARM: mvebu: sort DT nodes by address")
missed placing the system-controller in the correct order.
Fixes: a095b1c78a ("ARM: mvebu: sort DT nodes by address")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/20141114204333.GS27002@pengutronix.de
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
In order to update MAC address entries in the ethernet nodes in Device Tree
both mainline U-Boot and Barebox bootloaders accept the same format of aliases,
which is 'ethernetX', where X stands for an interface number.
Other platforms in the mainline Linux, that comprise ethernet references in
'/aliases' node (like various flavours of imx or sunXi), follow the naming
scheme described above.
This commit ajusts ethernet aliases of Marvell Armada 38x SoC to be properly
recognized by bootloaders' MAC address fixup routines.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1415980652-7429-5-git-send-email-mw@semihalf.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
For proper operation of Armada 38x SDHCI controller proper 'clocks' property
is sufficient. Therefore it is not useful to keep an additional
'clock-frequency' property in SDHCI controller node of board-level Device Tree
file for Armada 385 DB.
This commit gets rid of useless 'clock-frequency' property.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1415980652-7429-4-git-send-email-mw@semihalf.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Marvell Armada 38x SoC's SDHCI interface is capable of using 1.8v voltage,
needed for driving "UHS-I" SD cards at their full speed. It is not, however,
possible on the DB board. Due to physical connectivity connector supply is tied
to 3v and any attempt of changing voltage in order to operate in the fastest UHS
modes fails.
This patch enables equivalent SDHCI quirk in order to adjust controller
operation to system capabilities.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1415980652-7429-3-git-send-email-mw@semihalf.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
