Upon encountering any error, few important registers are being captured
in trace logs in sdhci_dumpregs(). But without capturing exact error,
it would be tough to determine from which point in driver this dumpregs
has called. So capture the error state as well in Trace logs before
calling sdhci_dumpregs(). Also capture power irq related registers in
Trace logs upon any power irq related errors.
Change-Id: Ide172cdfb88a988cd4220bed03d05b8c6c4f15cb
Signed-off-by: Siba Prasad <sibap@codeaurora.org>
During hardware initialization charger is configured in
DRP mode from force UFP mode and after mode configuration
hardware takes ~300/400 msec for UFP/DFP detection. In case
if the delay between moving to DRP mode and software enabling
interrupts is more than hardware detection delay then software
will miss the detection interrupt. Fix this by moving DRP
configuration after interrupt request this ensures software will
receive interrupt once hardware detection completes.
CRs-Fixed: 2065296
Change-Id: I55c59ed558e8db40a7b1af7638832da1f9547222
Signed-off-by: Ashay Jaiswal <ashayj@codeaurora.org>
Change interface handler is not registered with mac80211.
The change interface handler is needed to run p2p go/cli
on the same interface as p2p control interface.
Add change interface handler for ath10k.
CRs-Fixed: 2063870
Change-Id: Ia06850a938b9d5e89d970792e3f0a776693a5f25
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
When we add an interface immediately after removing
the interface the vdev deletion in firmware might not
have been completed. We need to synchronize the vdev creation
with the firmware.
Wait for vdev delete response from firmware when we
remove an interface.
CRs-Fixed: 2065345
Change-Id: Id045087b03d5c5e6451f79b9c1177aca26ed34a2
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Some audio devices with two channels require the host
to issue SET_CUR command on the Volume control on
both the channels in order to function (playback or
record). Currently, the Linux Host driver issues SET_CUR
only for the 1st channel. Hence, add the quirk for
concerned devices for SET_CUR on 2nd channel.
Change-Id: I6f0bbcdfd3a8b3ccb33a1d56c252c701849a442f
Signed-off-by: Ajay Agarwal <ajaya@codeaurora.org>
The acquiring of wakelock prevents the system from entering
suspend for high frequency non-wakeup sensor requests. With
the change IPCRTR now does not acquire a wakelock while cpu
is out of suspend. This allows the cpu to enter suspend.
The wakelocks are enabled in the suspend path so that future
wakeup capable sensor events gets handled without issues.
The wakelocks are disabled post resume from suspend.
This change affects only the data on the SLPI edge.
Change-Id: Iae3dafb735bfb0d3000487f2fa2216d68e9a026f
Signed-off-by: Ramakrishnan Ganesh <ramakris@codeaurora.org>
Add support for a custom hotplug event that is triggered when the
status of the connector has changed. The event string of the
custom event will be in the following format:
"name=<connector name> status=<connector status>"
For example, when the DisplayPort connector has its status
updated to connected then the event string that is used as part
of the hotplug event will be as follows:
"name=DP-1 status=connected"
If the connector name is not known or is invalid at the time that
the event is triggered then the name will be reported as "unknown".
Change-Id: I5d6164d1e8e651cb05527733d68fa86fefb9e6ce
Signed-off-by: Tatenda Chipeperekwa <tatendac@codeaurora.org>
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
The kernel watchdog is a great debugging tool for finding tasks that
consume a disproportionate amount of CPU time in contiguous chunks. One
can imagine building a similar watchdog for arbitrary driver threads
using save_stack_trace_tsk() and print_stack_trace(). However, this is
not viable for dynamically loaded driver modules on ARM platforms
because save_stack_trace_tsk() is not exported for those architectures.
Export save_stack_trace_tsk() for the ARM64 architecture to align with
x86 and support various debugging use cases such as arbitrary driver
thread watchdog timers.
Change-Id: I61e9d2afc4703a786fa6dcaf82fe46c0ed250045
CRs-Fixed: 2061326
Signed-off-by: Dustin Brown <dustinb@codeaurora.org>
