Even if the management counters are configured to be 32 bit register
values, the [rt]xoctetcount_gb and [rt]xoctetcount_g counters are
always 64 bit counter registers. Since they are not being treated as
64 bit values, these statistics are being reported incorrectly (ifconfig,
ethtool, etc.).
Update the routines used to read the registers to access the "hi"
register (an offset of 4 from the "lo" register) to create a 64 bit
value for these 64 bit counters.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new fancy eth_get_headlen() to pull exactly the headers
into skb->head.
This speeds up GRE traffic (or more generally tunneled traffuc),
as GRO can aggregate up to 17 MSS per GRO packet instead of 8.
(Pulling too much data was forcing GRO to keep 2 frags per MSS)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSP_NEVER_DEFINED #ifdef is confusing, it slips in an
extra } which is not required because the previous code is
indented incorrectly. Correct the identation and remove the
extraneous DSP_NEVER_DEFINED
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does not affect the 10/100 GRETH MAC.
Before all GBit GRETH TX descriptor ring cleaning was done in
start_xmit(), when descriptor list became full it activated
TX interrupt to start the NAPI rx poll function to do TX ring
cleaning.
With this patch the TX descriptor ring is always cleaned from
the NAPI rx poll function, triggered via TX or RX interrupt.
Otherwise we could end up in TX frames being sent but not
reported to the stack being sent. On the 10/100 GRETH this
is not an issue since the SKB is copied&aligned into private
buffers so that the SKB can be freed directly on start_xmit()
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cnic module needs to ensure that if ipv6 support is compiled as a module,
then the cnic module cannot be compiled as built-in as it depends on ipv6.
Made this check cleaner via Kconfig
Use simpler IS_ENABLED for CONFIG_VLAN_8021Q check
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to HW errata the APM X-Gene AHCI SATA host controller reports link
down even if the device presence is detected. This issue is due to speed
negotiation failure. This patch implements the algorithm to retry the
COMRESET if PxSTAT register reports device presence detected but
PHY communication not established. The maximum retry attempts are 3.
This patch also fixes the code to match the algorithm for the printing
a warning message if the disparity error still exists after link up.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch implements the feature to skip the PHY and clock
initialization if it is already configured by the firmware.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Eric Dumazet says:
====================
tcp: deduplicate TCP_SKB_CB(skb)->when
TCP_SKB_CB(skb)->when has different meaning in output and input paths.
In output path, it contains a timestamp.
In input path, it contains an ISN, chosen by tcp_timewait_state_process()
Its usage in output path is obsolete after usec timestamping.
Lets simplify and clean this.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 740b0f1841 ("tcp: switch rtt estimations to usec resolution"),
we no longer need to maintain timestamps in two different fields.
TCP_SKB_CB(skb)->when can be removed, as same information sits in skb_mstamp.stamp_jiffies
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP_SKB_CB(skb)->when has different meaning in output and input paths.
In output path, it contains a timestamp.
In input path, it contains an ISN, chosen by tcp_timewait_state_process()
Lets add a different name to ease code comprehension.
Note that 'when' field will disappear in following patch,
as skb_mstamp already contains timestamp, the anonymous
union will promptly disappear as well.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck says:
====================
net: Drop get_headlen functions in favor of generic function
This series replaces the igb_get_headlen and ixgbe_get_headlen functions
with a generic function named eth_get_headlen.
I have done some performance testing on ixgbe with 258 byte frames since
the calls are only used on frames larger than 256 bytes and have seen no
significant difference in CPU utilization.
v2: renamed __skb_get_poff to skb_get_poff
renamed ___skb_get_poff to __skb_get_poff
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Update ixgbe to drop the ixgbe_get_headlen function in favor of eth_get_headlen.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update igb to drop the igb_get_headlen function in favor of eth_get_headlen.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates some of the flow_dissector api so that it can be used to
parse the length of ethernet buffers stored in fragments. Most of the
changes needed were to __skb_get_poff as it needed to be updated to support
sending a linear buffer instead of a skb.
I have split __skb_get_poff into two functions, the first is skb_get_poff
and it retains the functionality of the original __skb_get_poff. The other
function is __skb_get_poff which now works much like __skb_flow_dissect in
relation to skb_flow_dissect in that it provides the same functionality but
works with just a data buffer and hlen instead of needing an skb.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck says:
====================
This change makes it so that the core path for the phy timestamping logic
is shared between skb_tx_tstamp and skb_complete_tx_timestamp. In addition
it provides a means of using the same skb clone type path in non phy
timestamping drivers.
The main motivation for this is to enable non-phy drivers to be able to
manipulate tx timestamp skbs for such things as putting them in lists or
setting aside buffer in the context block.
v2: Incorporated suggested changes from Willem de Bruijn and Eric Dumazet
dropped uneeded comment
restored order of hwtstamp vs swtstamp
added destructor for skb
Dropped usage of skb_complete_tx_timestamp as a kfree_skb w/ destructor
v3: Updated destructor handling and dealt with socket reference counting issues
v4: Split out combining destructors into a separate patch
====================
Since sock_efree and sock_demux are essentially the same code for non-TCP
sockets and the case where CONFIG_INET is not defined we can combine the
code or replace the call to sock_edemux in several spots. As a result we
can avoid a bit of unnecessary code or code duplication.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy timestamping takes a different path than the regular timestamping
does in that it will create a clone first so that the packets needing to be
timestamped can be placed in a queue, or the context block could be used.
In order to support these use cases I am pulling the core of the code out
so it can be used in other drivers beyond just phy devices.
In addition I have added a destructor named sock_efree which is meant to
provide a simple way for dropping the reference to skb exceptions that
aren't part of either the receive or send windows for the socket, and I
have removed some duplication in spots where this destructor could be used
in place of sock_edemux.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change merges the shared bits that exist between skb_tx_tstamp and
skb_complete_tx_timestamp. By doing this we can avoid the two diverging as
there were already changes pushed into skb_tx_tstamp that hadn't made it
into the other function.
In addition this resolves issues with the fact that
skb_complete_tx_timestamp was included in linux/skbuff.h even though it was
only compiled in if phy timestamping was enabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lets make this hash function a bit secure, as ICMP attacks are still
in the wild.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix spelling typo found in DocBook/networking.xml.
It is because the neworking.xml is generated from comments
in the source, I have to fix typo in comments within the source.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A buffer is incorrectly zeroed to the length of the pointer. If
cfg_payload_len < sizeof(void *) this can overwrites unrelated memory.
The buffer contents are never read, so no need to zero.
Fixes: 8fe2f761ca ("net-timestamp: expand documentation")
Reported-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We try to call free_netvsc_device(net_device) when "net_device" is NULL.
It leads to an Oops.
Fixes: f90251c8a6 ('hyperv: Increase the buffer length for netvsc_channel_cb()')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When 1G SFP RJ45 module is detected, driver must reset the Tx laser
in order to prevent link issues. As part of change, the link_attr_sync
was relocated from vars to params.
Signed-off-by: Yaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Bolle reports that 'select NETFILTER_XT_NAT' from the IPV4 and IPV6
NAT tables becomes noop since there is no Kconfig switch for it. Add the
Kconfig switch to resolve this problem.
Fixes: 8993cf8 netfilter: move NAT Kconfig switches out of the iptables scope
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-09-04
This series contains updates to i40e, i40evf, ixgbe and ixgbevf.
Catherine adds dual speed module support to i40e. Updates i40e to allow
the user to change link settings when the link is down.
Serey renames i40e_ndo_set_vf_spoofck() to i40e_ndo_set_vf_spookchk()
to be more consistent with what is defined in netdev and removes a
unnecessary variable assignment.
Jesse makes a malicious driver detection warning only print if extended
driver string is enabled for i40e. Fixes a panic under traffic load when
resetting or if/whenever there was a Tx-timeout because we were enabling
the Tx queue to early.
Anjali fixes an issue when PF reset fails, where we were trying to restart
the admin queue which has not been setup at that point. This resolves an
occasional kernel panic when PF reset fails for some reason.
Ethan Zhao replaces the use of a local i40e_vfs_are_assigned() with the
global kernel pci_vfs_assigned() for i40e.
Alex cleans up the FDB handling for ixgbe. This change makes it so that
the behavior for FDB handling is consistent between both the SR-IOV and
non-SR-IOV cases. The main change is that we perform bounds checking on
the number of SR-IOV addresses regardless of if SR-IOV is enabled or not
as we can only support a certain number of addresses in the hardware.
Emil extends the pending Tx work check to the VF interfaces, where the
driver initiates a reset of the interface on link loss with pending Tx
work in order to clear the rings. Introduces a delay for 82599 VFs of
at least 500 usecs to make sure the VFLINKS value is correct, since this
bit tends to flap when a DA or SFP+ cable is disconnected.
Jacob adds code comments in ixgbe to make it more obvious that we are
resetting features based on the fact that we do not have MSI-X enabled,
and cannot use the previous settings. Also resolves a kernel NULL
pointer dereference by limiting the combined total of MACVLAN and
SR-IOV VFs, since the hardware has a limited number of pools available
(64). Previously, no checks were in place to limit the number of
accelerated MACVLAN devices based on the number of pools, which would
be ok since there was already a limit for these well below the number of
available pools. However, SR-IOV uses the very same pools, therefore
we need to ensure that the total number of pools does not exceed the
number of pools available in the hardware.
v2:
- clean up code comment in patch 5 by replacing "an" with "auto
negotiation" based on feedback from Sergei Shtylyov
- removed un-necessary parenthesis around function call in patch 8
based on feedback from Sergei Shtylyov
====================
Simplify the interrupt resource lookup code in cpsw_probe() by the
following:
* Only look at the first member of the resource. As the driver only
works for DT-enabled platforms anyway, a resource of type
IORESOURCE_IRQ will only contain one single entry
(res->start == res->end), so there is no need for the iteration.
* Add a bounds check to avoid overflows if we are passed more than
ARRAY_SIZE(priv->irqs_table) resources.
* Assign 'ret' with the return value of devm_request_irq() so that
cpsw_probe() returns the appropriate error code.
* If devm_request_irq() fails, report the error code in the log
message.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nh_exceptions is effectively used under rcu, but lacks proper
barriers. Between kzalloc() and setting of nh->nh_exceptions(),
we need a proper memory barrier.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 4895c771c7 ("ipv4: Add FIB nexthop exceptions.")
Signed-off-by: David S. Miller <davem@davemloft.net>
addrconf_get_prefix_route() ensures to get the right route in the right table.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason to take a refcnt before deleting the peer address route.
It's done some lines below for the local prefix route because
inet6_ifa_finish_destroy() will release it at the end.
For the peer address route, we want to free it right now.
This bug has been introduced by commit
caeaba7900 ("ipv6: add support of peer address").
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This syntax error was covered by L2TP_REFCNT_DEBUG not being set by
default.
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Lendacky says:
====================
amd-xgbe: AMD XGBE driver updates 2014-09-03
The following series of patches includes fixes/updates to the driver.
- Query the device for the actual speed mode (KR/KX) rather than trying
to track it
- Update parallel detection logic to support KR mode
- Fix new warnings from checkpatch in the amd-xgbe and amd-xgbe-phy
driver
This patch series is based on net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains fixes identified by checkpatch when run with the
strict option.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains fixes identified by checkpatch when run with the
strict option.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to allow parallel detection to work in KR speed. With
both speed modes of KX and KR supported, KX must be checked first.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since device resets can change the current mode it's possible to think
the device is in a different mode than it actually is. Rather than
trying to determine every place that is needed to set/save the current
mode, be safe and check the devices actual mode when needed rather than
trying to track it.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The timestamping API has separate bits for generating and reporting
timestamps. A software timestamp should only be reported for a packet
when the packet has the relevant generation flag (SKBTX_..) set
and the socket has reporting bit SOF_TIMESTAMPING_SOFTWARE set.
The second check was accidentally removed. Reinstitute the original
behavior.
Tested:
Without this patch, Documentation/networking/txtimestamp reports
timestamps regardless of whether SOF_TIMESTAMPING_SOFTWARE is set.
After the patch, it only reports them when the flag is set.
Fixes: f24b9be595 ("net-timestamp: extend SCM_TIMESTAMPING ancillary data struct")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
They are use less, and may generate compiling warnings, so remove them
(microblaze, arc, arm64, and unicore32 have already defined PCI_IOBASE).
The related warnings (with allmodconfig under microblaze):
CC [M] drivers/net/fddi/skfp/skfddi.o
In file included from drivers/net/fddi/skfp/skfddi.c:95:0:
drivers/net/fddi/skfp/h/skfbi.h:151:0: warning: "PCI_IOBASE" redefined
#define PCI_IOBASE 0xffffff00L /* Bit 31..8: I/O Base address */
^
In file included from include/linux/io.h:22:0,
from include/linux/pci.h:31,
from drivers/net/fddi/skfp/skfddi.c:82:
./arch/microblaze/include/asm/io.h:33:0: note: this is the location of the previous definition
#define PCI_IOBASE ((void __iomem *)_IO_BASE)
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull i2c bugfixes from Wolfram Sang:
"I2C driver bugfixes for the 3.17 release. Details can be found in the
commit messages, yet I think this is typical driver stuff"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
Revert "i2c: rcar: remove spinlock"
i2c: at91: add bound checking on SMBus block length bytes
i2c: rk3x: fix bug that cause transfer fails in master receive mode
i2c: at91: Fix a race condition during signal handling in at91_do_twi_xfer.
i2c: mv64xxx: continue probe when clock-frequency is missing
i2c: rcar: fix MNR interrupt handling
The function cleaning up an initialized event
was called from the "event_del" handler, instead
of being used as the "destroy" callback. In case of
events group allocation this caused NULL pointer
dereference (as events are added and deleted
multiple times then). Fixed now.
Signed-off-by: Pawel Moll <mail@pawelmoll.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Hayes Wang says:
====================
r8152: random MAC address
If the interface has invalid MAC address, it couldn't
be used. In order to let it work normally, give a
random one.
v3:
Remove
ether_addr_copy(dev->perm_addr, dev->dev_addr);
v2:
Use "%pM" format specifier for printing a MAC address.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If the hw doesn't have a valid MAC address, give a random one and
set it to the hw.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Exchange the location of rtl8152_set_mac_address() and
set_ethernet_addr(). Then, the set_ethernet_addr() could
set the MAC address by calling rtl8152_set_mac_address()
later.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Govindarajulu Varadarajan says:
====================
enic: Add support for rx_copybreak
The following series implements rx_copybreak.
dma_map_single()/dma_unmap_single() is more expensive than alloc_skb & memcpy
for smaller packets. By doing this we can reuse the dma buff which is already
mapped. This is very useful when iommu is on. The default skb copybreak value
is 256.
When iommu is on, we can go much higher than 256. All the drivers that supports
rx_copybreak provides module parameter to change this value. Since module
parameter is the least preferred way for changing driver values, this series
adds ethtool support for setting rx_copybreak.
v4:
Validate tunable length in ethtool_get_tunable, not in driver implemented
function.
Loose tunable_ops array for each tunable type. Define one function and let the
driver use switch case for each type.
Use double underscore for data type in UAPI headers.
Use const qualifier where possible.
v3:
Add tunable namespace to ethtool. Use new ethtool cmd ETHTOOL_S/GTUNABLE to
set/get rx_copybreak from userspace.
v2:
Add new ethtool_cmd for DMA buffer parameters, instead of adding new members to
existing ethtool_ringparam.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for setting/getting rx_copybreak using
generic ethtool tunable.
Defines enic_get_tunable() & enic_set_tunable() to get/set rx_copybreak.
As of now, these two function supports only rx_copybreak.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds new ethtool cmd, ETHTOOL_GTUNABLE & ETHTOOL_STUNABLE for getting
tunable values from driver.
Add get_tunable and set_tunable to ethtool_ops. Driver implements these
functions for getting/setting tunable value.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling dma_map_single()/dma_unmap_single() is quite expensive compared
to copying a small packet. So let's copy short frames and keep the buffers
mapped.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
