VFLINKS.LINKUP bit tends to flap when a DA or SFP+ cable is disconnected.
It can take up to 500 usecs for the LINKUP bit to be correct.
This patch resolves the issue by introducing a delay for 82599 VFs of at
least 500 usecs to make sure the VFLINKS value is correct.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ixgbe initiates a reset of the interface on link loss with pending Tx work
in order to clear the rings.
This patch extends the pending Tx work check to the VF interfaces with the
same purpose.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that the behavior for FDB handling is consistent
between both the SR-IOV and non-SR-IOV cases. The main change here is that we
perform bounds checking on the number of SR-IOV addresses regardless of if
SR-IOV is enabled or not as we can only support a certain number of addresses
in the hardware.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is global funcion pci_vfs_assigned(), so use it instead of composing
local one.
Signed-off-by: Ethan Zhao <ethan.kernel@gmail.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e version to 1.0.11 and i40evf version to 1.0.5.
Change-ID: I63a60fa2efe82aae87a8a3095f43218db57d46ce
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
This fixes the panic under traffic load when resetting. This issue
could also show up if/whenever there is a Tx-timeout.
Change-ID: Ie393a1f17fd5d962e56fc3bfe784899ef25402f5
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We shouldn't restart Admin queue subtask if PF reset fails since we do
not have the AQ setup at that point. This patch makes sure we disable AQ
clean subtask when PF reset fails.
This will resolve an occasional kernel panic when PF reset fails for
some reason.
Change-ID: I11a747773362a8c5c0ad7a10cd34be0bda8eb9e8
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver is un-necessarily printing a warning that is only marginally
useful to the user. Make the warning only print if extended driver
string printing is enabled, other messages related to a reset event
will still continue to print.
Change-ID: I5e8beca6516a2f176cd2e72b0ac2b3b909e6c953
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we don't seem to be getting an LSE telling us link is going down
during set_phy_config (but we do get an LSE telling us we are coming
back up), fake one for the OS and tell them link is going down. Also
do an atomic restart no matter what because there are times the user
may want to end with link up even if they started with link down (like
if they accidentally set it to a speed that can't link and are trying to
fix it).
Change-ID: I0a642af9c1d0feb67bce741aba1a9c33bd349ed6
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove unnecessary setting of "ret" variable as it's already set at
the top of the function.
Change-ID: Icaccfc67f335817a23579b7c43625d59ad6c9925
Signed-off-by: Serey Kong <serey.kong@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change "spoofck" to "spoofchk" to be consistent with as defined in netdev.
Change-ID: I9866d6284cb5f92c8d71dc0776c6d1e71dfb62a5
Signed-off-by: Serey Kong <serey.kong@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allow the user to change auto-negotiation and speed settings if
link is down.
Change-ID: I372967c627682b5e1835f623a7cbf41b21b51043
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that fw has implemented dual speed module support, we can add ours.
Also, add the phy type for 1G LR/SR and set its media type to fiber.
Lastly, instead of a WARN_ON if the phy type is not recognized just print
a warning.
Change-ID: I2e5227d4a8c2907b0ed423038e5dbce774e466b0
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It would appear the mlx4_en driver was still making a call to
dev_kfree_skb_any() where dev_consume_skb_any() would be more
appropriate. This should make dropped packet profiling/tracking
easier/better over a NIC driven by mlx4_en.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although rhashtable library allows user to specify a quiet big size
for user's created hash table, the table may be shrunk to a
very small size - HASH_MIN_SIZE(4) after object is removed from
the table at the first time. Subsequently, even if the total amount
of objects saved in the table is quite lower than user's initial
setting in a long time, the hash table size is still dynamically
adjusted by rhashtable_shrink() or rhashtable_expand() each time
object is inserted or removed from the table. However, as
synchronize_rcu() has to be called when table is shrunk or
expanded by the two functions, we should permit user to set the
minimum table size through configuring the minimum number of shifts
according to user specific requirement, avoiding these expensive
actions of shrinking or expanding because of calling synchronize_rcu().
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
distinguish between the dropped and consumed skb, not assume the skb
is consumed always
Cc: Thomas Graf <tgraf@noironetworks.com>
Cc: Pravin Shelar <pshelar@nicira.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 50cbe9ab5f ("net: Validate xmit SKBs right when we
pull them out of the qdisc") the validation code was moved out of
dev_hard_start_xmit and into dequeue_skb.
However this overlooked the fact that we do not always enqueue
the skb onto a qdisc. First situation is if qdisc have flag
TCQ_F_CAN_BYPASS and qdisc is empty. Second situation is if
there is no qdisc on the device, which is a common case for
software devices.
Originally spotted and inital patch by Alexander Duyck.
As a result Alex was seeing issues trying to connect to a
vhost_net interface after commit 50cbe9ab5f was applied.
Added a call to validate_xmit_skb() in __dev_xmit_skb(), in the
code path for qdiscs with TCQ_F_CAN_BYPASS flag, and in
__dev_queue_xmit() when no qdisc.
Also handle the error situation where dev_hard_start_xmit() could
return a skb list, and does not return dev_xmit_complete(rc) and
falls through to the kfree_skb(), in that situation it should
call kfree_skb_list().
Fixes: 50cbe9ab5f ("net: Validate xmit SKBs right when we pull them out of the qdisc")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
More minor fixes to merge commit 53fda7f7f9 (Merge branch 'xmit_list')
that allows us to work with a list of SKBs.
Fixing exit cases in qdisc_reset() and qdisc_destroy(), where a
leftover requeued SKB (qdisc->gso_skb) can have the potential of
being a skb list, thus use kfree_skb_list().
This is a followup to commit 10770bc2d1 ("qdisc: adjustments for
API allowing skb list xmits").
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
here's a couple of display regression fixes for 3.17.
* tag 'drm-intel-fixes-2014-09-03' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Fix lock dropping in intel_tv_detect()
drm/i915: handle G45/GM45 pulse detection connected state.
Pull input subsystem updates from Dmitry Torokhov:
"A fix for MT breakage, enhancement to Elantech PS/2 driver and a
couple of assorted fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elantech - add support for trackpoint found on some v3 models
Input: elantech - reset the device when elantech probe fails
Input: ALPS - suppress message about 'Unknown touchpad'
Input: fix used slots detection breakage
Input: sparc - i8042-sparcio.h: fix unused kbd_res warning
Input: atmel_mxt_ts - improve description of gpio-keymap property
Several bug fixes for issues that have been lurking for a while:
- Check that devices haven't set the flag saying they only support
register at a time operation while we're doing cache syncs, otherwise
we fail to restore caches.
- Ensure that we don't mark all registers on devices using format_write()
as cacheable, avoiding adding a cache of things like reset registers
which we don't want to rewrite during cache sync.
- Make sure we create the debugfs files in the correct directory.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Eo/I
-----END PGP SIGNATURE-----
Merge tag 'regmap-v3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"Several bug fixes for issues that have been lurking for a while:
- Check that devices haven't set the flag saying they only support
register at a time operation while we're doing cache syncs,
otherwise we fail to restore caches
- Ensure that we don't mark all registers on devices using
format_write() as cacheable, avoiding adding a cache of things like
reset registers which we don't want to rewrite during cache sync
- Make sure we create the debugfs files in the correct directory"
* tag 'regmap-v3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Don't attempt block writes when syncing cache on single_rw devices
regmap: Fix handling of volatile registers for format_write() chips
regmap: Fix regcache debugfs initialization
On the GP EVM, the ambient light sensor is limited to 100KHz on the
I2C bus.
So use 100kHz for I2C on the GP EVM due to this limitation on the
ambient light sensor.
Reported-by: Aparna Balasubramanian <aparnab@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The 8th NAND partition should be named "NAND.u-boot-env.backup1"
instead of "NAND.u-boot-env". This is to be consistent with other
TI boards as well as u-boot.
CC: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The I2C3 pins are taken from pads E21 (GPIO6_14) and
F20 (GPIO6_15). Use the right pinmux register and mode.
Also set the I2C3 bus frequency to a safer 400KHz than
3.4Mhz.
CC: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is a following AB-BA dependency between cpu_hotplug.lock and
cpuidle_lock:
1) cpu_hotplug.lock -> cpuidle_lock
enable_nonboot_cpus()
_cpu_up()
cpu_hotplug_begin()
LOCK(cpu_hotplug.lock)
cpu_notify()
...
acpi_processor_hotplug()
cpuidle_pause_and_lock()
LOCK(cpuidle_lock)
2) cpuidle_lock -> cpu_hotplug.lock
acpi_os_execute_deferred() workqueue
...
acpi_processor_cst_has_changed()
cpuidle_pause_and_lock()
LOCK(cpuidle_lock)
get_online_cpus()
LOCK(cpu_hotplug.lock)
Fix this by reversing the order acpi_processor_cst_has_changed() does
thigs -- let it first execute the protection against CPU hotplug by
calling get_online_cpus() and obtain the cpuidle lock only after that (and
perform the symmentric change when allowing CPUs hotplug again and
dropping cpuidle lock).
Spotted by lockdep.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The _SUN device indentification object is not guaranteed to return
the same value every time it is executed, so we should not cache its
return value, but rather execute it every time as needed. If it is
cached, an incorrect stale value may be used in some situations.
This issue was exposed by commit 202317a573 (ACPI / scan: Add
acpi_device objects for all device nodes in the namespace). Fix it
by avoiding to cache the return value of _SUN.
Fixes: 202317a573 (ACPI / scan: Add acpi_device objects for all device nodes in the namespace)
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: 3.14+ <stable@vger.kernel.org> # 3.14+
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The auxiliary station is being handled using the internal
station helper functions, clean that up and make the helpers
static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Unify all the functions that handle the per-interface broadcast
station and make them have mvm and vif parameters. While at it,
add a new function to allocate the broadcast station instead of
open-coding it, and make the combined alloc+send and free+send
functions use the alloc/free & send functions.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There are a few places that can call the function
iwl_mvm_mac_get_queues_mask() instead of open-coding the
equivalent, so do that. This requires changing it to return
the multicast queue as part of the bitmap, which broke GO
mode because including it in the broadcast station queues
seems to confuse the firmware, so work around that.
Also, the API defines that the CAB queue shouldn't be
included in the TFD queue mask, adjust the comment
accordingly (not a bug).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Instead of checking whether a given station is the first to
be added on a client interface check for the new TDLS flag
and warn in the unexpected cases.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The queue handling is a bit unclear - we have an array for
stop_count[IWL_MAX_HW_QUEUES] but indices really are the
mac80211 queue numbers. Change the array to be only of the
right size for mac80211 queues (IEEE80211_MAX_QUEUES) and
rename it to be clearer.
While at it, also remove the unused transport queue stop
bitmap in mvm.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Move all FIFO definitions together into the firmware API
header file and use the same enum/naming scheme for the
command FIFO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The firmware would like to have a MAC context (unassoc)
before the AP station is removed (we do this) but would
like to keep the BSSID until after it is removed, so we
need to send two commands - one with the BSSID before
and one without the BSSID after.
In order to do this, we need to store the BSSID as it
will have been cleared by mac80211 by the time we get
notified of the disassociation. Also pass it around as
an override to the various functions needing it, and
keep taking it from the mac80211 data otherwise. This
avoids having to keep track of the BSSID in all modes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
During a channel switch we should tell the firmware to disable TX
temporarily and re-enable it after the switch is done.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Our legal structure changed at some point (see wikipedia), but
we forgot to immediately switch over to the new copyright
notice.
For files that we have modified in the time since the change,
add the proper copyright notice now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently the firmware is handling this, but that is wrong as it then
needs to assume a certain command queue, therefore this should be in
the driver; add it here so it can be removed from the firmware in the
future.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently a valid sta_id is assumed to mean that the queue is
meant to also be aggregated, but that assumption will not be
true in the future, so don't make it in the lower level but
only in the inline wrapper.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In a later patch, the hardware configuration will be moved to
firmware. Prepare for this by allowing hardware configuration
in the transport to be skipped by not passing a configuration
on enable and passing configure_scd=false on disable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The tracepoints that are only used in code linked with iwlwifi.ko,
as are the tracepoints, don't need to be exported, so don't.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In order to follow more easily what's going on, add some
debug statements to the quota allocation algorithm.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Enable fragmented scan that was diabled due to a FW bug.
New fixed FWs use a TLV bit to advertise fragmented scan support.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Instead of having all arguments passed to the function,
add a struct to hold them and only pass some directly.
This will make future work in this area cleaner.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Configuring the hw scheduler during queue enablement is done by
writing the appropriate values to the scheduler peripherals, and
it is essentially the same for all buses.
Whenever writing is done via the standard iwl_write_prph, we can
avoid duplicating the code for each bus. Those operations are
queue deactivation, RA/TID mapping, chain-building settings,
enabling/disabling aggregations and activating/deactivating the
TX FIFOs.
Consolidate this code using static inlines in a new header file.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Make sure that when running the TDLS discovery session
protection - the time event that ensures we remain on channel
has been scheduled and started running before leaving.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We need to disable PS when a monitor vif is active or, in the future,
when a channel switch is happening. Add a boolean to mvmvif that
allows PS to be disabled generically. Additionally, make the monitor
interface use this new flag when it gets activated.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add a new iwl_mvm_power_update_ps() function that allows only ps to be
updated according to changes in the vifs. This allows us to disable
ps only without affecting the pm values of the vifs (and to avoid
sending unnecessary MAC_PM_POWER_TABLE commands to the firmware).
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Separate the ps part of iwl_mvm_power_set_pm() into a new
iwl_mvm_power_set_ps() function. This will enable us to update the ps
part independently from the rest, which is needed by CSA (at least).
This required a bit of refactoring and the creation of a new iterator
function.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
