Add support for new QMI IDL in IPA driver for new message
QMI_IPA_INSTALL_FILTER_RULE_EX_REQ_V01 which allows to send
at most 128 rules.
Change-Id: I886e40f597169939ce4598863fd80145743d8db7
Signed-off-by: Skylar Chang <chiaweic@codeaurora.org>
It is recommended to use NUM_OF_TRB greater than USB controller's
TRB cache size. Currently USB controller's TRB cache size on GSI
available platform is 12. TRB ring base address must be aligned to
TRB ring length rounded to power of two. Hence set NUM_OF_TRB as
15 for both IN and OUT GSI endpoints.
CRs-Fixed: 1067833
Change-Id: Iab8b0bc6fd17183fc6056f06a90421cde24987c8
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
During recovery, if another PD down notification received because
of crash then handle the case. If debug enabled then BUG_ON to
debug the second crash.
CRs-fixed: 1067873
Change-Id: I6e8e92ca0ee11830f933e198fea502c915d36e59
Signed-off-by: Prashanth Bhatta <bhattap@codeaurora.org>
During recovery, if not able to force enable hardware clocks then
do top level reset only.
CRs-fixed: 1067868
Change-Id: Ie23ca022c94cd214a9e415e9fb774055cfaf881d
Signed-off-by: Prashanth Bhatta <bhattap@codeaurora.org>
Remove panic on single bit cache error because single bit error
can be corrected.
Change-Id: Id14ffa45a1326e47adc847c012e9ac21c6954990
Signed-off-by: Runmin Wang <runminw@codeaurora.org>
Remove warn_on message since the required CPUMERRSR and L2MERRSR
info is already printed in the dmesg.
Change-Id: I2e93bcd1e84d43bc7a58af0be02d5337d936d4ee
Signed-off-by: Runmin Wang <runminw@codeaurora.org>
tx_iface_clk and rx_iface_clk does not exist in newer version
of ufs-phy HW, hence remove the missing clk warnings for them.
Change-Id: Ic8dd3e9521159ce8da064da38cfa12e75f07209f
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
It is possible a variable will be accessed before
it is ever initialized. Properly initialize this
variable when it is declared.
Change-Id: Id1523786f1c87449ed3943f1726766dad6a4ade2
Signed-off-by: Tony Truong <truong@codeaurora.org>
As part of the PHY shut down sequence, current driver
disable the phy pmic regulators. This is not the
expected sequence, so make sure the pmic phy
regulators stay enabled.
Change-Id: Ia65a71347666ed9fa3f6bf92fe7c573638301254
Signed-off-by: Ingrid Gallardo <ingridg@codeaurora.org>
Extend sensor_info structure with one more field to be able to export
the IR CUT device to mm-qcamera-daemon.
Change-Id: I63da161f90bce2c33d1e7e9d5822c8635e307fd5
Signed-off-by: Vivek Veenam <vveenam@codeaurora.org>
This driver is able to control a IR CUT device. The interface to
user space is:
CFG_IR_CUT_INIT
CFG_IR_CUT_OFF
CFG_IR_CUT_ON
CFG_IR_CUT_RELEASE
Change-Id: I30d1c4e6c40b8e58a70f06db9e05231b4c7f676f
Signed-off-by: Vivek Veenam <vveenam@codeaurora.org>
During graceful shutdown we await acknowledgment before executing
reset sequence for subsystem, adding check to evaluate if subsys is
crashed in between so that we dont spend time for hopeless ack wait.
Change-Id: I34bba1ebc417a3d6daa3b6e0a38c4b519c82c606
Signed-off-by: Avaneesh Kumar Dwivedi <akdwived@codeaurora.org>
Remove support for 710Mhz for A540v2 GPU because it is not supported.
CRs-Fixed: 1056661
Change-Id: Ida0d2d010f7bd226d7e2221f63e64a1d7e5a9075
Signed-off-by: Oleg Perelet <operelet@codeaurora.org>
During an timeout event in the SDE rotator driver, a spinlock with IRQ
is disabled in order to capture the rotator hw status registers. If
during this time performs an evtlog timeout logging, a mutex_lock
within the logging sequence will cause a panic. We must and only should
perform the evtlog timeout logging after the spinlock is released.
CRs-Fixed: 1067811
Change-Id: I56b7e5713069ad8ac8d5ae43a492a0ab0f4e82ff
Signed-off-by: Benjamin Chan <bkchan@codeaurora.org>
First cut of NOIRQ driver used a sequence of
trigger commands (PAUSE, STOP, RESUME) to handle
device switch. This led to a state transition issue
where after resume trigger, the state of the stream
would change to OPEN instead of RUNNING. To fix
this, clients are expected to do RESET ioctl instead.
RESET ioctl does not change the state of the stream.
Bug: 30615611
CRs-Fixed: 1051762
Change-Id: Ife6146d28c8bc834a79e861959eca03e58e12d5e
Signed-off-by: Haynes Mathew George <hgeorge@codeaurora.org>
On msmcobalt reference platform, earpiece path is not connected
to receiver, instead speaker path is used as receiver. So handset
AANC(Adaptive Active Noise cancellation) needs to be supported
on speaker path. Change enables ANC support on speaker path.
Change-Id: I8104994adc30810085cce73662f5abd5e15106ad
Signed-off-by: Sudheer Papothi <spapothi@codeaurora.org>
Signed-off-by: Vidyakumar Athota <vathota@codeaurora.org>
In msmcobalt platform, speaker path is used for handset mode also.
Add the mixer control to change gain in handset mode.
Change-Id: Ia291f7449cd04a855102a03324f7cdcb6f13dad0
Signed-off-by: Vidyakumar Athota <vathota@codeaurora.org>
Dynamic detection between wcd9335 and wcd934x codecs is supported on
msmcobalt. Probe sequence of the two codec drivers can occur in any
order. MCLK initialization is common for the two codecs which gets
called twice. Avoid wcd934x codec's probe sequence from resetting
wcd9335 codec's native mclk pinctrl if the pinctrl is already
initialized.
CRs-Fixed: 1066167
Change-Id: Idf65e15e08bb856d65b992b996cffa6ef2e6f974
Signed-off-by: Meng Wang <mwang@codeaurora.org>
According to vendor's suggestion, reset pin and interrupt pin must be
pulled down before touchpanel controller power up. This is required
for all Goodix devices.
Change-Id: If16fab02967abbd0c2a6e4365fed76f9e8729bc2
Signed-off-by: Bingzhe Cai <bingzhec@codeaurora.org>
Use macros instead of magic numbers for maximum i2c retries in
Goodix driver.
Change-Id: I9f7da9f43418cd1d423aaf331f41d37d13f248d4
Signed-off-by: Shantanu Jain <shjain@codeaurora.org>
Update the DMIC CLK and DATA registers to use the correct
settings required for DMIC High-Z on wcd934x. Registers
should be set to 0x6 for Slimbus mode and 0xD for I2C mode.
CRs-Fixed: 1059712
Change-Id: Ibe8ca2e40ee56708e8c84c174d12ce5841e6b1ce
Signed-off-by: Meng Wang <mwang@codeaurora.org>
This reverts commit <fae741edccb> ("usb: gsi: Queue control
notification on gsi_resume") as expected notification is not
queued resulting into mismatch of QMI transaction packet.
CRs-Fixed: 1067006
Change-Id: I4abdd79699d47054e268978aae9199f1d5d1ddcb
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
TMC abort needs to save TMC registers so that TMC data can be extracted
from device crash dumps.
Change-Id: I4339e84dc62e589e0f4d341e8143b1cd94a9cbe2
Signed-off-by: Shashank Mittal <mittals@codeaurora.org>
On client pushing message, allocate memory for event
data and copy before pushing to clients. This is to
avoid crash if client goes away before freeing the
memory.
Change-Id: Icff40d68d9b60617e8e3eb006eb697194b4e61f6
CRs-Fixed: 1065499
Signed-off-by: Sunil Paidimarri <hisunil@codeaurora.org>
