The parsing logic wrongly assumes the position of the initial/active power
level value in the gpu dts file. This leads to the active power level
always defaulting to a value of 1. Look for the initial power level
one level up in the device tree.
Change-Id: I63f8c8efd05ad3693c6f399f58bed44ac84105d2
Signed-off-by: Sharat Masetty <smasetty@codeaurora.org>
Automotive use case requirement is to have HDMI display as non-pluggable.
This change also set a custom mode as 1920x1080p@60Hz.
Change-Id: Ic2baec180d51dc6a91eaf72c44df1da066f04d2e
Signed-off-by: Rahul Sharma <sharah@codeaurora.org>
Update the arp and ns tuple for arp-ns tlv cmd and pass
the size of IP address and wlan net dev name during mem
copy and comparison.
CRs-Fixed: 2149966
Change-Id: I9457af4578c70f876c3a58e3d8c655dcaa476e07
Signed-off-by: Sarada Prasanna Garnayak <sgarna@codeaurora.org>
Add device pointer in all export symbol to
add support for numerous WLAN module.
CRs-Fixed: 2138446
Change-Id: I981155c165e4e5c2794b778afe647f8a588dd860
Signed-off-by: Sarada Prasanna Garnayak <sgarna@codeaurora.org>
If same event is unsubscribed before v4l2_event_subscribe returned,
Then function v4l2_event_subscribe have possibility use-after-free.
Serialize msm_subscribe_event and msm_unsubscribe_event to
prevent parallel invocation of v4l2_event_subscribe and
v4l2_event_unsubscribe.
Change-Id: Ia28cfb9d46550d58221f157337a1468f524753e3
Signed-off-by: Trishansh Bhardwaj <tbhardwa@codeaurora.org>
This is a fix for dynamic memory leak seen with incorrectly
allocating memory of a different size than with intended
size.
Change-Id: I821442ee6728ea90ceab7644e194f4e06369333a
Acked-by: Jyothi Jayanthi <jyothij@qti.qualcomm.com>
Signed-off-by: Michael Adisumarta <madisuma@codeaurora.org>
For non-pluggable display, it should not enable HPD. Instead, the
bridge should handle all the clocks for HDMI. Also the scrambler
should be activated after the HDMI has power on the clock.
Change-Id: I9162a49b8f314de4d30b0d82c7867a639ddf05a6
Signed-off-by: Camus Wong <camusw@codeaurora.org>
Compile ADV7481 as a module, as part of kernel modularization
requirement.
Change-Id: Ie3e9669d05646503de6ddd3468cbd6da4ee4eae4
Suggested-by: Resmi Rajendran <resmir@qti.qualcomm.com>
Signed-off-by: Rahul Sharma <sharah@codeaurora.org>
Remove "qcom,mdss-dsi-on-command" and "mdss-dsi-off command"
commands for boot up performance optimization.
The two commands are for native DSI panels without a bridge
chip. However,AUTO platform has adv7533 bridge chip,which
is controlled by I2C instead of the above two commands.
In addition,the two command will cause extra wait for about
210ms in dsi_panel_tx_cmd_set() for dsi_display_enbale().
This make drmAtomicCommit() in libdrm a little slower,
so total boot time will be longer.
Change-Id: I848d189d4055b5626eadd809fc5da7c9c4ecbcce
Signed-off-by: Daocai <daocai@codeaurora.org>
In current HDMI driver, SVDs and DTDs derived from EDID
of a DS HDMI sink are checked for supportness based
on previous connection's max TMDS clock.
Always reset the max TMDS clock supported by source
before reading EDID from DS HDMI device.
Change-Id: If5f58562f186634b1ed066fdebfc9fa6b55c6e8a
Signed-off-by: Narender Ankam <nankam@codeaurora.org>
Hypervisor supports psci-1.0 not 0.1 and new function IDs
have been defined in psci driver.
Change-Id: Id257dd264f9ffc812879997c0b227e53f84c86a2
Signed-off-by: Yimin Peng <yiminp@codeaurora.org>
In the cmdq request issuing path, cq driver invokes ICE driver calls
to get the configuration for encrypting/decrypting the data requests.
The ice driver in-turn makes calls to secure world (TZ) which can
process only single task at a time. If TZ is busy in servicing
something else when ICE driver invokes it, ICE driver would return
-EBUSY to cmdq driver.
The requests which failed due to ice error are neither issued to h/w
nor errored out, so resulting in filesystem corruptions.
We must re-queue the requests which failed with -EBUSY error, so that
it will be re-issued again as very next request.
Change-Id: I4557a5c3aca8dd53740e48e516e6011787df50d8
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
During patch download of devices, size validations & zero alloc
the buffers to ensure values passed are in range
CRs-fixed: 2084692
Change-Id: Ie1cd76fe68766d6d12d7262202e48c18ebe42274
Signed-off-by: Balvinder Singh <bpsingh@codeaurora.org>
command-queue request may fail during preparation/issuing in some
cases. In case if it fails, the error code needs to be propagated back
to the function which initiated the request so that the request can be
handled appropriately.
Change-Id: Ia6946c14f0c106fb30bd70ca5c9e600c516fdf55
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
