Driver is dynamically allocating memory based on bNumInterface from
device configuration descriptor and stores interface context
information using bInterfaceNum. Device can advertise
bInterfaceNum >= bNumInterface which results into out of bound memory
access. Hence create a mapping between interface context index and
interface number. Use this mapping to find unused context index or
load the context information of an interface.
Change-Id: Ic99b10abe662088c2c030526135689f7c78c595a
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
LMH DCVS driver doesn't change the low threshold from HLOS. When there is
new request to lower the high threshold, the low threshold will be
modified if the new high threshold is lower than the existing low
threshold. But the low threshold is not increased when the high
threshold is moved back again.
Update the LMH DCVSh driver to always update the low threshold value
when there is a new high threshold request. The new low threshold will
be 0.5C less than the high threshold.
Change-Id: I356e47de585ae81bd27859f790f673b31ae5ba72
Signed-off-by: Ram Chandrasekar <rkumbako@codeaurora.org>
Add battery voltage, current and low SoC thresholds for sdm660.
The BCL module will mitigate the CPU's, when battery reaches
the low voltage threshold, high current threshold or low
state of Charge.
Change-Id: Ie6cf0498bd7ad869640efc602d2573b6def7d5b7
Signed-off-by: Manaf Meethalavalappu Pallikunhi <manafm@codeaurora.org>
Enable BIMC GFX clock when A512 GPU is ready to access data
from DDR on SDM660.
Change-Id: Ib76ef7a4fd5362f8cb972f1e4e070157a59c2c27
Signed-off-by: Rajesh Kemisetti <rajeshk@codeaurora.org>
Configure the size of the default CMA region to 32 MB in
DT for sdm660.
Configuring the default CMA region in the DT is cleaner
than using CONFIG_CMA_SIZE_MBYTES since it is easier to
configure per target and the alloc ranges can be specified
in DT.
Change-Id: I64d4e1ee379b2a3110ecd403e7ed838948df6ca3
Signed-off-by: Shiraz Hashim <shashim@codeaurora.org>
Add camera node, include rear aux and front camera, also
include corresponding eeprom actuator ois flash and torch node.
Change-Id: I45d5e45ea82bafa78ef83638f1b374e03bb43145
Signed-off-by: Pengfei Liu <pengfeiliu@codeaurora.org>
Speed is not notified in case of platforms having micro USB connector
instead of USB type C connector. In this case, set speed as High speed
only as by default only high speed is supported over micro USB ports.
Change-Id: I6f29914ca9e2345157330651464b7a0c151f1f97
Signed-off-by: Vijayavardhan Vennapusa <vvreddy@codeaurora.org>
Enable IPA in SDM660.
IPA shunt data between apps, modem and USB.
Change-Id: I09aa16138d643b17b793162ca0591c143ad8da1f
Acked-by: Mohammed Javid <mjavid@qti.qualcomm.com>
Signed-off-by: Utkarsh Saxena <usaxena@codeaurora.org>
Select which SPSS firmware to load based on 2 fuses.
Change-Id: I7080cc0b58c38965ed7e58808431cf487008de9e
Signed-off-by: Amir Samuelov <amirs@codeaurora.org>
Use the proper clock for CSIPHY2 for SDM660.
CRs-Fixed: 1111640
Change-Id: If9eaa19a0ee837dbbe335597259a62287a1620d5
Signed-off-by: Shankar Ravi <rshankar@codeaurora.org>
