Venice2 uses the MAX98090 audio CODEC, and supports built-in speakers,
and a combo headphones/microphone jack. Add a top-level sound card node
to represent this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tegra124 contains a similar set of audio devices to previous Tegra chips.
Specifically, there is an AHUB device which contains DMA FIFOs and audio
routing, and which hosts various audio-related components such as I2S
controllers.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Enable all the I2C controllers that are wired up on Venice2. I don't
know the correct I2C bus clock rates, so set them all to a conservative
100KHz for now.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tegra124 has 6 I2C controllers. The first 5 have identical configuration
to Tegra114, but the sixth obviously has different interrupt/... IDs.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tegra124 has 4 MMC controllers just like previous versions of the SoC.
Note that there are some non-backwards-compatible HW differences, and
hence a new DT compatible value must be used to describe the HW.
Also enable the relevant controllers in the Venice2 board DT.
power-gpios property suggested by Thierry Reding.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Instantiate the APB DMA controller in the Tegra124 DT, and add all
DMA-related properties to other DT nodes that rely on (reference) the
DMA controller's node.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
The DT bindings now require module resets to be specified. The earlier
patches which added these nodes were originally written before that
requirement.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
This patch adds clock properties for devices in the DT for basic support
of Tegra124 SoC.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
[swarren, added missing unit address to "clock" node]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
For Tegra DT files, I've been attempting to keep the nodes sorted in
the order:
1) Nodes with reg, in order of reg.
2) Nodes without reg, alphabetically.
This patch fixes a few escapees that I missed:-(
The diffs look larger than they really are, because sometimes when one
node was moved up or down, diff chose to represent this as many other
nodes being moved the other way!
Signed-off-by: Stephen Warren <swarren@nvidia.com>
DT node names should include a unit address iff the node has a reg
property. For Tegra DTs at least, we were previously applying a different
rule, namely that node names only needed to include a unit address if it
was required to make the node name unique. Consequently, many unit
addresses are missing. Add them.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The A13-OLinuXino-MICRO is a small dev-board with the Allwinner A13 SoC:
https://www.olimex.com/Products/OLinuXino/A13/A13-OLinuXino-MICRO/
Features:
A13 Cortex A8 processor at 1GHz, 3D Mali400 GPU
256 MB RAM (128Mbit x 16)
5VDC input power supply with own ICs, noise immune design
1 USB host
1 USB OTG which can power the board
SD-card connector for booting the Linux image
VGA video output
LCD signals available on connector so you still can use LCD if you disable VGA/HDMI
Audio output
Microphone input pads (no connector)
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Fix the name as per DT node naming convention.
- rename the node to syscon which is a more generic name.
- append the register value to the node name.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The minimum recommended ARM voltage for Exynos5250 at 200MHz
on Arndale board is 0.9125V. Update accordingly.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Exynos5420 is octa-core SoC from Samsung.
Hence populate all the CPU node entries.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Exynos5420 is octa-core SoC from Samsung. Hence extend exynos-mct clocksource
driver to support 8 local interrupts.
Also extend dts entries for 8 interrupts.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Adds G-Scaler device nodes to the DT device list
Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds the mmc device tree node entries for exynos5420 SOC.
Exynos5420 has a different version of DWMMC controller,so a new
compatible string is used to distinguish it from the prior SOC's.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch rename's the device tree mmc node's from "dwmmc" to "mmc".
According to ePAPR chapter 2.2.2 generic node name recommendation,
it has been opted change from dwmmc to mmc.Also this patch remove the
instance index from the node name.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
As fifo-depth property in dw_mmc device tree node is SOC
specific, move this property to exynos5250 SOC specific
file.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
[kgene.kim@samsung.com: squashed fifo-depth patch for cros5250-common]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
As per the timing information for supported panel, the value should
be between 47.2 MHz to 47.9 MHz for 60Hz refresh rate.
Total horizontal pixels = 1024 (x-res) + 80 (margin) + 48 (hsync) = 1152
Total vertical pixels = 600 (y-res) + 80 (margin) + 3 (vsync) = 683
Target pixel clock rate for refresh rate @60 Hz
= 1152 * 683 * 60 = 47208960 Hz ~ 47.5 MHz
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
As per the timing information for supported panel, the value should
be between 47.2 MHz to 47.9 MHz for 60Hz refresh rate.
Total horizontal pixels = 1024 (x-res) + 80 (margin) + 48 (hsync) = 1152
Total vertical pixels = 600 (y-res) + 80 (margin) + 3 (vsync) = 683
Target pixel clock rate for refresh rate @60 Hz
= 1152 * 683 * 60 = 47208960 Hz ~ 47.5 MHz
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
According to ePAPR, chapter 2.3.4, the status property has
defined that it should be set to "disabled" when "the device
is not presently operational, but it might become operational
in the future".
So this patch disable dwmmc node by "status = disabled" in SOC
dts file and enable dwmmc node by "status = okay" in board specific
dts file.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add GPIO DT node and pinmux entries for DA850 EVM. GPIO is
configurable differently on different boards. So add GPIO
pinmuxing in dts file.
Signed-off-by: KV Sujith <sujithkv@ti.com>
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This adds very basic device tree files for the Marvell Armada
1500-mini SoC (Berlin BG2CD) and the Google Chromecast. Currently,
SoC only has nodes for cpu, some clocks, l2 cache controller, local
timer, apb timers, uart, and interrupt controllers.
The Google Chromecast is a consumer device comprising the Armada
1500-mini SoC above.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This adds very basic device tree files for the Marvell Armada 1500 SoC
(Berlin BG2) and the Sony NSZ-GS7 GoogleTV board. Currently, SoC only has
nodes for cpus, some clocks, l2 cache controller, local timer, apb timers,
uart, and interrupt controllers. The Sony NSZ-GS7 is a GoogleTV consumer
device comprising the Armada 1500 SoC above.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jisheng Zhang <jszhang@marvell.com>
To be able to enable SDR12|25 for SD-cards, we needed to fixup the
configuration in DT of the gpio regulator, which handles the signal
voltage level. Some configuration were missing and some were wrong.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove duplicated configurations and move specific details into
each corresponding dtsi file for the href versions.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Added device tree support for TI's Keystone USB driver and updated the
Documentation with device tree binding information.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Added device tree support for TI's Keystone USB PHY driver and updated the
Documentation with device tree binding information.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Update the Keystone gic device tree entry to add the maintenance
interrupt information.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Update the Keystone gic node to add the GICV and GIGH address space
needed by the KVM.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
PA subsystem has a fixed factor clock at the input which is
input clock divided by 3. This patch adds this clock node to dts
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This patch adds K2 Kepler/Hawking evm (k2hk-evm) specific dts file.
To enable re-use of bindings across multiple evms of this family,
rename current keystone.dts to keystone.dtsi and include it in the
evm specific dts file.
K2 SoC has separate ref clock inputs for various clocks. So add
separate ref clock nodes for ARM, DDR3A, DDR3B and PA PLL input
clocks in k2hk-evm.dts. While at it, rename refclkmain to
refclksys based on device User Guide naming convention
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Marvell's Armada 370 Reference Design has a NAND flash, so enable it in
the devicetree and add the partitions as prepared in the factory images.
In order to skip the driver's custom device detection and use only ONFI
detection, the "marvell,keep-config" parameter is used. This is needed
because we have no support for setting the timings parameters yet.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The board has 7 buttons connected to GPIOs, add a corresponding
gpio-keys device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch support FSI-AK4648 with simple audio card
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a 'cpus' node to describe the CPU cores of Zynq.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The bindings for the TTC changed in commit 'arm: zynq: Use standard
timer binding' (e932900a32). That change
removed possible subnodes from this driver rendering the 'clock-ranges'
property invalid for this node.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The zynq includes a Cadence GEM IP core. This is compatible with the macb driver.
Add it to the zynq-7000 DT.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Josh Cartwright <josh.cartwright@ni.com>
[soren: rebased to current Linus tree, added zc706 + zed support, moved phy-mode property to board level dtses]
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
