Added has_mailbox to the musb platform data to specify that omap uses
an external mailbox (in control module) to communicate with the musb
core during device connect and disconnect.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A seperate driver has been added to handle the usb part of control
module. A device for the above driver is created here, using the register
address information to be used by the driver for powering on the PHY and
for writing to the mailbox.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we have a separate driver for the control module,
stop populating the control module device data in other modules
(PHY and OTG) device info.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds an IPMMU device and notifies the IPMMU driver which
devices are connected via the IPMMU module. All devices connected to the main
memory bus via the IPMMU module MUST be registered when SHMOBILE_IPMMU and
SHMOBILE_IOMMU are enabled because physical address cannot be used
while the IPMMU module's MMU function is enabled.
Signed-off-by: Hideki EIRAKU <hdk@igel.co.jp>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
This patch adds an IPMMU device and notifies the IPMMU driver which
devices are connected via the IPMMU module. All devices connected to the main
memory bus via the IPMMU module MUST be registered when SHMOBILE_IPMMU and
SHMOBILE_IOMMU are enabled because physical address cannot be used
while the IPMMU module's MMU function is enabled.
Signed-off-by: Hideki EIRAKU <hdk@igel.co.jp>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
This patch adds an IPMMU device and notifies the IPMMU driver which
devices are connected via the IPMMU module. All devices connected to the main
memory bus via the IPMMU module MUST be registered when SHMOBILE_IPMMU and
SHMOBILE_IOMMU are enabled because physical address cannot be used
while the IPMMU module's MMU function is enabled.
Signed-off-by: Hideki EIRAKU <hdk@igel.co.jp>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
The PCI IRQs were regressing due to two things:
- The PCI glue layer was using an hard-coded IRQ 27 offset.
This caused the immediate regression.
- The SIC IRQ mask was inverted (i.e. a bit was indeed set to
one for each valid IRQ on the SIC, but accidentally inverted
in the init call). This has been around forever, but we have
been saved by some other forgiving code that would reserve
IRQ descriptors in this range, as the versatile is
non-sparse.
When the IRQs were bumped up 32 steps so as to avoid using IRQ
zero and avoid touching the 16 legacy IRQs, things broke.
Introduce an explicit valid mask for the IRQs that are active
on the PIC/SIC, and pass that. Use the BIT() macro from
<linux/bitops.h> to make sure we hit the right bits, readily
defined in <mach/platform.h>.
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 91c2ebb90b (ARM: 7114/1: cache-l2x0: add resume entry for l2
in secure mode) added resume entry for l2 in secure mode, but it missed
the dummy entry when CONFIG_CACHE_L2X0 is not set.
(Commit text edited by rmk.)
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From Kukjin Kim:
This is 4th cleanup for Samsung S3C24XX stuff, and removes plat-s3c24xx
directory.
* 'next/cleanup-s3c24xx-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S3C24XX: header mach/regs-mem.h local
ARM: S3C24XX: header mach/regs-power.h local
ARM: S3C24XX: header mach/regs-s3c2412-mem.h local
ARM: S3C24XX: Remove plat-s3c24xx directory in arch/arm/
From Kukjin Kim:
This is redoing the s3c24xx irqs in a generic way by using a declarative
approach.
* 'next/irq-s3c24xx' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S3C24XX: transform s3c2443 subirqs into new structure
ARM: S3C24XX: modify s3c2443 irq init to initialize all irqs
ARM: S3C24XX: move s3c2443 irq code to irq.c
ARM: S3C24XX: transform s3c2416 irqs into new structure
ARM: S3C24XX: modify s3c2416 irq init to initialize all irqs
ARM: S3C24XX: move s3c2416 irq init to common irq code
ARM: S3C24XX: Modify s3c_irq_wake to use the hwirq property
ARM: S3C24XX: Move irq syscore-ops to irq-pm
ARM: S3C24XX: transform irq handling into a declarative form
Signed-off-by: Olof Johansson <olof@lixom.net>
- Sort out imx DEBUG_LL uart port selection
- A couple of imx_v6_v7_defconfig updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJREHAwAAoJEFBXWFqHsHzOONMIAK/w88b7mCNmwOgV+nEDZGfm
17rVGXZV4YdR4bpOFBdbMMddf16Yb5ENH5AHDwlYzr8zzZE0ODOjrQ5Pmk1aA9VR
EsJVIKpS9FnU6tvUIEnYPTK+PDkf44IW/bDb9BdbptVQmnWP/hTtYDcx7ruTSZx4
OK/Z9oz3Hwwl8+AfWh67tZ/nqJg7eugGwctM6IxMOH7dUCuJ5DALF9dYn3NCqC6b
oqkzbNpSdg2MicUINiMOEbQvoZfGgpC6CH/nWCSIjNWss0bbakpF5iqk0aU7+/0k
tNtbKFIAKgcHF4t0P0RyI6Qyt03tPBF2tUobuCEtwdBDT3jWFrkpUpImFLyE5+I=
=0R2N
-----END PGP SIGNATURE-----
Merge tag 'imx-soc-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/soc
From Shawn Guo:
imx soc changes for 3.9
- Sort out imx DEBUG_LL uart port selection
- A couple of imx_v6_v7_defconfig updates
* tag 'imx-soc-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx_v6_v7_defconfig: enable anatop regulator and snvs rtc
ARM: imx: support DEBUG_LL uart port selection for all i.MX SoCs
ARM: imx: use separated debug uart symbol for imx31 and imx35
ARM: imx_v6_v7_defconfig: Select IPUV3 driver
Commit 816a65ef4 (ARM: OMAP2+: Limit omap initcalls to omap only on
multiplatform kernels) fixed up things for multiplatform booting
but failed to include soc.h causing a new warning:
arch/arm/mach-omap2/hwspinlock.c:60:1: warning: data definition has no type or storage class
arch/arm/mach-omap2/hwspinlock.c:60:1: warning: type defaults to 'int' in declaration of 'omap_postcore_initcall'
arch/arm/mach-omap2/hwspinlock.c:60:1: warning: parameter names (without types) in function declaration
arch/arm/mach-omap2/hwspinlock.c:31:122: warning: 'hwspinlocks_init' defined but not used
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
things to device tree based booting.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=mdSV
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.9/board-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/boards
From Tony Lindgren:
Minimal updates to OMAP board-*.c files while converting
things to device tree based booting.
* tag 'omap-for-v3.9/board-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: omap2plus_defconfig: enable omap1 rtc
RX-51: Register twl4030-madc device
RX-51: Add leds lp5523 names from Maemo 5 2.6.28 kernel
ARM: OMAP2+: AM33XX: omap2plus_defconfig: Add support for few drivers
ARM: OMAP1: nokia770: enable CBUS/Retu
ARM: OMAP2+: omap2plus_defconfig: enable CMA allocator
ARM: OMAP2+: omap2plus_defconfig: enable TFP410 chip support
ARM: OMAP3: igep0020: simplify GPIO LEDs dependencies
ARM: OMAP2+: craneboard: support the TPS65910 PMU
ARM: OMAP2+: craneboard: support NAND device
ARM: OMAP3: cm-t3517: add MMC support
ARM: OMAP2+: Remove apollon board support
+ Linux 3.8-rc6
Signed-off-by: Olof Johansson <olof@lixom.net>
Remove some dead OMAP clock and device integration code and data.
Also, clean up the way that the OMAP device integration code blocks
WFI/WFE to use a consistent mechanism, controlled by a data flag.
Several OMAP2+ power management fixes, optimizations, and cleanup.
This series is a prerequisite for the functional powerdomain
conversion series.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Rhql
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.9/pm-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
From Tony Lindgren:
OMAP PM related updates via Paul Walmsley <paul@pwsan.com>:
Remove some dead OMAP clock and device integration code and data.
Also, clean up the way that the OMAP device integration code blocks
WFI/WFE to use a consistent mechanism, controlled by a data flag.
Several OMAP2+ power management fixes, optimizations, and cleanup.
This series is a prerequisite for the functional powerdomain
conversion series.
* tag 'omap-for-v3.9/pm-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: powerdomain: fix whitespace, improve flag comments
ARM: OMAP2+: clockdomain: convert existing atomic usecounts into spinlock-protected shorts/ints
ARM: OMAP2+: clockdomain: work on wkdep/sleepdep functions
ARM: OMAP2xxx: CM: remove autodep handling
ARM: OMAP2+: powerdomain/clockdomain: add a per-powerdomain spinlock
ARM: OMAP2+: PM/powerdomain: move omap_set_pwrdm_state() to powerdomain code
ARM: OMAP2: PM/powerdomain: drop unnecessary pwrdm_wait_transition()
ARM: OMAP2xxx: PM: clean up some crufty powerstate programming code
ARM: OMAP2+: clockdomain: add pwrdm_state_switch() call to clkdm_sleep()
ARM: OMAP2+: powerdomain: fix powerdomain trace integration
ARM: OMAP4: MPUSS PM: remove unnecessary shim functions for powerdomain control
ARM: OMAP3xxx: CPUIdle: optimize __omap3_enter_idle()
ARM: OMAP2420: hwmod data/PM: use hwmod to block WFI when I2C active
ARM: OMAP2+: hwmod: add support for blocking WFI when a device is active
ARM: OMAP3xxx: CPUIdle: simplify the PER next-state code
ARM: OMAP2xxx: powerdomain: core powerdomain missing logic retention states
ARM: OMAP2xxx: clock data: clean up unused null clocks
ARM: OMAP4: clock/hwmod data: remove MODULEMODE entries in mux + gate combos
ARM: OMAP4: clock/hwmod data: start to remove some IP block control "clocks"
ARM: OMAP2+: omap_device: remove obsolete pm_lats and early_device code
the -rc series.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=IZZq
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.9/fixes-non-critical-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/fixes-non-critical
From Tony Lindgren:
Few fixes for v3.9 merge window that are not urgent for
the -rc series.
* tag 'omap-for-v3.9/fixes-non-critical-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: using strlcpy instead of strncpy
ARM: OMAP2+: Fix selection of clockevent timer when using device-tree
ARM: OMAP: Fix the use of uninitialized dma_lch_count
ARM: OMAP: make wakeupgen_lock raw
+ Linux 3.8-rc6
Various new features are enabled on Tegra:
* RTC_DRV_TPS6586X to enable the RTC on many boards, such as Harmony
and Ventana.
* POWER_RESET_GPIO to provide a power off driver for TrimSlice.
* Tegra KBC controller support, for Seaboard, Harmony, and Whistler.
* Tegra high-speed UART driver, for Cardhu Bluetooth.
* kexec support.
This pull request is based on v3.8-rc3.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=W9Vp
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.9-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/boards
From Stephen Warren:
ARM: tegra: defconfig update
Various new features are enabled on Tegra:
* RTC_DRV_TPS6586X to enable the RTC on many boards, such as Harmony
and Ventana.
* POWER_RESET_GPIO to provide a power off driver for TrimSlice.
* Tegra KBC controller support, for Seaboard, Harmony, and Whistler.
* Tegra high-speed UART driver, for Cardhu Bluetooth.
* kexec support.
This pull request is based on v3.8-rc3.
* tag 'tegra-for-3.9-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: tegra: defconfig updates
Numerous updates to the various Tegra device trees are made:
* Addition of NVIDIA Beaver (Tegra30) and Toradex Colibri T20 and Iris
carrier boards.
* Enablement of the HDMI connector on most boards.
* Enablement of the keyboard controller on a few boards.
* Addition of the AC'97 controller to Tegra20.
* Addition of a GPIO poweroff node for TrimSlice.
* Changes to support the new "high speed UART" (DMA-capable) driver for
Tegra serial ports, and enablement for Cardhu's UART C.
* A few cleanups, such as compatible flag fixes, node renames, node
ordering fixes, commonizing properties into SoC .dtsi files, etc..
This pull request is based on (most of) the previous pull request with
tag tegra-for-3.9-soc-t114.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=UMMs
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.9-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/dt
From Stephen Warren:
ARM: tegra: device tree updates
Numerous updates to the various Tegra device trees are made:
* Addition of NVIDIA Beaver (Tegra30) and Toradex Colibri T20 and Iris
carrier boards.
* Enablement of the HDMI connector on most boards.
* Enablement of the keyboard controller on a few boards.
* Addition of the AC'97 controller to Tegra20.
* Addition of a GPIO poweroff node for TrimSlice.
* Changes to support the new "high speed UART" (DMA-capable) driver for
Tegra serial ports, and enablement for Cardhu's UART C.
* A few cleanups, such as compatible flag fixes, node renames, node
ordering fixes, commonizing properties into SoC .dtsi files, etc..
This pull request is based on (most of) the previous pull request with
tag tegra-for-3.9-soc-t114.
* tag 'tegra-for-3.9-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (22 commits)
ARM: dt: tegra30: Rename "smmu" to "iommu"
ARM: dt: tegra20: Rename "gart" to "iommu"
ARM: tegra: move serial clock-frequency attr into the Tegra30 dtsi
ARM: tegra: Add Toradex Iris carrier board DT with T20 512MB COM
ARM: tegra: Add Colibri T20 512MB COM device tree
ARM: tegra: move serial clock-frequency attr into the Tegra20 dtsi
ARM: tegra: harmony: enable keyboard in DT
ARM: tegra: whistler: enable keyboard in DT
ARM: tegra: cardhu: register UARTC
ARM: tegra: seaboard: enable keyboard in DT
ARM: tegra: add DT entry for KBC controller
ARM: tegra: swap cache-/interrupt-ctrlr nodes in DT
ASoC: tegra: add ac97 host controller to device tree
ARM: DT: tegra: Add Tegra30 Beaver board support
ARM: DT: tegra: Add board level compatible properties
ARM: tegra: paz00: enable HDMI port
ARM: tegra: ventana: enable HDMI port
ARM: tegra: seaboard: enable HDMI port
ARM: tegra: trimslice: add gpio-poweroff node to DT
ARM: DT: tegra: Unify the description of Tegra20 boards
...
Based on two separate cleanup branches, it's now empty and can be removed.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Stephen Warren <swarren@wwwdotorg.org>
This pull request adds initial support for the Tegra114 SoC, which
integrates a quad-core ARM Cortex-A15 CPU. I'm proud to observe that we
posted the initial versions of these patches before the final official
announcement of this chip.
These patches are enough to boot with a UART-based console, support the
Dalmore and Pluto reference/evaluation boards, instantiate the GPIO and
pinctrl drivers, and enable a cpuidle state. As yet, no clocks or
storage devices are supported, but patches for those will follow shortly.
This pull request is based on (most of) the previous pull request with
tag tegra-for-3.9-soc-cpuidle, followed by a merge of the previous pull
request with tag tegra-for-3.9-scu-base-rework.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=bIIe
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.9-soc-t114' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
From Stepen Warren:
ARM: tegra: add Tegra114 SoC support
This pull request adds initial support for the Tegra114 SoC, which
integrates a quad-core ARM Cortex-A15 CPU. I'm proud to observe that we
posted the initial versions of these patches before the final official
announcement of this chip.
These patches are enough to boot with a UART-based console, support the
Dalmore and Pluto reference/evaluation boards, instantiate the GPIO and
pinctrl drivers, and enable a cpuidle state. As yet, no clocks or
storage devices are supported, but patches for those will follow shortly.
This pull request is based on (most of) the previous pull request with
tag tegra-for-3.9-soc-cpuidle, followed by a merge of the previous pull
request with tag tegra-for-3.9-scu-base-rework.
* tag 'tegra-for-3.9-soc-t114' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (24 commits)
ARM: DT: tegra114: add pinmux DT entry
ARM: DT: tegra114: add GPIO DT entry
ARM: tegra114: select PINCTRL for Tegra114 SoC
ARM: tegra: add Tegra114 ARM_CPUIDLE_WFI_STATE support
ARM: tegra: Add SMMU entry to Tegra114 DT
ARM: tegra: add AHB entry to Tegra114 DT
ARM: tegra: Add initial support for Tegra114 SoC.
ARM: dt: tegra114: Add new board, Pluto
ARM: dt: tegra114: Add new board, Dalmore
ARM: dt: tegra114: Add new SoC base, Tegra114 SoC
ARM: tegra: fuse: Add chip ID Tegra114 0x35
ARM: OMAP: Make use of available scu_a9_get_base() interface
ARM: tegra: Skip scu_enable(scu_base) if not Cortex A9
ARM: Add API to detect SCU base address from CP15
ARM: tegra: Use DT /cpu node to detect number of CPU core
ARM: tegra: Add CPU nodes to Tegra30 device tree
ARM: tegra: Add CPU nodes to Tegra20 device tree
ARM: perf: simplify __hw_perf_event_init err handling
ARM: perf: remove unnecessary checks for idx < 0
ARM: perf: handle armpmu_register failing
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Remove/add conflict in arch/arm/mach-tegra/common.c resolved.
Remove/remove conflict in arch/arm/mach-tegra/platsmp.c. Leave the empty
stub function for now since removing it in the merge commit is confusing;
will be cleaned up in a separate commit. # # It looks like you may be
committing a merge. # If this is not correct, please remove the file #
.git/MERGE_HEAD # and try again.
This pull request implements a new "LP2" cpuidle state for Tegra20,
which makes use of the couple cpuidle feature.
It is based on (most of) the previous pull request, with tag
tegra-for-3.9-soc-usb.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=2BUE
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.9-soc-cpuidle' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
From Stephen Warren:
ARM: tegra: cpuidle enhancements
This pull request implements a new "LP2" cpuidle state for Tegra20,
which makes use of the couple cpuidle feature.
It is based on (most of) the previous pull request, with tag
tegra-for-3.9-soc-usb.
* tag 'tegra-for-3.9-soc-cpuidle' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: tegra20: cpuidle: apply coupled cpuidle for powered-down mode
ARM: tegra20: flowctrl: add support for cpu_suspend_enter/exit
clk: tegra20: Implementing CPU low-power function for tegra_cpu_car_ops
ARM: tegra20: cpuidle: add powered-down state for secondary CPU
ARM: tegra: add pending SGI checking API
Signed-off-by: Olof Johansson <olof@lixom.net>
Without this patch the adv7343 encoder was being set to default
configuration which caused display not to work on this board.
This patch passes the necessary platform data required for adv7343
encoder to work on da850 evm.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Tegra USB driver has a number of issues:
1) The PHY driver isn't a true platform device, and doesn't implement
the standard USB PHY API.
2) struct device instance numbers were used to make decisions in the
driver, rather than being parameterized by DT or platform data.
This pull request solves issue (2), and lays the groundwork for solving
issue (1). The work on issue (1) involved introducing new DT nodes for
the USB PHYs, which in turn interacted with the Tegra common clock
framework changes, due to the move of clock lookups into device tree.
Hence, these USB driver changes are taken through the Tegra tree with
acks from USB maintainers.
This pull request is based on the previous pull request, with tag
tegra-for-3.9-soc-ccf.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=8pTe
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.9-soc-usb' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
From Stephen Warren:
ARM: tegra: USB driver cleanup
The Tegra USB driver has a number of issues:
1) The PHY driver isn't a true platform device, and doesn't implement
the standard USB PHY API.
2) struct device instance numbers were used to make decisions in the
driver, rather than being parameterized by DT or platform data.
This pull request solves issue (2), and lays the groundwork for solving
issue (1). The work on issue (1) involved introducing new DT nodes for
the USB PHYs, which in turn interacted with the Tegra common clock
framework changes, due to the move of clock lookups into device tree.
Hence, these USB driver changes are taken through the Tegra tree with
acks from USB maintainers.
This pull request is based on the previous pull request, with tag
tegra-for-3.9-soc-ccf.
* tag 'tegra-for-3.9-soc-usb' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
usb: host: tegra: make use of PHY pointer of HCD
ARM: tegra: Add reset GPIO information to PHY DT node
usb: host: tegra: don't touch EMC clock
usb: add APIs to access host registers from Tegra PHY
USB: PHY: tegra: Get rid of instance number to differentiate PHY type
USB: PHY: tegra: get rid of instance number to differentiate legacy controller
ARM: tegra: add clocks properties to USB PHY nodes
ARM: tegra: add DT nodes for Tegra USB PHY
usb: phy: remove unused APIs from Tegra PHY.
usb: host: tegra: Resetting PORT0 based on information received via DT.
ARM: tegra: Add new DT property to USB node.
usb: phy: use kzalloc to allocate struct tegra_usb_phy
ARM: tegra: remove USB address related macros from iomap.h
Tegra already supports the common clock framework, but had issues:
1) The clock driver was located in arch/arm/mach-tegra/ rather than
drivers/clk/.
2) A single "Tegra clock" type was implemented, rather than separate
clock types for PLL, mux, divider, ... type in HW.
3) Clock lookups by device drivers were still driven by device name
and connection ID, rather than through device tree.
This pull request solves all three issues. This required some DT changes
to add clocks properties, and driver changes to request clocks more
"correctly". Finally, this rework allows all AUXDATA to be removed from
Tegra board files, and various duplicate clock lookup entries to be
removed from the driver.
This pull request is based on the previous pull request, with tag
tegra-for-3.9-cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=s9hz
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.9-soc-ccf' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
From Stephen Warren:
ARM: tegra: Common Clock Framework rework
Tegra already supports the common clock framework, but had issues:
1) The clock driver was located in arch/arm/mach-tegra/ rather than
drivers/clk/.
2) A single "Tegra clock" type was implemented, rather than separate
clock types for PLL, mux, divider, ... type in HW.
3) Clock lookups by device drivers were still driven by device name
and connection ID, rather than through device tree.
This pull request solves all three issues. This required some DT changes
to add clocks properties, and driver changes to request clocks more
"correctly". Finally, this rework allows all AUXDATA to be removed from
Tegra board files, and various duplicate clock lookup entries to be
removed from the driver.
This pull request is based on the previous pull request, with tag
tegra-for-3.9-cleanup.
* tag 'tegra-for-3.9-soc-ccf' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (31 commits)
clk: tegra30: remove unused TEGRA_CLK_DUPLICATE()s
clk: tegra20: remove unused TEGRA_CLK_DUPLICATE()s
ARM: tegra30: remove auxdata
ARM: tegra20: remove auxdata
ASoC: tegra: remove auxdata
staging: nvec: remove use of clk_get_sys
ARM: tegra: paz00: add clock information to DT
ARM: tegra: add clock properties to Tegra30 DT
ARM: tegra: add clock properties to Tegra20 DT
spi: tegra: do not use clock name to get clock
ARM: tegra: remove legacy clock code
ARM: tegra: migrate to new clock code
clk: tegra: add clock support for Tegra30
clk: tegra: add clock support for Tegra20
clk: tegra: add Tegra specific clocks
ARM: tegra: define Tegra30 CAR binding
ARM: tegra: define Tegra20 CAR binding
ARM: tegra: move tegra_cpu_car.h to linux/clk/tegra.h
ARM: tegra: add function to read chipid
ARM: tegra: fix compile error when disable CPU_IDLE
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/mach-tegra/board-dt-tegra20.c
arch/arm/mach-tegra/board-dt-tegra30.c
arch/arm/mach-tegra/common.c
arch/arm/mach-tegra/platsmp.c
drivers/clocksource/Makefile
This pull request contains various cleanup and minor changes to core
Tegra code:
* Tegra clocksource driver is moved to drivers/clocksource.
* Various typos, warning cleanup, statics cleanup, section mismatch
fixes, etc.
* Various small fixes/cleanups for CPU/hotplug/SMP code.
This pull request is based on a merge of v3.8-rc3 and at least part of
arm-soc's timer/cleanup branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=H2vV
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.9-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/cleanup
From Stephen Warren:
ARM: tegra: cleanup
This pull request contains various cleanup and minor changes to core
Tegra code:
* Tegra clocksource driver is moved to drivers/clocksource.
* Various typos, warning cleanup, statics cleanup, section mismatch
fixes, etc.
* Various small fixes/cleanups for CPU/hotplug/SMP code.
This pull request is based on a merge of v3.8-rc3 and at least part of
arm-soc's timer/cleanup branch.
* tag 'tegra-for-3.9-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: tegra: fix compile error when disable CPU_IDLE
ARM: tegra30: make the wait time of CPU power up to proportional to HZ
ARM: tegra: make device can run on UP
ARM: tegra: clean up the CPUINIT section
ARM: tegra: moving the clock gating procedure to tegra_cpu_kill
ARM: tegra: update the cache maintenance order for CPU shutdown
ARM: tegra30: fix power up sequence for boot_secondary
ARM: tegra: cpufreq: move clk_get/put out of function tegra_cpu_init/exit
ARM: tegra: fix Kconfig warnings when !SMP
ARM: tegra: Make variables static
clocksource: tegra: cosmetic: Fix error message
ARM: tegra: move timer.c to drivers/clocksource/
Signed-off-by: Olof Johansson <olof@lixom.net>
Trivial conflicts:
arch/arm/mach-tegra/board-dt-tegra20.c
arch/arm/mach-tegra/board-dt-tegra30.c
drivers/clocksource/Makefile
Newer Exynos4 SoC are equipped with a local camera ISP that
controls external raw image sensor directly. Such sensors
can be connected through FIMC-LITEn (and MIPI-CSISn) IPs to
the ISP, which then feeds image data to the FIMCn IP. Thus
there can be two busses associated with an image source
(sensor). Rename struct s5p_fimc_isp_info describing external
image sensor (video decoder) to struct fimc_source_info to
avoid confusion. bus_type is split into fimc_bus_type and
sensor_bus_type. The bus type enumeration is extended to
include both FIMC Writeback input types.
The bus_type enumeration and the data structure name in the
board files are modified according to the above changes.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A fix for r8a7779 clocks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=FX9R
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc3-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
From Simon Horman:
Third round of Renesas ARM-based SoC changes for v3.9
A fix for r8a7779 clocks.
* tag 'renesas-soc3-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7779: Correct TMU clock support
With the recent twl related changes we can now get:
WARNING: arch/arm/mach-omap2/built-in.o(.text+0x15f88): Section mismatch in
reference from the function sdp3430_twl_gpio_setup() to the function
.init.text:omap_twl4030_audio_init()
The function sdp3430_twl_gpio_setup() references
the function __init omap_twl4030_audio_init().
This is often because sdp3430_twl_gpio_setup lacks a __init
annotation or the annotation of omap_twl4030_audio_init is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0x16968): Section mismatch in
reference from the function zoom_twl_gpio_setup() to the function
.init.text:omap_twl4030_audio_init()
The function zoom_twl_gpio_setup() references
the function __init omap_twl4030_audio_init().
This is often because zoom_twl_gpio_setup lacks a __init
annotation or the annotation of omap_twl4030_audio_init is wrong.
Fix this by removing __init from omap_twl4030_audio_init() as
suggested by Peter Ujfalusi <peter.ujfalusi@ti.com>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
- It fixes fec ptp clock pointer in device tree source.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJREL7uAAoJEFBXWFqHsHzO+1cH+QEeUwTqmlI2enO7XOxb4F5q
OijafxIi8+pYfQOZ6v/E70SaBaMyHQpG4WY3zQ+lrQlM/qCqAeEB/9KbkQU/1n8e
e1NF1Px/QisTcTF7qKwHhKurzgbuZ4vApX+IwCJyoGpYdEup9DxQxYvIqjUrwbdp
OdJ76kRkMkhj5D1WKRBOypStMRnDBr6e8Scc2iQspw8K9U1w+2g5kADGYGatEzOr
EcZ+EHIXJcBbX2938wakStshsanUlJEjdRbiQE8LQgaYYyHi9+S/xMvgDugwKbHY
OtOZ+vtQMOHeiusDQ01g7O3ZnsipWVMdk50hgBXxOZl4UHBHshQg5fG1dW+34Dw=
=2plf
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.8-4' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo:
imx fixes for 3.8, take 4
- It fixes fec ptp clock pointer in device tree source.
* tag 'imx-fixes-3.8-4' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: dts: imx6: fix fec ptp clock slow 10 time
-Compile fix for !SMP
-More cpu cluster id related fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRDSkpAAoJEMhvYp4jgsXiSWYH/jy92oAHpKoNBZQ0wzOVXoa7
Lo9vkPaTexXY1SLNohrTiGDxWwm7LNfi6Lag3OtzyzAblcUAqd6ISyx2Nh7xN3Uu
L+3Y7CIBw9CqCAsrjOunMmKcawo/aiscAlhqOoYsmKGcbopQHEomui+yfDIX6NY+
v59xDXp1IyJHqDc9M3t2VJijfeCHnREIddt33gUeEcSfL7nyuvGf2DXuarAGN5N7
bHd7NxqZS2TNGxTbxuNZIlYuVUgqcVV16LLNlTGrBb27iiPJuIg3uHa6GVVO4n0U
czd388xl5Rca8LeD7rAvWPiHX2rIfyEyvWZO4KvRBC9H6+VgGvlyKtnoUPyNhn8=
=mUYd
-----END PGP SIGNATURE-----
Merge tag 'highbank-fixes-for-3.8' of git://sources.calxeda.com/kernel/linux into fixes
From Rob Herring:
highbank fixes for 3.8
-Compile fix for !SMP
-More cpu cluster id related fixes
* tag 'highbank-fixes-for-3.8' of git://sources.calxeda.com/kernel/linux:
ARM: highbank: mask cluster id from cpu_logical_map
ARM: scu: mask cluster id from cpu_logical_map
ARM: scu: add empty scu_enable for !CONFIG_SMP
The Nomadik Device Tree patch series accidentally
selected OF instead of USE_OF which led to problems
during compile:
arch/arm/kernel/devtree.c: In function 'arm_dt_memblock_reserve':
/home/elinwal/linux-arm-soc/arch/arm/kernel/devtree.c:43:7: error: 'initial_boot_params' undeclared (first use in this function)
(etc).
This fixes it up by selecting USE_OF instead.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
are unused on ARM architecure. Samsung has some code setting up wdog
in arch_decomp_wdog(). But since CONFIG_S3C_BOOT_WATCHDOG is defined
nowhere, it will not run. Otherwise, system can not boot at all when
wdog is set up but no one pats it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQ9WSiAAoJEFBXWFqHsHzOkpYH/iHOomqWknjg0YjeUKmoqnk+
UnAiP/OD0pOuqdC3izSq5rAaxeCn2ESYhXWdHH3LQFNnhwDPOItagY3T1dBgJH0G
KvO3wDj0K1jUM6Nzt4hta4pnCc/KClyCcVjYrP5pE+bs3NzOzxvfj2tPc81lI0Iy
rnkMLWw6gVRllhecUezt3TOd/GfI7NwuyjjBOLelOerbImWFqLOCNIZSRQlazbyS
hFh4OkR7yoU6vEvPdmS4B4A5PWBHlxiUS6Wr4v+doGFPiFgR05tJodLnnJ/KGWmG
LFY99MyeBvcgiUlFcUpiVLYpWJh+7IB1LJH+IGNJbWFYC+Yvn/o9IRYO8kvuiYE=
=weNJ
-----END PGP SIGNATURE-----
Merge tag 'cleanup-decompwdog-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/cleanup
From Shawn Guo:
The series cleans up ARCH_HAS_DECOMP_WDOG and arch_decomp_wdog which
are unused on ARM architecure. Samsung has some code setting up wdog
in arch_decomp_wdog(). But since CONFIG_S3C_BOOT_WATCHDOG is defined
nowhere, it will not run. Otherwise, system can not boot at all when
wdog is set up but no one pats it.
* tag 'cleanup-decompwdog-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: samsung: remove unused arch_decomp_wdog() code
ARM: remove unused arch_decomp_wdog()
ARM: decompress: remove unused ARCH_HAS_DECOMP_WDOG
Signed-off-by: Olof Johansson <olof@lixom.net>
Since pinctrl-exynos can support exynos4 and exynos5 so changed
the option name to PINCTRL_EXYNOS for more clarity.
Cc: Thomas Abraham <Thomas.abraham@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add AB8540 sub driver to the ABx500 family, pins, pin groups and
gpio range.
As the pin controller (also the ABx500 controllers) is an
inherent part of the SoC and will prevent boot if not
available, select this from the Ux500 SoC Kconfig.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add AB9540 sub driver to the ABx500 family, pins, pin groups and
gpio range.
As the pin controller (also the ABx500 controllers) is an
inherent part of the SoC and will prevent boot if not
available, select this from the Ux500 SoC Kconfig.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add AB8505 sub driver to the ABx5x family.
As the pin controller (also the ABx500 controllers) is an
inherent part of the SoC and will prevent boot if not
available, select this from the Ux500 SoC Kconfig.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix the use of USART on both at91sam9x5 and at91sam9n12. In DTS, the
atmel,use-dma-[rx|tx] property is present but a DMA channel cannot be used.
Indeed the connexion between the DMA engine and the slave is not implemented
yet in Device Tree.
Note however that this property is also used for PDC (private DMA) on older
SoCs. This is why the driver alone cannot determine the validity of this
property.
Reported-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable <stable@vger.kernel.org> [3.8+]
The mxc-timer on the imx25 needs to be derived from the AHB clock.
If a bootloader reparents this clock to the ipg_clk_highfreq, which according
to the datasheet is a valid operation, the system can/will produce lockups/
freezes after some time [1].
This can be forced with code like
while(1)
syscall(SYS_clock_gettime, CLOCK_REALTIME, &tp);
This was already fixed with the commit
"i.MX25 GPT clock fix: ensure correct the clock source" [2],
for 3.1-rc2, but was lost, when i.MX was converted to the common clock framework
("ARM i.MX25: implement clocks using common clock framework") [3]
[1]: http://lists.arm.linux.org.uk/lurker/message/20130129.161230.229bda17.en.html
[2]: 2012d9ca2a
[3]: 6bbaec5676
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: stable@vger.kernel.org # v3.5+
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
spi-imx driver needs two clock: ipg and per. The first clock must be named and
the second must be added.
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Register ARM architected timer by default for all mach-shmobile
systems using late timer.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
ptp should use enet_ref instead of pll6_enet
pll6_enet is fixed 500Mhz.
There are divider between enet_ref and pll6_enet
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
- use rtc-mv in mvebu armv7 SoCs
- add pci-e hotplug for kirkwood
Depends on:
- tags/mvebu_fixes_for_v3.8-rc6
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRCqOnAAoJEAi3KVZQDZAewlUH/04tpMdf2rvgNP8uUVPVx62T
cXMga9qLTyXQ9hn31KP7fd/JPLRJFsG/+jy4x687EurJGIXXaWGNadjlE69DEPAZ
jt78sPa+Mo/xYD4XoNCr/ng1cbnTwc1ebSRSfN+nIjWynE8Do7tkOKxfJodTgQCM
XbE3EHfvAktKfJTsFDPsFwoIycEYxFsN4jQPwiCdPHVb24py3FWBy+qep7wtLfSO
gTnakEcOsQc7aFzrFdZ1ZnQ9KRlBYXVN636o4sQkM+UM9Vf7FAWBM4OCi2KP4trU
IlTzknoMAMYat+AtYzq1FcDmajeP/EgG6DbQh7lqUK0LEILn2rdAUlgN2QB3VIs=
=6oef
-----END PGP SIGNATURE-----
Merge tag 'drivers_for_v3.9' of git://git.infradead.org/users/jcooper/linux into next/soc
From Jason Cooper:
mvebu drivers for v3.9
- use rtc-mv in mvebu armv7 SoCs
- add pci-e hotplug for kirkwood
Depends on:
- tags/mvebu_fixes_for_v3.8-rc6
* tag 'drivers_for_v3.9' of git://git.infradead.org/users/jcooper/linux:
cpuidle: kirkwood: Move out of mach directory
rtc: Add support of rtc-mv for MVEBU SoCs
ARM: Kirkwood: Support basic hotplug for PCI-E
arm: mvebu: i2c come back in defconfig
arm: plat-orion: fix printing of "MPP config unavailable on this hardware"
Dove: activate GPIO interrupts in DT
- It's based on imx-cleanup-3.9 to avoid conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRCRzjAAoJEFBXWFqHsHzOOTYH/2YiAhCXDoovJ++leTTBKoFO
kRx2gvV0oxQYAjvRX4IiiwcuWjbCQI8ugiKxeH9Vn+jwHD8jKqzTINEUVQfKUud6
s8AI1/EqKwKnEFYFs/Fg6WxZHuHpoL/clpRB/5wZw1KoChmte2OnVU7d9vOt67iN
l0P4nPR18iwU5LFoDCnqMX50Dp9C56KEF2JhzBCQKW9TtRclwpcBNy6AsHb/TNOe
/nHN+Ku6/3xQEz2MPQ9QdmgFxnp9Pr8R6leJNg1Vg6UGRYrKxy0zVo+oFEXAZuUw
v6gnhdlvO6Ki/IKHcWkw7Q7pUDTuB6SttirQE9mBlPdc0V3kTU82SVtX9WAQhSs=
=rVol
-----END PGP SIGNATURE-----
Merge tag 'imx6q-cpudile-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/soc
From Shawn Guo:
imx6q cpuidle support for 3.9
- It's based on imx-cleanup-3.9 to avoid conflicts.
* tag 'imx6q-cpudile-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx6q: support WAIT mode using cpuidle
ARM: imx: move imx6q_cpuidle_driver into a separate file
ARM: imx: mask gpc interrupts initially
ARM: imx: return zero in case next event gets a large increment
ARM: imx: Remove mx508 support
ARM: imx: Remove mach-mx51_3ds board
ARM: imx: use debug_ll_io_init() for imx6q
ARM: imx: remove unused imx6q_clock_map_io()
ARM: mach-imx: Kconfig: Do not select Babbage for MACH_IMX51_DT
Signed-off-by: Olof Johansson <olof@lixom.net>
Still, two delete/change conflicts caused by imx/cleanup:
arch/arm/mach-imx/mach-mx50_rdp.c
arch/arm/mach-imx/mach-mx51_3ds.c
Fix the issue:
tree: git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc.git next/soc
head: 6ed05a2aab
commit: af70fdc947 [4/8] Merge branch 'marco-timer-cleanup-rebase' of
git://gitorious.org/sirfprima2-kernel/sirfprima2-kernel into next/soc
config: make ARCH=arm prima2_defconfig
All error/warnings:
>> arch/arm/mach-prima2/platsmp.c:20:30: fatal error: asm/hardware/gic.h: No such file or directory
compilation terminated.
--
>> arch/arm/mach-prima2/common.c:15:30: fatal error: asm/hardware/gic.h: No such file or directory
compilation terminated.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Cc: Xie ChanglongX <changlongx.xie@intel.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
