From Kukjin Kim:
AS I commented, this makes <mach/*.h> local so that they could be removed.
* 'next/cleanup-header' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (26 commits)
ARM: S3C64XX: Fix missing header error with CONFIG_CPU_IDLE enabled
ARM: S3C64XX: make regs-syscon-power.h local
ARM: S3C64XX: make regs-sys.h local
ARM: S3C64XX: make regs-srom.h local
ARM: S3C64XX: make regs-modem.h local
ARM: S3C64XX: make regs-gpio-memport.h local
ARM: S3C64XX: make crag6410.h local
ARM: S3C24XX: remove dsc.c and make regs-dsc.h local
ARM: S3C24XX: remove idle.h
ARM: S3C2412: cleanup regs-s3c2412.h
ARM: S3C2416: remove regs-s3c2416-mem.h and regs-s3c2416.h
ARM: S3C24XX: make vr1000-cpld.h, vr1000-irq.h and vr1000-map.h local
ARM: S3C24XX: make otom-map.h local
ARM: S3C24XX: make osiris-cpld.h and osiris-map.h local
ARM: S3C24XX: make h1940.h and h1940-latch.h local
ARM: S3C24XX: make gta02.h local
ARM: S3C24XX: make bast-cpld.h, bast-irq.h and bast-map.h local
ARM: S3C24XX: make anubis-cpld, anubis-irq and anubis-map local
ARM: SAMSUNG: cleanup mach/gpio-fns.h gpio-track.h and gpio-nrs.h
ARM: SAMSUNG: cleanup mach/regs-audss.h file
...
Signed-off-by: Olof Johansson <olof@lixom.net>
During code review it was noticed that the clock value for
TMU01 was incorrect and the value for TMU02 was missing.
For reference: As of 3.8-rc6 there are no in-tree consumes of these clocks.
Reported-by: Denis Oliver Kropp <dok@directfb.org>
Reviewed-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Newer versions of udev (such as 182) requires CONFIG_DEVTMPFS_MOUNT to be
selected, otherwise we get a stuck console:
Starting udev
Starting Bootlog daemon: bootlogd: cannot deduce real console device
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
timer resolution of ~32us is pretty low.
v2 has 32bits resolution, so we have quite some headroom, and
can use the 24MHz clock.
v1 has only 16bits, so we only increase v2.
So we just exchange the timrot clock in imx28.
On imx23 we have timrotv1 and everything stays the same.
Signed-off-by: Torben Hohn <torbenh@linutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Regenerate the mxs_defconfig to match recent kernel using the following
commands:
make mxs_defconfig
make savedefconfig
cp defconfig arch/arm/configs/mxs_defconfig
Then enable these features:
- MTD block access
- UBI and UBIFS
- JFFS2
- EXT2 and EXT4
- AT24 EEPROM support
- Support for most of the SPI flashes
- Support for ethernet PHYs that are usually used on mxs designs
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Extend imx6q DEBUG_LL uart port selection support to cover all i.MX
SoCs. The 'range' of the Kconfig option gets dropped, as users
looking at the option must know the uart number on his board. The
bottom line is that the build system will report an error if an
invalid port number is picked for given SoC.
The header arch/arm/include/debug/imx-uart.h is created to accommodate
all the uart base addresses. And the header will also be used for
other low-level debug facility later.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It's improper to use combined symbol DEBUG_IMX31_IMX35_UART for
imx31 and imx35, because imx31 has 5 UARTs while imx35 only has 3.
So later when we add UART port selection for DEBUG_IMX31_IMX35_UART,
we will have problem.
Use separated Kconfig options for imx31 and imx35 debug uart selection.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
in question and other dts related changes, and will have them go via DT
branch to save the cross branch dependency.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRB24TAAoJEFBXWFqHsHzO3RcH/22Qe0+BUjxj1NBrBjBee6YE
ymb2CIOaTM2PgAQJZDgqGa4zgbPK7bcLu6fSyyg+XzExaxZ/CQI0EuKjMSroiyoB
6tRB76dz9ESWO4QYrQH65QxdY5Bi3VYDXv9+NeOdl0lzHR1wJp/Eeqvx608+aKIa
ps5Db1OdJn5TZ1o8Ye+/m4BUFBp+6feTx3fFfgXdes61eZskJLokURQz9zA6qiDw
s6YCBt1lNSNG/duZD3uFichDSPi/h+YFWwinI+deakRUDNUIs4n8ofToc99N6zWd
iKTbWX1cWOJpAYHKHS2lCaKF0saIpqCt7jhz/wmyXwDCrSSWsmwQSpxc5xmhFXU=
=LfVI
-----END PGP SIGNATURE-----
Merge tag 'imx-cleanup-3.9' into imx/soc
GPIO address space reservation during early platform initialization is
not needed anymore for Tosa. Remove the calls to gpiochip_reserve()
which is due to be removed.
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since header mach/regs-mem.h is used only into mach-s3c24xx/,
this patch moves the header file in local.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since header mach/regs-power.h is used only into mach-s3c24xx/,
this patch moves the header file in local.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since header mach/regs-s3c2412-mem.h is used only into mach-s3c24xx/,
this patch moves the header file in local.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
the fields must be null-terminated:
the caller may use it as null-terminted string, next.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch is for just moving plat-s3c24xx/*.c into mach-s3c24xx/, so
that we could remove plat-s3c24xx directory. But since the PLAT_S3C24XX
is used in drivers, the statement is not deleted and it will be sorted
out next time.
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Share the common irq code by simply defining a correct mapping declaration
for the s3c2443.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Previously the irq init used s3c24xx_init_irq and an additional
arch_initcall to add the cpu specific irqs.
To be able to simplyfy the irq init later, create a new function
s3c2443_init_irq, which then calls s3c24xx_init_irq but also adds
the cpu specific irqs.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Share the common irq code by simply defining a correct mapping declaration
for the s3c2416.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Previously the irq init used s3c24xx_init_irq and an additional
arch_initcall to add the cpu specific irqs.
To be able to simplyfy the irq init later, create a new function
s3c416_init_irq, which then calls s3c24xx_init_irq but also adds
the cpu specific irqs.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This gets rid of the use of static irq mappings there.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
With this the definition of s3c24xx_irq_syscore_ops can also move to
common.h from plat/pm.h and the definitions of s3c24xx_irq_suspend
and s3c24xx_irq_resume are also not necessary anymore in plat/pm.h
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Only alpha and sparc are unusual - they have ka_restorer in it.
And nobody needs that exposed to userland.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cubieboard has two LEDs available for use, a blue one (labeled LED1)
and a green one (labeled LED2).
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds support for SMP to mach-virt using the PSCI
infrastructure.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Add support for the smallest, dumbest possible platform, to be
used as a guest for KVM or other hypervisors.
It only mandates a GIC and architected timers. Fits nicely with
a multiplatform zImage. Uses very little silicon area.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
[will: fixed up conflicts with GIC move to drivers/irqchip/]
Signed-off-by: Will Deacon <will.deacon@arm.com>
policy->shared_type field was added only for SoCs with ACPI support:
commit 3b2d99429e
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Wed Dec 14 15:05:00 2005 -0500
P-state software coordination for ACPI core
http://bugzilla.kernel.org/show_bug.cgi?id=5737
Many non-ACPI systems are filling this field by mistake, which makes its usage
confusing. Lets clean it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
For multicore SoC's, with cores sharing clock line, we are required to set
policy->cpus and policy->related_cpus with mask of cpus.
With following patch, we need to set policy->cpus with mask of all possible cpus
and policy->related_cpus would be filled automatically by the cpufreq core.
commit 4948b355e90080cd5ec1e91189f65a01e4186ef2
Author: Viresh Kumar <viresh.kumar@linaro.org>
Date: Tue Jan 29 14:39:08 2013 +0000
cpufreq: Simplify cpufreq_add_dev()
Current Tegra driver fills only ->related_cpus and not ->cpus, which looks to be
incorrect. Lets fix it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Highbank processors depend on the external ECME to perform voltage
management based on a requested frequency. Communication between the
A9 cores and the ECME happens over the pl320 IPC channel.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The pl320 IPC allows for interprocessor communication between the
highbank A9 and the EnergyCore Management Engine. The pl320 implements
a straightforward mailbox protocol.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Move clk setup to twd_local_timer_common_register and rely on
twd_timer_rate being 0 to force calibration if there is no clock.
Remove common_setup_called as it is no longer needed.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The BeagleBone dev kit uses the built-in RTC module, so
it would be nice to have this built by default in the
omap2plus defconfig.
Signed-off-by: Mark Jackson <mpfj@newflow.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adds tps65910 PMIC, lis3lv02d accelerometer, tsl2550 ambient light sensor,
tmp275 temperature sensor, matrix keypad, gbio based leds and D_CAN drivers
support. These peripherals are present on AM33XX family of devices (EVM,
BeagleBone and EVMSK). One has to manually enable these support to use the
drivers, so this patch enables all the drivers in omap2plus_defconfig
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add needed platform data so that it's possible to use Retu and e.g. feed
Retu watchdog.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP framebuffer driver now uses the standard dma allocator
instead of the (now removed) omap specific vram allocator.
Enable the Contiguous Memory Allocator by default to allow large
dma memory buffers allocation.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Many OMAP3 based boards such as Beagle, Overo and IGEP use
the TFP410 DPI-to-DVI chip. So, it's good to have it built
as a module by default on OMAP2+ config.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IGEPv2 board has two user GPIO LEDs and one of them is
default to "on" to tell the user that the board booted correctly.
But to use these LEDs the config options CONFIG_LEDS_GPIO,
CONFIG_LEDS_TRIGGERS and CONFIG_LEDS_TRIGGER_DEFAULT_ON have to
be enabled.
Since only the default-on and default-off triggers were used
anyway, it is better to just use .default_state instead of
.default_trigger and not depend on CONFIG_LEDS_TRIGGER_*
Also, this is consistent with IGEPv2 Device Tree that uses
default-state instead of linux,default-trigger for the leds
device nodes. The LED names also have been updated to use the
same names used on omap3-igep0020.dtb.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch supports the TPS65910 PMU function on the AM3517 Craneboard.
The IRQ pin, SYS_NIRQ is dedicated connection between the AM3517 and
the TPS65910 PMU.
To handle the PMU IRQs, mux configuration is required.
Platform data configuration:
.IRQ number : SYS_NIRQ (M_IRQ_7)
.External clock source : external 32KHz clock is connected
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
