G-Link SPI Transport is used to communicate with external audio codec.
Add G-Link SPI Transport device to support that configuration.
CRs-Fixed: 1045916
Change-Id: I97ca857c21d8873574a180d289e2fbca29c8a891
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
GLink SPI Transport enables point-to-point communication with an
external subsystem that uses SPI bus to interface. This enables
multiplexing multiple logical channels over the SPI bus.
CRs-Fixed: 1045916
Change-Id: I1936bb0542bcd531726bf987ef806969ce96d498
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Currently the remote rx_intent is stored with the primary information.
The transport cannot provide a cookie to be retrieved and used later during
transmission.
Add support to receive a remote rx_intent with a cookie.
CRs-Fixed: 1045916
Change-Id: Id5f204647205b2fde9e5cb422a3ddc8cc4f3a5a0
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Format specifier %p can leak kernel addresses while not valuing the
kptr_restrict system settings. When kptr_restrict is set to (1), kernel
pointers printed using the %pK format specifier will be replaced with 0's.
So that %pK will not leak kernel pointers to unprivileged users.
So change the format specifier from %p to %pK.
Debugging Note : &pK prints only Zeros as address. if you need actual
address information, pls echo 0 to kptr_restrict.
$ echo 0 > /proc/sys/kernel/kptr_restrict
Change-Id: I0baf2be2d5a476e2e4267f20b99d0ddf5492469e
Signed-off-by: Mallikarjuna Reddy Amireddy <mamire@codeaurora.org>
ITE tech touch driver puts the controller to IDLE state in suspend
function through an i2c write into controller register space. But
due to multiple triggers of fb blank events, the suspend
function is called repeatatively without resume, and the driver
causes i2c nacks in suspend function while again putting the
controller is IDLE state. This keeps the QUP5 clock ON and XO shutdown
doesn't happen.
This change prevents the touch driver to execute the i2c write, to
put the controller in IDLE state, by repeatative fb blank events,
and causes XO shutdown to happen within time limits.
Change-Id: Ie3ee6b861c10ae901dea54f252f6a799d688f02a
Signed-off-by: Shantanu Jain <shjain@codeaurora.org>
ITE tech touch driver dynamically detects the controller attached
to the device in its probe. And if the driver fails to identify
the controller, it exits the probe with the error code. But in the
probe error path, it doesn't retain the error code, replace it
with zero and registers the device instead of failing.
This change corrects the probe error path of ITE tech touch driver
and makes sure it returns the error code if it fails.
Change-Id: I8f193ee10076b6cf058b0a6940db54f71f70b758
Signed-off-by: Shantanu Jain <shjain@codeaurora.org>
Add low reset gpio and delay reset support for ITE tech
driver.
ITE tech controller support low reset gpio configuration. This
property is parsed from the DT, and reset gpio is set to low.
Reset delay value is also parsed from DT which is required by the
ITE tech controller.
Change-Id: I314677747e8bbbcb273cd898376bbe03197c8c25
Signed-off-by: Shantanu Jain <shjain@codeaurora.org>
Do not put the ITE tech touchscreen driver in infinite
loop while probing.
Sometimes, when there is multiple touchscreen support on the
same snapdragon device, then the dynamic detection is used
to confirm which touchscreen is connected to the device.
So, this change will not make the CPUs to get hogged with
infinite loop of ITE tech driver.
Now it can easily get out of probe with error path releasing
the resources properly.
Change-Id: Ib9905017fc18999e7ab7c9cb8bc1af398f5f9791
Signed-off-by: Shantanu Jain <shjain@codeaurora.org>
WCD audio codecs contain SPI slave hardware module to provide access
to codec memory and SPI register space. Change adds driver for this
slave hardware. This driver uses regmap for SPI internal register
accesses and plugs in to standard SPI framework as child device to
master controller driver.
CRs-Fixed: 1049012
Change-Id: I0640ac1ed60a2ec3633636760593211ecd2f9c2d
Signed-off-by: Bhalchandra Gajare <gajare@codeaurora.org>
WCD audio codecs have DSP embedded to perform signal processing on
audio data. The codec driver has control over the DSP clock, power etc,
whereas the DSP memory can be accessed through an different bus slave
interface. In such cases, it is required to make sure the hardware
expected sequences are met for the DSP to function properly. The
wcd-dsp manager driver registers as master to component framework
and provides the ability to sequence the operations between the child
drivers. Upon registration of all children, the wcd-dsp manager driver
parses the wcd dsp image, downloads the image and boots up the DSP.
It invokes the component children to perform the tasks in sequence.
CRs-Fixed: 1049012
Change-Id: I059e1b111c607e49a7cc9a7940cf458e701c73d3
Signed-off-by: Bhalchandra Gajare <gajare@codeaurora.org>
wcd_dsp_utils adds utilities that will be used by the
wcd dsp manager driver. Add helper functions to parse
WDSP image and provide list of segments to be loaded
to memory.
CRs-Fixed: 1049012
Change-Id: I2b1464c2a035a039440e6d3e5122ad3f90da4d1e
Signed-off-by: Bhalchandra Gajare <gajare@codeaurora.org>
