During migrate_tasks, we have to drop the dead_rq lock in
order to preserve locking order when acquiring task->pi_lock.
This may allow the task to migrate off of dead_rq. Therefore,
don't attempt to migrate such a task again from dead_rq.
Change-Id: Id31b58e231d3dcd7d32e0dc7f264595d60a7c408
Signed-off-by: Vikram Mulukutla <markivx@codeaurora.org>
During atomic commit - validate failures, the newly allocated
pipes and pipes taken from the destroy list are cleaned up.
Currently pipe ndx is checked which can lead to cleaning up
the already in use multirect instead of the rect allocated
in the current validate. Add checks to include checking based
on multirect to avoid such cases.
Change-Id: I7f8fb6630314cdc523490e28d90dd3776bdfeada
Signed-off-by: Veera Sundaram Sankaran <veeras@codeaurora.org>
To improve accuracy update RRADC USBIN current
scaling factor for V/A from 0.5 to 0.53.
Change-Id: Ia13bd8702f337f71dae5d612f6efe55ee8c2a317
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
This reverts commit c93b93ee87 ("ARM: dts: msm: disable L1 and
L1ss for PCIe on msmcobalt").
Re-enable a necessary power saving feature for PCIe and its
client.
Change-Id: I231f518b701a988ab4a4f475e7e3c6f17d58187b
Signed-off-by: Tony Truong <truong@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Enabling L1 / L1SS for 11ad device causes PCIe
link down or PCIe NOC read/write timeouts.
To prevent that, disable L1 for 11ad devices after
PCIe enumeration and resume.
Change-Id: I5061c95855d462879c2f5237ded80131de4d215d
Signed-off-by: Maya Erez <merez@codeaurora.org>
Allow the mitigation clamp current values for the leds to be
configured through the device tree.
CRs-Fixed: 1060212
Change-Id: I23bf67fba7cef2735db436899a9d5b3306e5a77f
Signed-off-by: Devesh Jhunjhunwala <deveshj@codeaurora.org>
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
Currently multiple regulator devices can be specified for LED
switch device though a switch device may just require one supply.
Also, before the switch device is enabled, voltage request is
sent to set the maximum voltage. This is not needed with the
regulators like BoB being used as supply for the switch device.
Just enabling the regulator is enough during switch operation.
Modify the way the regulator is obtained and controlled for
switch operation.
Since BoB regulator is configured by the bootloader properly
for flash operation, remove them from the supply list of LED
switch devices on pmicobalt and pm2falcon.
While at it, fix the way device tree properties are read from
flash/torch, switch devices.
CRs-Fixed: 1083246
Change-Id: I8eb5f305f89bc18ad4b735bd89cbf259f0e1ea11
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
Add support to query max_current for each switch node through
sysfs. This will be useful to know the maximum current that
the flash switch device can draw at that time.
Change-Id: Ie83e71eafff5c49c81f56f92aa719662814997ed
Signed-off-by: Devesh Jhunjhunwala <deveshj@codeaurora.org>
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
The number of total glink tx buffers are running out
while exercising audio concurrency usecases. Increase
the max tx count to accommodate additional buffer needs.
Signed-off-by: Shiv Maliyappanahalli <smaliyap@codeaurora.org>
Change-Id: Iab64336f8efde2778c16156c6bfcf566c4c892d3
Following the introduction of the top-tasks approach towards frequency
guidance, the documentation on frequency guidance needs to be updated.
Update the same with new and accurate information.
Change-Id: If7deee97c09666b7d9513f79c0e278c430acfdfd
Signed-off-by: Syed Rameez Mustafa <rameezmustafa@codeaurora.org>
Add Audio and QCA slimbus instance entries.
Entries are disabled by default. Need to enable
along with slave instances.
Change-Id: I372e9e38a567e0cf83a226f29510fdf570decd43
Signed-off-by: Dilip Kota <dkota@codeaurora.org>
The new diag client requires additional memory from hlos.
This patch caters to diag memory requirement.
CRs-Fixed: 1079523
Change-Id: Ief14bb96bfdc1998b7b9423755daae8d93964672
Signed-off-by: Manoj Prabhu B <bmanoj@codeaurora.org>
Forcing a certain current limit is not supported in the current
driver, but well needed in when pd is active.
In this change, ICL_OVERRIDE/APSD and USB mode are updated, so
that PD can alter current limit by simply voting the ICL
setting.
Change-Id: I8d3ec938d433fe9bdbb8c091873c07e75c49d632
Signed-off-by: Harry Yang <harryy@codeaurora.org>
Do not dump PCIe PHY and PARF register space when there is
a linkdown. By the time PCIe receives the linkdown interrupt,
the reset for PCIe PHY has already happened, so these registers
do not have any meaningful value.
Change-Id: I8f66ab9375fd42573a895d5d872a3d2e1782adee
Signed-off-by: Tony Truong <truong@codeaurora.org>
xHC gets powered down when host mode is stopped. xHCI power
management is intended for ACPI based power management which
is defined for PC architecture. Hence there is no need to
clear run/stop bit and save the runtime register states upon
port suspend.
Change-Id: I9d0b31021e7c47084cd92c8c70e17cff3d057655
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Sink may issue attention event faster then it can be processed by
source. Create a list of attention events and process them one by
one in the order on workqueue to avoid missing any attention event
from sink.
Change-Id: I36fd45efe1aa9437d5551002fc75a5f37d9cef79
Signed-off-by: Ajay Singh Parmar <aparmar@codeaurora.org>
HDCP authentication requires valid keys on the source device.
If keys are not present, authentication can never be successful.
Check if the device is provisioned with hdcp keys, if so, proceed
with the hdcp authentication on HDMI/DisplayPort cable connection
otherwise avoid authentication as it may result in unnecessary
re-authentication loop.
Change-Id: I391ee35fa20cfade89773ecb565b220cc6249b8d
Signed-off-by: Ajay Singh Parmar <aparmar@codeaurora.org>
ARRAY_SIZE returns size of array. While sending command string
we need to only pass size of actual command string, hence use
strlen in place of ARRAY_SIZE.
Change-Id: If0afc6b1209b03ae17472a17b34d9d403757bfd0
Signed-off-by: Avaneesh Kumar Dwivedi <akdwived@codeaurora.org>
