MSM falcon supports 10-bit decode. This commit will
parse 10-bit entries from dtsi and will use
corresponding bus table based on session type.
Change-Id: I7e3655be5c3ea0800499cf24c05899f3d518bbd6
Signed-off-by: Deepak Kushwah <dkushwah@codeaurora.org>
CRs-Fixed: 1087798
Initial support for all BLSP I2Cs with default configuration
and disabled state such that clients can overwrite and enable
respective I2C instance as per need.
Change-Id: If08ff46e72d537254e90707f28c849a86f262853
Signed-off-by: Mukesh Kumar Savaliya <msavaliy@codeaurora.org>
Initial support for all BLSP UARTs with default configuration
and disabled state such that clients can overwrite and enable
respective UART instance as per need.
Change-Id: I15ef73049cee76c6ea5b3916d9281bbd9fdfc563
Signed-off-by: Mukesh Kumar Savaliya <msavaliy@codeaurora.org>
Remove the secure_camera ctrl_id unless the support is available
from the sde rotator driver. If this id is defined and functionality
is not present in the V4L2 driver it causes the rotator use cases
to fail.
CRs-Fixed: 1090525
Change-Id: I48c50bc320425c0db40cd4865e05c6b7a7fb5da3
Signed-off-by: Abhijit Kulkarni <kabhijit@codeaurora.org>
Few alpha PLLs would require to be able to slew in the same VCO mode, which
means the PLL would be able to update the new frequency L value without
turning it off. But to be support this feature the PLL needs to calibrated
at the mid of the VCO range and then enabled.
Change-Id: I24820bd6254002f8a8db9604d230dcbce59b1beb
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Some RCGSs could have sources with dynamic frequencies and fixed sources
where if the RCG has the flag of CLK_SET_RATE_PARENT set, it would try to
propagate the clock rate to the fixed source PLLs too. To identify sources
of the RCGs where the rate should propagate to parent PLL, add a member in
freq_tbl to represent source frequency. This would be used by the
_freq_tbl_determine_rate to set its parent frequency on the PLL.
Change-Id: I7f1c0d9d84607821893a1e5d17934dae5acef5f4
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Add the clock operation list_registers which would print the register
content of a clock. This is supported for PLL/RCG/Branch/Gate clocks.
Also add support for list_rate for the RCG clock which would list all the
frequencies/rates supported by the SW.
Change-Id: I3b4cf83e776750d993d53331142223109bf0862e
Signed-off-by: Taniya Das <tdas@codeaurora.org>
The clock api clock_debug_print_enabled would allow any client like low
power driver to print all the enabled clocks which include the
prepare_count/enable_count/rate/rate max vote.
Change-Id: I936496e553bc958c10e743fd8a225ffc7fbc0f79
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Add support for clocks debugfs to be able to display
- rates_max which indicates the frequency to voltage mapping of a clock.
- list_rates, the list of clock frequencies supported by root clocks.
- Also display the rate_max associated with enabled clocks list.
Change-Id: I0a202af6f46c7cf164036d65487db5c40aab4063
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Update clock debugfs to support the below functionalities.
- Allow enable/disable a clock.
- Allow set_rate on a clock.
- Display the list of enabled_clocks along with prepare_count,
enable_count and rate.
- Display the register contents of all the clocks which support
this clock operation.
Change-Id: Ib67b3a3409c9e7d8adb710bb524f54f543abf712
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Fix issues found during PD compliance testing for DisplayPort
downstream ports:
- The outgoing DP Status message must contain a single VDO. This
also fixes certain devices which would not respond unless there
was a status object included in the request. Initialize this to
0x1 to indicate that the DFP_D is connected.
- Don't send Enter Mode if the discovered mode doesn't support UFP_D.
- Don't send Configure if the Status response doesn't support UFP_D.
Change-Id: I690860613670753ae6634786f3ee2746a36be54a
Signed-off-by: Jack Pham <jackp@codeaurora.org>
If a client matching the SVID for an incoming SVDM is found,
assume it has handled the message completely and simply return.
This avoids the case when it handles an Attention message by
queuing another VDM request, only to have it inadvertently
deleted in the generic handling below.
But we also lose tracking of Discover/Enter/Exit Mode
exchanges though that was only used for informational purposes.
Change-Id: Ie23d473302d7fbda9b243a150e5c52d025007e4f
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Add clock of_idx entries for audio external clock registered
to the qcom clock framework.
Change-Id: Ie592d06d2e09c2e263a2e9485a42eafb368e49cc
Signed-off-by: Meng Wang <mwang@codeaurora.org>
vb2_queue_release uses mutex lock. So, the locks should be
destroyed at the end.
Change-Id: I8043a13d366fcb20a8a819c4739177258ad508ac
CRs-Fixed: 1086284
Signed-off-by: Karthikeyan Periasamy <kperiasa@codeaurora.org>
Due to a HW issue on the multimedia block on MSMCOBALT, the clock
sources or RCGs can end up running at XO frequency after a
multimedia power collapse. In order to avoid this issue, SDE rotator
as a multimedia clients need to call clk_set_rate() prior to
enabling its clocks.
CRs-Fixed: 1090358
Change-Id: Ib00b894f44a349fb3650df43f73f3599c09e46de
Signed-off-by: Benjamin Chan <bkchan@codeaurora.org>
There is currently a check to prevent backlight scaling when the backlight
level is below the minimum level. This min level and scale are both sent by
userspace. There should be no check in driver comparing backlight to min
level when doing scaling. That check will be done in user mode. The
driver should have the flexibility to do scaling in all scenarios.
CRs-Fixed: 1090387
Change-Id: I6b036db5169c89091ca452c68d6773d9df6d5e06
Signed-off-by: Benet Clark <benetc@codeaurora.org>
With syzkaller help, Marco Grassi found a bug in TCP stack,
crashing in tcp_collapse()
Root cause is that sk_filter() can truncate the incoming skb,
but TCP stack was not really expecting this to happen.
It probably was expecting a simple DROP or ACCEPT behavior.
We first need to make sure no part of TCP header could be removed.
Then we need to adjust TCP_SKB_CB(skb)->end_seq
Many thanks to syzkaller team and Marco for giving us a reproducer.
CRs-Fixed: 1089895
Change-Id: I84185558fa6e80b13d7d0078bda9d75143680941
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Marco Grassi <marco.gra@gmail.com>
Reported-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Git-commit: ac6e780070e30e4c35bd395acfe9191e6268bdd3
Git-repo: git://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git
[subashab@codeaurora.org: resolve trivial merge conflicts]
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Sockets can have a filter program attached that drops or trims
incoming packets based on the filter program return value.
Rose requires data packets to have at least ROSE_MIN_LEN bytes. It
verifies this on arrival in rose_route_frame and unconditionally pulls
the bytes in rose_recvmsg. The filter can trim packets to below this
value in-between, causing pull to fail, leaving the partial header at
the time of skb_copy_datagram_msg.
Place a lower bound on the size to which sk_filter may trim packets
by introducing sk_filter_trim_cap and call this for rose packets.
CRs-Fixed: 1089895
Change-Id: Idc52737bc96097a9220dfe47bb76e94ff1026a05
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Git-commit: f4979fcea7fd36d8e2f556abef86f80e0d5af1ba
Git-repo: git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git
[subashab@codeaurora.org: resolve trivial merge conflicts]
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Set the diag forward write buffers to busy state when glink
diag channel receives remote disconnected event.
Change-Id: I3c9422f3a790c0c1633ab64d4213a088faaeb9e5
Signed-off-by: Sreelakshmi Gownipalli <sgownipa@codeaurora.org>
Some smmu context banks are reserved for use by secure software. Do not
attempt to use the interrupts associated with those context banks.
Change-Id: I92e98ab46107fbcfd843898423b41716a204c2ae
Signed-off-by: Patrick Daly <pdaly@codeaurora.org>
Add support for compress capture in compress driver.
Add audio record support through compress driver.
CRs-fixed: 1072067
Change-Id: I7c6ab8bc0e88010eb221788cf8ce4c182e3128d9
Signed-off-by: Satish Babu Patakokila <sbpata@codeaurora.org>
PCIe MSI have to be contiguous by spec. Relocated
PCIe node so that it receives contiguous MSIs from
GIC driver.
Change-Id: Ia73ab1ba51df7b501d246bb45141018409496d01
Signed-off-by: Tony Truong <truong@codeaurora.org>
Add all SPIs for MSI, the base address, and the base SPI
to PCIe node to support and enable QGIC MSI on msmcobalt.
Change-Id: I1e74f1b03c3e15880efdac7ff07aca2f628de99d
Signed-off-by: Tony Truong <truong@codeaurora.org>
Add device tree support for msmcobalt interposer platform
for regulators of UFS.
Change-Id: I78d2c27743d30b90a96e3d8df60859f67db7ddb8
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
