Controller driver passes current speed to QUSB2 PHY driver in
the flags parameter. Determine linestate using speed,
mode and cable connection status. This deprecates the older
mechanism where linestate was determined by reading the now
obsoleted QUSB2PHY_PORT_UTMI_STATUS register.
Change-Id: I682eb250964f32f93d7b31dae0291aca7fa44362
Signed-off-by: Devdutt Patnaik <dpatnaik@codeaurora.org>
DP/DM linestate is needed by the QUSB2 PHY driver to configure the
polarity of DP/DM transition triggers for exiting low power mode.
This was previously available via the QUSB2PHY_PORT_UTMI_STATUS
PHY register which is now deprecated. In order to correctly determine
the interrupt polarity we need to pass the current operating speed
to the QUSB2 PHY driver. The PHY driver uses mode, speed and
cable connection status to determine the linestate and configure
interrupt polarities for wake up. Add logic to determine operating
speed for host and device mode cases.
Change-Id: Iaede1269f514a314bd9717a33100f748e7753b2a
Signed-off-by: Devdutt Patnaik <dpatnaik@codeaurora.org>
Update the device node for QUSB2 PHY with the recommended
register initialization sequence for host mode.
This is needed to fix HS enumeration issues due to port
reset failure.
Change-Id: I8cfed672ff02cd61beb956116f9fcd365211cf11
Signed-off-by: Devdutt Patnaik <dpatnaik@codeaurora.org>
Update QUSB2 HS PHY init sequence in host mode to fix
enumeration issues due to port reset operation failure.
Change-Id: I95daf3e3a833f9daeac6190daa33191f9db8cf26
Signed-off-by: Devdutt Patnaik <dpatnaik@codeaurora.org>
Modify FE ID check to use > instead of >= since
MSM_FRONTEND_DAI_MM_MAX_ID is defined as
MSM_FRONTEND_DAI_MULTIMEDIA16 which is a valid
FE ID.
Change-Id: I0ba4d62e3723841c3dfccdca210c80cd220f78f7
Signed-off-by: Ben Romberger <bromberg@codeaurora.org>
Adding the device tree files for RUMI platform.
Change-Id: I980e39b8c072fc2ec35d84b8698c40c770f7f041
Signed-off-by: Venkatesh Yadav Abbarapu <vabbar@codeaurora.org>
Layerwise bitrate with predefined distribution table is applied
if HP is enabled. This is wrong (since client may configure
custom distribution) and unnecessary (client may not configure
layerwise distribution and use cumulative).
CRs-Fixed: 1023504
Change-Id: I053587ae85b36ce0b08fdb5918c0f6b9d678dd24
Signed-off-by: Praveen Chavan <pchavan@codeaurora.org>
When unloading a TA, the operations to check ref_cnt,
scm_call to unload TA, free app list entry should be
within one critical section. Otherwise, if another
thread comes in and tries to load TA, TA status will
be out-of-sync. so move __qseecom_cleanup_app()
and __qseecom_reentrancy_check_if_no_app_blocked()
to the beginning of qseecom_unload_app(), as these
functions may release app_access mutex for a short
period.
Change-Id: I3e961f4fe1728a32314a3acf7af719374c90d01f
Signed-off-by: Zhen Kong <zkong@codeaurora.org>
LMH DCVSh will retain the mitigation till it clears the Low
threshold. With mitigation happening at 95C, configuring the
low threshold as 65C will hold the mitigation till it clears 65C,
which will impact the performance.
Instead of configuring the low threshold, configure the ARM threshold
from HLOS and low threshold will be configured 2C less than the
high threshold in the trust zone.
CRs-Fixed: 1024370
Change-Id: Ifb303d7266c98eb94c5eb6f806b7c5e1d95236d3
Signed-off-by: Ram Chandrasekar <rkumbako@codeaurora.org>
This corrects rotator irq enable mismatch by moving enable/disable
sequence to resource allocation/deallocation time. This will
eliminate race condition between regdma start and wait for done,
which causes unacknowledged rotator interrupt to continuosly trigger
MDSS main interrupt handler, ending in watchdog reset.
CRs-Fixed: 1035411
Change-Id: I597b58b478a35e9c3e3afb1a2ddd20ad87961c1a
Signed-off-by: Alan Kwong <akwong@codeaurora.org>
Providing additonal linear format support for v4l2 rotator in mdss 3.x
hardware.
CRs-Fixed: 1032294
Change-Id: Ie8a19341831d4ffaea36898a80c71ab25f5daf3c
Signed-off-by: Benjamin Chan <bkchan@codeaurora.org>
Add dts mpm2-sleep-counter node which is used by the boot_stats driver.
This dt node gives imem offset to read boot stats written by the
bootloader.
CRs-Fixed: 1037982
Change-Id: I4f8ec495ae02908d1d8cd7e86148a6d4bd38b198
Signed-off-by: Runmin Wang <runminw@codeaurora.org>
Some MFD PMIC configurations do not support interrupts. Make the interrupt
controller optional to support these PMIC configrations.
Without an interrupt controller this driver simply passes a regmap to
its children.
CRs-Fixed: 1037797
Change-Id: I52b909dd226494987c79ed106ffdf9892d966ef1
Signed-off-by: Nicholas Troast <ntroast@codeaurora.org>
Following the convention like MTP and CDP, create a separate dtsi file
for msmcobalt qrd platform.
CRs-Fixed: 1036660
Change-Id: I8ccbbc9ef0795397614ad0644fd1f2b5e31e3780
Signed-off-by: Runmin Wang <runminw@codeaurora.org>
Update MPM interrupt mapping to bypass some of the interrupts as per the
HW specification.
CRs-fixed: 1032455
Change-Id: I60c60470a649eecd5bacf0b39b20dff58c910897
Signed-off-by: Archana Sathyakumar <asathyak@codeaurora.org>
Configure the size of the default CMA region in DT.
Configuring the default CMA region in the DT is cleaner than using
CONFIG_CMA_SIZE_MBYTES since it is easier to configure per target
and the alloc ranges can be specified in DT.
CRs-Fixed: 1024204
Change-Id: I7d999382dcb6223d84424173a1726c250520ad04
Signed-off-by: Liam Mark <lmark@codeaurora.org>
Not all of the pIMEM Vault memory carveout is being used in msmcobalt.
Return unused portion of the pIMEM Vault carveout memory to HLOS.
CRs-Fixed: 1024170
Change-Id: Ie0cfab09192ca6b09ec4fe171aaf544e3fb5f08f
Signed-off-by: Liam Mark <lmark@codeaurora.org>
ISOC data transfer for audio device is offloaded to remote
usb audio driver entity. This requires remote entity to access
device context info, event ring, transfer rings and transfer
buffers allocated by APPS XHCI device. Hence add a platform
device which maps the XHCI device physical memory to virtual
memory and shares with remote processor's iommu. All the memory
info is then sent over QMI to remote entity.
Change-Id: I1abc80652a167cefa667b914b3a80a87326c3d44
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Upon usb audio device enumeration remote entity
communicates with usb audio qmi server to enable
or disable particular audio stream on usb audio
device. This off loades ISOC data transfer
operations to remote entity and allows APQ to go
to power collapse more frequently for better
power saving.
Change-Id: I2c9b0ba0837f8fec5c320e3117aa3b2f553db6b2
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
When continuous splash screen feature is enabled, the display needs to
be kept alive during the kernel boot up. Add proxy vote for all the
regulator supplies needed to keep the display panel alive over the DSI
interface until the display driver hand off can be executed.
CRs-Fixed: 1037857
Change-Id: I95544aaf607887ae34eace8a9b1f18a1375c5c6d
Signed-off-by: Aravind Venkateswaran <aravindh@codeaurora.org>
Add support for the DP link and crypto clocks on MSMCOBALT.
CRs-Fixed: 1028725
Change-Id: I6cdb366499f9589dff9a42491c7ff357e98d65c5
Signed-off-by: Deepak Katragadda <dkatraga@codeaurora.org>
The flash-led switch node must vote on the pmicobalt BoB
regulator. Hence, add this regulator node to that.
CRs-Fixed: 1024187
Change-Id: Ic4ec03e4fd545d44118c2225a3f8e26901ca1d81
Signed-off-by: Devesh Jhunjhunwala <deveshj@codeaurora.org>
Add support to control regulators required for
flash-led. The pmicobalt_bob regulator is one
such regulator required by the flash-led device.
CRs-Fixed: 1024187
Change-Id: I1515fba2fb04c0b4d21828af3cea6d322262ab14
Signed-off-by: Devesh Jhunjhunwala <deveshj@codeaurora.org>
Flash LED is a high energy aggregator from system as it is capable
to provide current up to 3750mA for illumination. Therefore, it
should be used with caution especially when battery state of charge
is low. Therefore, add a function which can be used by clients like
camera to query the flash current limit before using flash LED. This
protects the system from a possible UVLO condition.
CRs-Fixed: 964855
Change-Id: I17fa4f28cc151e3a3ad89d284995a3fa770bec68
Signed-off-by: Chun Zhang <chunz@codeaurora.org>
Signed-off-by: Devesh Jhunjhunwala <deveshj@codeaurora.org>
Flash LED module supports various kinds of strobe support. Strobe
type can be hardware or software, active high or low, and level or
edge trigger. Add support for configuring strobe type through
device tree properties.
CRs-Fixed: 1024187
Change-Id: Ief6a610c82b7f645966c596f543a1d30f7a40dcc
Signed-off-by: Chun Zhang <chunz@codeaurora.org>
Signed-off-by: Devesh Jhunjhunwala <deveshj@codeaurora.org>
During SSR(subsystem restart), add a delay when ADSP state
is not yet ready. This will avoid excessive logging when
ADSP state is not ready.
Change-Id: I7e127d97cdd22409d4e70788a7cf2013593d3bfe
Signed-off-by: Shiv Maliyappanahalli <smaliyap@codeaurora.org>
It is possible that core service can register with APR in
different contexts and may result in apr_register returning
EALREADY error while core service gets a NULL handle.
Avoid the race condition by holding command lock to ensure
that apr_handle does not get overwritten.
Change-Id: I8863185651fde8d29b5b8d8f183544bf0f215dbe
Signed-off-by: Shiv Maliyappanahalli <smaliyap@codeaurora.org>
Increase the maximum video buffers to 64 as with camera 64
buffers are allocated and used.
CRs-Fixed: 1039456
Change-Id: I37d91c4f7e5d98333cf6be3c75168e134ae78060
Signed-off-by: Shubhraprakash Das <sadas@codeaurora.org>
With smmu enabling, ipa3_pre_init is actually
probed twice and causing the crash, the fix
is to do only once.
Change-Id: I20bd718c8cb70029c4dd46c52dbece326b90ef80
Signed-off-by: Skylar Chang <chiaweic@codeaurora.org>
After sub system restart, opening glink channel while
lpass transport is not up results in failure and returns
error pointer. APR glink client although returns error for
the first glink command, does not set the apr handle to NULL
and incorrectly assumes err pointer as a valid handle when
opening the channel again.
Fix this by updating the apr handle to NULL when glink_open()
fails.
Change-Id: I53a219b1ebed5bc3593d500d80d580aac6431ab5
Signed-off-by: Shiv Maliyappanahalli <smaliyap@codeaurora.org>
Compare ion handles in driver instead of matching fds
to check if a buffer is already mapped or not.
Bug: 28747768
CRs-Fixed: 1026885
Change-Id: Ifd18d8689351c4a6a22c988d359fb413be19e142
Signed-off-by: Ashray Kulkarni <ashrayk@codeaurora.org>
Signed-off-by: Praveen Chavan <pchavan@codeaurora.org>
Signed-off-by: Deva Ramasubramanian <dramasub@codeaurora.org>
Signed-off-by: Arun Menon <avmenon@codeaurora.org>
Signed-off-by: Abdulla Anam <abdullahanam@codeaurora.org>
Signed-off-by: Amit Shekhar <ashekhar@codeaurora.org>
userptr may or may not be a null-value. Checking for this field
to qualify a plane as extradata has no merit. Ignore that check.
Bug: 28747768
CRs-Fixed: 1026885
Change-Id: I08d85ef462f09003aaa17f6ebc5d27de7083796f
Signed-off-by: Praveen Chavan <pchavan@codeaurora.org>
Signed-off-by: Praneeth Paladugu <ppaladug@codeaurora.org>
Signed-off-by: Amit Shekhar <ashekhar@codeaurora.org>
Initialize return values to their default before being
used.
Change-Id: Ie4dd908657573e5110bce65931d5507125da4c40
Signed-off-by: Shiraz Hashim <shashim@codeaurora.org>
Return error on data allocation failure to prevent use
after free case.
Change-Id: I9d173756e277c9006220c02c209309167f179609
Signed-off-by: Shiraz Hashim <shashim@codeaurora.org>
Add HDMI audio back end and associated apis to
configure channel, format and sample rate to
enable audio over HDMI.
Change-Id: Ieef8a2658f9730a9268041ac93ea3958489f2eae
Signed-off-by: Shiv Maliyappanahalli <smaliyap@codeaurora.org>
Add device tree entries to enable audio
over HDMI.
Change-Id: Ie9bb609f9681580d90e5ec35b89e587758c272d4
Signed-off-by: Shiv Maliyappanahalli <smaliyap@codeaurora.org>
In wil_p2p_listen chan is checked to protect against NULL
pointer access only before setting channel = chan->hw_value.
Add a global parameter check to cover all accesses to chan.
Change-Id: Ib975c99b3b87998c357251a37f4862cbbf68697d
CRs-Fixed: 1026286
Signed-off-by: Maya Erez <merez@codeaurora.org>
Add a module parameter alt_ifname that when set, will name
the primary network interface wigig<N> instead of the default
wlan<N>. This helps platforms such as android where we need to
clearly separate the WIGIG interface from the default wireless
interface.
Change-Id: Ie1cd3ccf777e84665075bc3b6d9fffa7d897de49
CRs-Fixed: 982931
Signed-off-by: Hamad Kadmany <hkadmany@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Parsing of audio routing in ASoC core has been changed in
kernel 4.4 to use new variables. Update the codec driver
to traverse to source dapm widget using new variables.
Change-Id: I8c545248f23c73ff9fb470705f1c17175a8e4e0b
Signed-off-by: Sudheer Papothi <spapothi@codeaurora.org>
During SSR, wcd9xxx_res irq lock is destroyed as part of resource
cleanup. If driver tries to access wcd9xxx_res irq lock before it's
initialized, it could cause crash. Check if wcd9xxx_res irq is 0
before using it to avoid crash.
CRs-Fixed: 1003482
Change-Id: I959caf7b305e965b84e8204168194bbfda72dc52
Signed-off-by: Meng Wang <mwang@codeaurora.org>
Add RGB LEDs that are present on pmicobalt. These LEDs are used
for applications like notification of charging indicator and
other user defined applications.
Since LPG channels 3,4 and 5 are assigned for Blue, Green and
Red LEDs on pmicobalt, keep them enabled in device tree.
CRs-Fixed: 1037821
Change-Id: I1a40bbe46e689d8c98f31cfef3a6743856288127
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
Export arch_get_cpu_efficiency API since it can be called
by the modules. Update topology header file too.
CRs-Fixed: 1038542
Change-Id: Ie2ab84b02a8fb4070a0e86f09f52db9aa4163003
Signed-off-by: Trilok Soni <tsoni@codeaurora.org>
The mask and enable values being used are incorrect for the
safety timer. Fix it. Also take this opportunity to update
all relevant macros to use the GENMASK(h,l)/BIT(x) macros.
CRs-Fixed: 1024187
Change-Id: Ibdd139c98aa289f1d6b8545b953e79a1187284e9
Signed-off-by: Devesh Jhunjhunwala <deveshj@codeaurora.org>
Add the qcom,current-ma property which is used to specify the
default current value to be used for the flash and torch devices.
This property is used by clients of the flash device.
CRs-Fixed: 1024187
Change-Id: I3670eaa65efc9d1efb29fb30500fb9067885b446
Signed-off-by: Devesh Jhunjhunwala <deveshj@codeaurora.org>
