This patch is used to remove the stack information
log in case of sdhci exception.
Change-Id: I5e3a56515f4bde092f81739ea22be2d1cdf74d4d
Signed-off-by: Zhou Li <clizhou@codeaurora.org>
Fix UAF where two threads can open and close the same file. Second
open will cause the private data for the first file to be overwritten.
When the first file is closed and the private data is freed, this makes
the now-shared private data OOB for the second thread.
CRs-Fixed: 1109763
Change-Id: I1c4618d5be99e140abf0f3ea0d7f485897db5ab2
Signed-off-by: Ankit Sharma <ansharma@codeaurora.org>
Signed-off-by: Anirudh Ghayal <aghayal@codeaurora.org>
If device is boot up by rtc alarm, the alarm irq will still be
enabled and the alarm time is smaller than current rtc time before
any alarm is set or canceled. If device is powered off now, it will
boot up automatically as the alarm irq is enabled.
So disable alarm irq if alarm is enabled and alarm time is in the
past.
CRs-Fixed: 2109666
Change-Id: Ie60bd1222a400cd45a6c5a385faa70190fbe7e3c
Signed-off-by: Mao Jinlong <jinlmao@codeaurora.org>
Refactor device tree to support multiple targets on virtual platform.
Change-Id: Id4a3519afd63b77510d824979fc71309ff6ac481
Signed-off-by: Zhiqiang Tu <ztu@codeaurora.org>
During SSR, down vote transport of xprt is not called.
This leads to transport not being able to go to idle state.
Downvote of transport is called in SSR path.
CRs-Fixed: 2131780
Change-Id: Ic374073187aab95b700aa3f795787819f34d3c3c
Signed-off-by: Dhoat Harpal <hdhoat@codeaurora.org>
Enable USB video class for USB camera support on
msm8996-auto devices
Change-Id: I2a385cf4c935d5bc2a4c1171f185baf30322ed1d
Signed-off-by: vpalvai <vpalvai@codeaurora.org>
The wled driver is not statically handling interrupt flags.
Pass proper flag such as IRQ_TYPE_EDGE_RISING for wled
"sc-irq" interrupt through device node.
Change-Id: I90974bd7995949a97bb7070e86c469cde646096a
Signed-off-by: Tirupathi Reddy <tirupath@codeaurora.org>
CAN socket SELinux support is required to be able
to distinguish between generic socket and can_socket
Change-Id: I9ec2099fc4c08ab6406e33ff9ad821ef18261763
Signed-off-by: Alex Yakavenka <ayakav@codeaurora.org>
Reset the HDR capabilities during the bridge disable.
The capabilities are re-programmed the next time
the userspace issues the call to populate the modes.
Change-Id: I04dbaa99c291de13b81e12cb9742cc97d9b02593
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Currently, IBB PWRUP_DLY1 and PWRDN_DLY2 settings are configured
only for values greater than 0. However, 0 ms (no delay) can be
allowed by disabling EN_PWRUP_DLY1 or EN_PWRDN_DLY2 bits. Add
support to allow this configuration.
CRs-Fixed: 2125062
Change-Id: I8ef3b5522b8d4db6befb3fb1c2e58ea24c0f5ea0
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
PMI8998 LAB pulse skip configuration is different from PMI8996
and earlier PMICs. Fix it by using the right configuration API
to configure LAB PS_CTL along with supporting PM660A properly.
Since the existing LAB PS configuration threshold for pmi8998 is
incorrect in device tree, update it along with this change.
Change-Id: I2686733867ec3e2909d0c071a5881d3d824c713e
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
If CABC is enabled and auto calibration is attempted, then OVP
fault can be seen even with a valid sink configuration and a
brightness level greater than or equal to 0.4 % dimming. This is
because of the modulation done through CABC pin which if low
enough can cause the brightness level to still go further down.
Fix this by disabling CABC on all sinks before running auto
calibration and re-enable it if the feature is enabled. Also,
modify the auto calibration brightness level to 200 so that the
load increase on WLED_VOUT can bring the voltage below OVP
threshold quick enough on a valid sink configuration.
Finally, disable WLED module before switching the sink
configuration and enable it after configuring sinks.
CRs-Fixed: 2125217
Change-Id: I570dc9eba540cd96328afd7c68f4643a112c4962
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
Pass NULL pointer to of_get_address_byname() for size and flags
parameters instead of an integer value 0.
Change-Id: I53984141bb8f1164c27b6a9a5d90853b4d077ee1
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
If the OVP fault is present during boot-up run
a WLED string auto-calibration.
Change-Id: I4b0e85cd64a1e8bca9bc7de17521d1f83798ed12
Signed-off-by: Anirudh Ghayal <aghayal@codeaurora.org>
Export msm_ipc.h for use by user-space.
Change-Id: I53b96c4cb0b6fe785d3e73e7f00565c68dadf411
CRs-Fixed: 2125734
Acked-by: Jennifer L Zenner <jzenner@qti.qualcomm.com>
Signed-off-by: Yasir Malik <ymalik@codeaurora.org>
Add configuration for 64-bit FSM platforms.
Change-Id: Icd5fb7875674e537a102af3fbc7d7c8b90c59740
CRs-Fixed: 2125734
Acked-by: Jennifer L Zenner <jzenner@qti.qualcomm.com>
Signed-off-by: Yasir Malik <ymalik@codeaurora.org>
HL1.0 has more number of descriptors and hence we can
queue more packets for tx.
Allow a higher number of tx pending packets for better
throughput in concurrency cases.
CRs-Fixed: 2104072
Change-Id: I8dd98cee04200fbeccf655dcb1d982d037077101
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
