Currently the build for a single-core (e.g. user-mode) Linux is broken
and this configuration is required (at least) to run some network tests.
The main issues for the current code support on single-core systems are:
1. {se,rq}::sched_avg is not available nor maintained for !SMP systems
This means that load and utilisation signals are NOT available in single
core systems. All the EAS code depends on these signals.
2. sched_group_energy is also SMP dependant. Again this means that all the
EAS setup and preparation code (energyn model initialization) has to be
properly guarded/disabled for !SMP systems.
3. SchedFreq depends on utilization signal, which is not available on
!SMP systems.
4. SchedTune is useless on unicore systems if SchedFreq is not available.
5. WALT machinery is not required on single-core systems.
This patch addresses all these issues by enforcing some constraints for
single-core systems:
a) WALT, SchedTune and SchedTune are now dependant on SMP
b) The default governor for !SMP systems is INTERACTIVE
c) The energy model initialisation/build functions are
d) Other minor code re-arrangements and CONFIG_SMP guarding to enable
single core builds.
Signed-off-by: Patrick Bellasi <patrick.bellasi@arm.com>
Scheduler-driven CPU frequency selection hopes to exploit both
per-task and global information in the scheduler to improve frequency
selection policy, achieving lower power consumption, improved
responsiveness/performance, and less reliance on heuristics and
tunables. For further discussion on the motivation of this integration
see [0].
This patch implements a shim layer between the Linux scheduler and the
cpufreq subsystem. The interface accepts capacity requests from the
CFS, RT and deadline sched classes. The requests from each sched class
are summed on each CPU with a margin applied to the CFS and RT
capacity requests to provide some headroom. Deadline requests are
expected to be precise enough given their nature to not require
headroom. The maximum total capacity request for a CPU in a frequency
domain drives the requested frequency for that domain.
Policy is determined by both the sched classes and this shim layer.
Note that this algorithm is event-driven. There is no polling loop to
check cpu idle time nor any other method which is unsynchronized with
the scheduler, aside from a throttling mechanism to ensure frequency
changes are not attempted faster than the hardware can accommodate them.
Thanks to Juri Lelli <juri.lelli@arm.com> for contributing design ideas,
code and test results, and to Ricky Liang <jcliang@chromium.org>
for initialization and static key inc/dec fixes.
[0] http://article.gmane.org/gmane.linux.kernel/1499836
[smuckle@linaro.org: various additions and fixes, revised commit text]
CC: Ricky Liang <jcliang@chromium.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Signed-off-by: Steve Muckle <smuckle@linaro.org>
Few Android drivers e.g. uid_cputime and PPPoLAC/oPNS,
keyreset/combo, cpufreq_interactive etc.. fail to build
as kernel modules. Instead of fixing the build lets
make these drivers non-modular (switch config to "bool"
from "tristate" in Kconfig) since Android doesn't
support building kernel modules anyway.
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
This governor is designed for latency-sensitive workloads, such as
interactive user interfaces. The interactive governor aims to be
significantly more responsive to ramp CPU quickly up when CPU-intensive
activity begins.
Existing governors sample CPU load at a particular rate, typically
every X ms. This can lead to under-powering UI threads for the period of
time during which the user begins interacting with a previously-idle system
until the next sample period happens.
The 'interactive' governor uses a different approach. Instead of sampling
the CPU at a specified rate, the governor will check whether to scale the
CPU frequency up soon after coming out of idle. When the CPU comes out of
idle, a timer is configured to fire within 1-2 ticks. If the CPU is very
busy from exiting idle to when the timer fires then we assume the CPU is
underpowered and ramp to MAX speed.
If the CPU was not sufficiently busy to immediately ramp to MAX speed, then
the governor evaluates the CPU load since the last speed adjustment,
choosing the highest value between that longer-term load or the short-term
load since idle exit to determine the CPU speed to ramp to.
A realtime thread is used for scaling up, giving the remaining tasks the
CPU performance benefit, unlike existing governors which are more likely to
schedule rampup work to occur after your performance starved tasks have
completed.
The tuneables for this governor are:
/sys/devices/system/cpu/cpufreq/interactive/min_sample_time:
The minimum amount of time to spend at the current frequency before
ramping down. This is to ensure that the governor has seen enough
historic CPU load data to determine the appropriate workload.
Default is 80000 uS.
/sys/devices/system/cpu/cpufreq/interactive/go_maxspeed_load
The CPU load at which to ramp to max speed. Default is 85.
Change-Id: Ib2b362607c62f7c56d35f44a9ef3280f98c17585
Signed-off-by: Mike Chan <mike@android.com>
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Bug: 3152864
This driver works on all QorIQ platforms which include
ARM-based cores and PPC-based cores.
Rename it in order to represent better.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
SRCU is not necessary to be compiled by default in all cases. For tinification
efforts not compiling SRCU unless necessary is desirable.
The current patch tries to make compiling SRCU optional by introducing a new
Kconfig option CONFIG_SRCU which is selected when any of the components making
use of SRCU are selected.
If we do not select CONFIG_SRCU, srcu.o will not be compiled at all.
text data bss dec hex filename
2007 0 0 2007 7d7 kernel/rcu/srcu.o
Size of arch/powerpc/boot/zImage changes from
text data bss dec hex filename
831552 64180 23944 919676 e087c arch/powerpc/boot/zImage : before
829504 64180 23952 917636 e0084 arch/powerpc/boot/zImage : after
so the savings are about ~2000 bytes.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
CC: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
CC: Josh Triplett <josh@joshtriplett.org>
CC: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
[ paulmck: resolve conflict due to removal of arch/ia64/kvm/Kconfig. ]
CPUFreq driver's Kconfig entries are added in Kconfig.<arch> files and they are
all included from the main Kconfig file using a menu entry. This creates another
level of (unnecessary) hierarchy within the menuconfig entries.
The problem occurs when there are drivers usable across architectures. Either
their config entry is duplicated in all the supported architectures or is put
into the main Kconfig entry. With the later one, we have menuconfig entries for
drivers at two levels then.
Fix these issues by getting rid of another level of menuconfig hierarchy and
populate all drivers within the main cpufreq menu. To clearly distinguish where
the drivers start from, also add a comment that will appear in menuconfig.
Reported-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Suggested-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds cpufreq driver for Loongson1B which
is capable of changing the CPU frequency dynamically.
Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The intel_pstate driver only supports the performance and the powersave
governors. With the performance governor ensuring the highest possible
performance settings, userspace tools fail to make any lasting changes.
In order to allow userspace tools to make modifications to the settings,
the powersave governor must be in use. This makes having the powersave
governor as the default convenient for systems where the intel_pstate
driver is being employed. Having to enable expert mode in the kernel
configuration is just a headache for such a trivial task.
This patch applies to all kernel versions 2.6.38 or greater after the
migration from CONFIG_EMBEDDED to CONFIG_EXPERT (6a108a14fa). Most
importantly, this applies to kernel versions 3.9 or greater when the
intel_pstate driver was introduced.
Signed-off-by: James Geboski <jgeboski@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The naming convention of this driver was always under the scanner, people
complained that it should have a more generic name than cpu0, as it manages all
CPUs that are sharing clock lines.
Also, in future it will be modified to support any number of clusters with
separate clock/voltage lines.
Lets rename it to 'cpufreq_dt' from 'cpufreq_cpu0'.
Tested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
5fbfbcd3e8 ("cpufreq: cpufreq-cpu0: remove dependency on THERMAL and
REGULATOR") was a little too quick in completely removing the dependency
on the THERMAL driver.
The problem is that while there are inline wrappers to turn the thermal
API calls into empty functions, those do not help if the cpu-thermal
driver is a loadable module and cpufreq-cpu0 is builtin.
Since CONFIG_CPU_THERMAL is a bool option that decides whether the cpu
code is built into the thermal module or not, we have to use a dependency
on the thermal driver itself. However, if CPU_THERMAL is disabled, we
don't need the dependency, hence the strange '!CPU_THERMAL || THERMAL'
construct.
Fixes: 5fbfbcd3e8 ("cpufreq: cpufreq-cpu0: remove dependency on THERMAL and REGULATOR")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq-cpu0 uses thermal framework to register a cooling device, but doesn't
depend on it as there are dummy calls provided by thermal layer when
CONFIG_THERMAL=n. And when these calls fail, the driver is still usable.
Similar explanation is valid for regulators as well. We do have dummy calls
available for regulator APIs and the driver can work even when those calls
fail.
So, we don't really need to mention thermal and regulators as a dependency for
cpufreq-cpu0 in Kconfig as platforms without support for thermal/regulator can
also use this driver. Remove this dependency.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Enable cpufreq and power kconfig menus on arm64 along with arm cpufreq
drivers. The power menu is needed for OPP support. At least on Calxeda
systems, the same cpufreq driver is used for arm and arm64 based
systems.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Pull thermal management updates from Zhang Rui:
"This time, the biggest change is the work of representing hardware
thermal properties in device tree infrastructure.
This work includes the introduction of a device tree bindings for
describing the hardware thermal behavior and limits, and also a parser
to read and interpret the data, and build thermal zones and thermal
binding parameters. It also contains three examples on how to use the
new representation on sensor devices, using three different drivers to
accomplish it. One driver is in thermal subsystem, the TI SoC
thermal, and the other two drivers are in hwmon subsystem.
Actually, this would be the first step of the complete work because we
still need to check other potential drivers to be converted and then
validate the proposed API. But the reason why I include it in this
pull request is that, first, this change does not hurt any others
without using this approach, second, the principle and concept of this
change would not break after converting the remaining drivers. BTW,
as you can see, there are several points in this change that do not
belong to thermal subsystem. Because it has been suggested by Guenter
R that in such cases, it is recommended to send the complete series
via one single subsystem.
Specifics:
- representing hardware thermal properties in device tree
infrastructure
- fix a regression that the imx thermal driver breaks system suspend.
- introduce ACPI INT3403 thermal driver to retrieve temperature data
from the INT3403 ACPI device object present on some systems.
- introduce debug statement for thermal core and step_wise governor.
- assorted fixes and cleanups for thermal core, cpu cooling, exynos
thrmal, intel powerclamp and imx thermal driver"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (34 commits)
thermal: remove const flag from .ops of imx thermal
Thermal: update thermal zone device after setting emul_temp
intel_powerclamp: Fix cstate counter detection.
thermal: imx: add necessary clk operation
Thermal cpu cooling: return error if no valid cpu frequency entry
thermal: fix cpu_cooling max_level behavior
thermal: rcar-thermal: Enable driver compilation with COMPILE_TEST
thermal: debug: add debug statement for core and step_wise
thermal: imx_thermal: add module device table
drivers: thermal: Mark function as static in x86_pkg_temp_thermal.c
thermal:samsung: fix compilation warning
thermal: imx: correct suspend/resume flow
thermal: exynos: fix error return code
Thermal: ACPI INT3403 thermal driver
MAINTAINERS: add thermal bindings entry in thermal domain
arm: dts: make OMAP4460 bandgap node to belong to OCP
arm: dts: make OMAP443x bandgap node to belong to OCP
arm: dts: add cooling properties on omap5 cpu node
arm: dts: add omap5 thermal data
arm: dts: add omap5 CORE thermal data
...
Add CONFIG_CPU_FREQ_BOOST_SW Kconfig option such that software-managed
boost is enabled only after selecting "EXYNOS Frequency Overclocking -
Software". It also depends on the thermal subsystem to be compiled in,
which is necessary for disabling boost and cooling down the device when
overheating is detected.
Software-managed boost _MUST_ _NOT_ be enabled without thermal subsystem
with properly defined overheating temperature thresholds.
This option doesn't affect the x86's hardware-driven boost support
in the acpi-cpufreq driver.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[rjw: Subject and changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
PM_OPP is a helper library used by several of the existing cpufreq drivers.
Some of the drivers select this symbol while others depend on it and rely
on the architecture to enable it. Make this behaviour more consistent and
obvious by having all the drivers select the symbol. This will also allow
better build coverage of the affected drivers.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch changes the cpufreq-cpu0 driver to consider if
a cpu needs cooling (with cpufreq). In case the cooling is needed,
the cpu0 device tree node needs to be properly configured
with cooling device properties.
In case these properties are present,, the driver will
load a cpufreq cooling device in the system. The cpufreq-cpu0
driver is not interested in determining how the system should
be using the cooling device. The driver is responsible
only of loading the cooling device.
Describing how the cooling device will be used can be
accomplished by setting up a thermal zone that references
and is composed by the cpufreq cooling device.
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: cpufreq@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
CONFIG_CPU_FREQ_TABLE will be always enabled when cpufreq framework is used, as
cpufreq core depends on it. So, we don't need this CONFIG option anymore as it
is not configurable. Remove CONFIG_CPU_FREQ_TABLE and update its users.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many CPUFreq drivers for SMP system (where all cores share same clock lines), do
similar stuff in their ->init() part.
This patch creates a generic routine in cpufreq core which can be used by these
so that we can remove some redundant code.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Kconfig dependecies for ARM SA11xx drivers are incorrect, so fix
them.
[rjw: Changelog]
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch moves cpufreq driver of SPARC architecture to drivers/cpufreq.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch moves cpufreq driver of SUPERH architecture to drivers/cpufreq.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch moves cpufreq driver of MIPS architecture to drivers/cpufreq.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch moves cpufreq driver of IA64 architecture to drivers/cpufreq.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch moves cpufreq driver of AVR32 based at32ap platform to
drivers/cpufreq.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As multiplatform build is being adopted by more and more ARM platforms,
initcall function should be used very carefully. For example, when
GENERIC_CPUFREQ_CPU0 is built in the kernel, cpu0_cpufreq_driver_init()
will be called on all the platforms to initialize cpufreq-cpu0 driver.
To eliminate this undesired the effect, the patch changes cpufreq-cpu0
driver to have it instantiated as a platform_driver. Then it will only
run on platforms that create the platform_device "cpufreq-cpu0".
Along with the change, it also changes cpu_dev to be &pdev->dev,
so that managed functions can start working, and module build gets
supported too.
The highbank-cpufreq driver is also updated accordingly to adapt the
changes on cpufreq-cpu0.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since commit 2aacdff entitled "cpufreq: Move common part from governors
to separate file", whenever the drivers that depend on this new file
(cpufreq_ondemand or cpufreq_conservative) are built as modules, a new
module named cpufreq_governor is created because the Makefile includes
cpufreq_governor.o twice. As drivers/cpufreq/cpufreq_governor.c contains no
MODULE directives, the resulting module has no license specified, which
results in logging of a "module license 'unspecified' taints kernel". In
addition, a number of globals are exported GPL only, and are therefore
not available. This fix establishes a new boolean configuration variable
that forces cpufreq_governor.o to be linked into the kernel whenever
either cpufreq_ondemand or cpufreq_conservative is selected.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It adds a generic cpufreq driver for CPU0 frequency management based on
clk, regulator, OPP and device tree support. It can support both
uniprocessor (UP) and those symmetric multiprocessor (SMP) systems which
share clock and voltage across all CPUs.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (99 commits)
drivers/virt: add missing linux/interrupt.h to fsl_hypervisor.c
powerpc/85xx: fix mpic configuration in CAMP mode
powerpc: Copy back TIF flags on return from softirq stack
powerpc/64: Make server perfmon only built on ppc64 server devices
powerpc/pseries: Fix hvc_vio.c build due to recent changes
powerpc: Exporting boot_cpuid_phys
powerpc: Add CFAR to oops output
hvc_console: Add kdb support
powerpc/pseries: Fix hvterm_raw_get_chars to accept < 16 chars, fixing xmon
powerpc/irq: Quieten irq mapping printks
powerpc: Enable lockup and hung task detectors in pseries and ppc64 defeconfigs
powerpc: Add mpt2sas driver to pseries and ppc64 defconfig
powerpc: Disable IRQs off tracer in ppc64 defconfig
powerpc: Sync pseries and ppc64 defconfigs
powerpc/pseries/hvconsole: Fix dropped console output
hvc_console: Improve tty/console put_chars handling
powerpc/kdump: Fix timeout in crash_kexec_wait_realmode
powerpc/mm: Fix output of total_ram.
powerpc/cpufreq: Add cpufreq driver for Momentum Maple boards
powerpc: Correct annotations of pmu registration functions
...
Fix up trivial Kconfig/Makefile conflicts in arch/powerpc, drivers, and
drivers/cpufreq
Add simple cpufreq driver for Maple-based boards (ppc970fx evaluation
kit and others). Driver is based on a cpufreq driver for 64-bit powermac
boxes with all pmac-dependant features removed and simple cleanup
applied.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
According to discussion of the ARM arch subsystem migration,
ARM cpufreq drivers move to drivers/cpufreq. So this patch
adds Kconfig.arm for ARM like x86 and adds Samsung S5PV210
and EXYNOS4210 cpufreq driver compile in there.
As a note, otherw will be moved.
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
With dynamic debug having gained the capability to report debug messages
also during the boot process, it offers a far superior interface for
debug messages than the custom cpufreq infrastructure. As a first step,
remove the old cpufreq_debug_printk() function and replace it with a call
to the generic pr_debug() function.
How can dynamic debug be used on cpufreq? You need a kernel which has
CONFIG_DYNAMIC_DEBUG enabled.
To enabled debugging during runtime, mount debugfs and
$ echo -n 'module cpufreq +p' > /sys/kernel/debug/dynamic_debug/control
for debugging the complete "cpufreq" module. To achieve the same goal during
boot, append
ddebug_query="module cpufreq +p"
as a boot parameter to the kernel of your choice.
For more detailled instructions, please see
Documentation/dynamic-debug-howto.txt
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Dave Jones <davej@redhat.com>
The meaning of CONFIG_EMBEDDED has long since been obsoleted; the option
is used to configure any non-standard kernel with a much larger scope than
only small devices.
This patch renames the option to CONFIG_EXPERT in init/Kconfig and fixes
references to the option throughout the kernel. A new CONFIG_EMBEDDED
option is added that automatically selects CONFIG_EXPERT when enabled and
can be used in the future to isolate options that should only be
considered for embedded systems (RISC architectures, SLOB, etc).
Calling the option "EXPERT" more accurately represents its intention: only
expert users who understand the impact of the configuration changes they
are making should enable it.
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Greg KH <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is always "an" if there is a vowel _spoken_ (not written).
So it is:
"an hour" (spoken vowel)
but
"a uniform" (spoken 'j')
Signed-off-by: Frederik Schwarzer <schwarzerf@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Allow use of the powersave cpufreq governor as the default one for EMBEDDED
configs.
Signed-off-by: Alessandro Guido <alessandro.guido@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>
cpufreq support can't be built as a module. Fix the related configuration
help message.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: Dave Jones <davej@redhat.com>
Depending on the transition latency of the HW for cpufreq switches, the
ondemand or conservative governor cannot be used with certain cpufreq
drivers. Still the ondemand should be the default governor on a wide range
of systems. This patch allows this and lets the governor fallback to the
performance governor at cpufreq driver load time, if the driver does not
support fast enough frequency switching.
Main benefit is that on e.g. installation or other systems without
userspace support a working dynamic cpufreq support can be achieved on most
systems by simply loading the cpufreq driver. This is especially essential
for recent x86(_64) laptop hardware which may rely on working dynamic
cpufreq OS support.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Adds proper lines to help output of kconfig so people can find the module names.
Also fixed some broken leading spaces versus tabs.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Dave Jones <davej@redhat.com>
CPU_FREQ_TABLE enables helper code and gets select'ed when it's required.
Building it as a module when it's not required doesn't seem to make much sense.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Update LART site URL.
The LART website moved to http://www.lartmaker.nl/. This patch
updates the URL in CpuFreq specific files.
Signed-off-by: Erik Mouw <erik@bitwizard.nl>
Signed-off-by: Dave Jones <davej@redhat.com>
A new cpufreq module, based on the ondemand one with my additional patches
just posted. This one is more suitable for battery environments where its
probably more appealing to have the cpu freq gracefully increase and decrease
rather than flip between the min and max freq's.
N.B. Bruno Ducrot pointed out that the amd64's "do have unacceptable latency
between min and max freq transition, due to the step-by-step requirements
(200MHz IIRC)"; so AMD64 users would probably benefit from this too.
Signed-off-by: Alexander Clouter <alex-kernel@digriz.org.uk>
Signed-off-by: Dave Jones <davej@redhat.com>
This comes up time and time again. Until its fixed, place this
comment in the Kconfig which should stem the flow of resubmissions.
Signed-off-by: Rob Weryk <rjweryk@uwo.ca>
Signed-off-by: Dave Jones <davej@redhat.com>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
