EXIT_SNK_BASED_ON_CC bit is only to be used while we are in hard
reset. There is a possibility for that bit to remain set if
cable were removed while a hard reset was in progress.
Clear that bit in removal path
Change-Id: I5e0776de9322a8015f851312df51a202e35c7a78
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
The virtual planes are used to support wider HDMI display. Enable
them on msm8996 auto platforms in order to support 4K HDMI display.
Change-Id: I61bf00975ffac73c37f66dbc47dcc11b31df45df
Signed-off-by: Thomas (Wonyoung) Yun <wyun@codeaurora.org>
When calling smmu mapping, if iova is specified directly by user, not
allocated dynamically in dma-mapping.c, smmu driver needs to provide
support for this. This is needed in early display case. In this scenario,
LK has set physical memory to display hardware for fetching, so if iova
is not explicitly specified in kernel, but instead dynamically produced
by "alloc_iova" in dma-mapping.c, display hardware has no chance to know
this new iova, then smmu fault will happen if enabling the iommu stage-1
translation.
To fix this smmu fault problem, add re-routing to the right path when
iova specified by user is not 0 in smmu map/unmap function.
Change-Id: I062b04d7eec65af1c106a5caa09ec787b5d26d0d
Signed-off-by: Guchun Chen <guchunc@codeaurora.org>
USB connector HW based thermal regulation is active which will throttle
the input current on USBIN-USBIN configurations. This was enabled for
MID-MID configurations to enable the comparator output for USB connector
temperature mitigation, but since the input is bypassed it does not
throttle the input current. The comparator output is no longer used
since the ADC values are used directly, so neither configuration needs
this HW feature to be enabled.
Remove the write to enable this HW feature.
Change-Id: Ia7f6b3812ae222fbd8233d07dd6daa67e65ce08b
Signed-off-by: Nicholas Troast <ntroast@codeaurora.org>
As per USB PD 3.0 specification the 2-bit Specification Revision field
of a GoodCRC Message does not carry any meaning and Shall be considered
as don't care by the recipient of the Message. Hence set spec revision
to USBPD_REV_20 for GoodCRC message. PD protocol message header defaults
to USBPD_REV_20 which gets updated USBPD_REV_30 if PD 3.0 source capabale
of programmable power supply.
Change-Id: I5209bb00c437f3c959d093a972f1ac75233cbcf9
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Sigdet under low power (LP) mode will use a less accurate local reference
generation, which is expected to have a little more variation than a
precise reference (normal mode). Update PCIe PHY sigdet to use normal
mode instead of LP to increase accuracy and make sigdet more robust.
Change-Id: If9cad9ac9b5a6a736e3af653ac3b3b5e30cfefb4
Signed-off-by: Tony Truong <truong@codeaurora.org>
Update device tree nodes to support audio on guest virtual machine.
Change-Id: Id2e12b466cff43d8ddcb5c01ecd7bb1a7f0ba04c
CRs-fixed: 2047317
Signed-off-by: King Tam <kingt@codeaurora.org>
Allow re-configuring the DSI, DP and HDMI RCGs even if their
current configuration matches that of the requested frequency.
This is to work around the MM RCGs being latched to run off of
XO by default after an MM GDSC power collapse.
Change-Id: Idf5f1f25df6d6a8ef29eb8c15086deba1017584e
Signed-off-by: Deepak Katragadda <dkatraga@codeaurora.org>
