Automotive use case requirement is to have HDMI display as non-pluggable.
This change also set a custom mode as 1920x1080p@60Hz.
Change-Id: Ic2baec180d51dc6a91eaf72c44df1da066f04d2e
Signed-off-by: Rahul Sharma <sharah@codeaurora.org>
Update the arp and ns tuple for arp-ns tlv cmd and pass
the size of IP address and wlan net dev name during mem
copy and comparison.
CRs-Fixed: 2149966
Change-Id: I9457af4578c70f876c3a58e3d8c655dcaa476e07
Signed-off-by: Sarada Prasanna Garnayak <sgarna@codeaurora.org>
Add device pointer in all export symbol to
add support for numerous WLAN module.
CRs-Fixed: 2138446
Change-Id: I981155c165e4e5c2794b778afe647f8a588dd860
Signed-off-by: Sarada Prasanna Garnayak <sgarna@codeaurora.org>
If same event is unsubscribed before v4l2_event_subscribe returned,
Then function v4l2_event_subscribe have possibility use-after-free.
Serialize msm_subscribe_event and msm_unsubscribe_event to
prevent parallel invocation of v4l2_event_subscribe and
v4l2_event_unsubscribe.
Change-Id: Ia28cfb9d46550d58221f157337a1468f524753e3
Signed-off-by: Trishansh Bhardwaj <tbhardwa@codeaurora.org>
HL1.0 firmware sends phyerr_mask in the phyerr
event, which needs to be used to determine the
type of phyerr.
Add the phyerr_mask parameters for HL1.0 in the
phyerr wmi event.
CRs-Fixed: 2150566
Change-Id: Ib2d5286fbf45d41229e68d817d65714d18811a4e
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
This is a fix for dynamic memory leak seen with incorrectly
allocating memory of a different size than with intended
size.
Change-Id: I821442ee6728ea90ceab7644e194f4e06369333a
Acked-by: Jyothi Jayanthi <jyothij@qti.qualcomm.com>
Signed-off-by: Michael Adisumarta <madisuma@codeaurora.org>
For non-pluggable display, it should not enable HPD. Instead, the
bridge should handle all the clocks for HDMI. Also the scrambler
should be activated after the HDMI has power on the clock.
Change-Id: I9162a49b8f314de4d30b0d82c7867a639ddf05a6
Signed-off-by: Camus Wong <camusw@codeaurora.org>
Compile ADV7481 as a module, as part of kernel modularization
requirement.
Change-Id: Ie3e9669d05646503de6ddd3468cbd6da4ee4eae4
Suggested-by: Resmi Rajendran <resmir@qti.qualcomm.com>
Signed-off-by: Rahul Sharma <sharah@codeaurora.org>
In slave configuration "POWER_SUPPLY_PROP_CURRENT_MAX" fails to
suspend USB input path for 0/2mA current request. Fix this by
separately handling 0/2mA request to suspend input.
CRs-Fixed: 2148379
Change-Id: Id9b7887c4f2f924d9e4c8484947d74baa96eb8a3
Signed-off-by: Ashay Jaiswal <ashayj@codeaurora.org>
Current parallel design has fixed order of configuring
ICL/FCC between main and parallel charger, this could
lead to a situation where total(main + parallel) ICL/FCC
goes beyond maximum configured value.
Fix this by dynamic ordering of ICL/FCC between main and
parallel based on AICL change.
CRs-Fixed: 2148379
Change-Id: Ia1ff7093d1de9205ce8072760c80ba0a58638462
Signed-off-by: Ashay Jaiswal <ashayj@codeaurora.org>
Remove "qcom,mdss-dsi-on-command" and "mdss-dsi-off command"
commands for boot up performance optimization.
The two commands are for native DSI panels without a bridge
chip. However,AUTO platform has adv7533 bridge chip,which
is controlled by I2C instead of the above two commands.
In addition,the two command will cause extra wait for about
210ms in dsi_panel_tx_cmd_set() for dsi_display_enbale().
This make drmAtomicCommit() in libdrm a little slower,
so total boot time will be longer.
Change-Id: I848d189d4055b5626eadd809fc5da7c9c4ecbcce
Signed-off-by: Daocai <daocai@codeaurora.org>
In current HDMI driver, SVDs and DTDs derived from EDID
of a DS HDMI sink are checked for supportness based
on previous connection's max TMDS clock.
Always reset the max TMDS clock supported by source
before reading EDID from DS HDMI device.
Change-Id: If5f58562f186634b1ed066fdebfc9fa6b55c6e8a
Signed-off-by: Narender Ankam <nankam@codeaurora.org>
Hypervisor supports psci-1.0 not 0.1 and new function IDs
have been defined in psci driver.
Change-Id: Id257dd264f9ffc812879997c0b227e53f84c86a2
Signed-off-by: Yimin Peng <yiminp@codeaurora.org>
