This reverts commit 9ec3ce38d7.
This change brings one NULL pointer in display kernel booting, which
will bring crash on msm8996 lite board. So revert this commit temporarily.
Change-Id: I7e11b78b47f0e2f2f5cc05a0220f1ff7f3a1addd
Signed-off-by: Guchun Chen <guchunc@codeaurora.org>
Add a device specific flag for new vmid heap shared feature.
Change-Id: I9be679f9edd0048acbb057ceff4d877c630e4258
Signed-off-by: Tharun Kumar Merugu <mtharu@codeaurora.org>
Only HDMI INTF3 should need cdm block, other
INTFs do not need cdm.
Change-Id: Iff355dae456ed432efd84dff72ec85b83dbb93f2
Signed-off-by: Yuan Zhao <yzhao@codeaurora.org>
Since 'timestamp' is of unsigned int type, for larger timestamp
the format specifier %d can show negative values. Fix this by
using %u format specifier for timestamp.
Change-Id: I621dfd4843099cb27436006500fe3342d1d5ddf4
Signed-off-by: Abhilash Kumar <krabhi@codeaurora.org>
Provide support to enable/disable sw jeita using a power supply
property.
Change-Id: Id1c2a4bcd8caece5ed7591dc5ab5bf3ac2207cba
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Disable sending dummy BDF(board data file). Enforce to use real BDF
by default.
Change-Id: Ib0cf267af8ddea8a702f8ac6774063466094f52e
CRs-fixed: 2059087
Signed-off-by: Yue Ma <yuem@codeaurora.org>
On each sg of secure CMA buffer to set/clear page private bit,
we should use the sg_page(sg) rather than sg_page(sgt->sgl).
Change-Id: I05300d9d3a0931d2a0c113f945b45136e0dea01e
Signed-off-by: Hareesh Gundu <hareeshg@codeaurora.org>
Core IPA driver passes wrong end-point index to HAL
when generating aggregation force close parameters
values. Fixed the call to pass the correct index.
CRs-Fixed: 2082839
Change-Id: Icc0fd2ce8a23bf0e3334f54b27b850ebf92b58a1
Signed-off-by: Ghanim Fodi <gfodi@codeaurora.org>
Use mutex lock for all VB2 operations, and use separatelock other
than used for stop streaming operation to avoid dead lock.
Change-Id: Idba956e5e3bce48ee57eaa5984786ded218e32d5
Signed-off-by: annamraj <annamraj@codeaurora.org>
After finishing initialization during PCIe probe, there is no need to
keep PCIe link up. Hence suspend PCIe link and power off device after
PCIe probe for QCA6290 chipset.
Change-Id: I1b07d7c9ef4c3a15ba1eb409a4c64f905e83dae4
Signed-off-by: Yue Ma <yuem@codeaurora.org>
The vibrator HAL expects vibration to be disabled when the 'enable'
time specified is 0. Fix this.
CRs-Fixed: 2083994
Change-Id: I12843233da5429ed2fd53f33617952b1dd0ddcd5
Signed-off-by: Anirudh Ghayal <aghayal@codeaurora.org>
When there is an early charge termination because of soft JEITA
(warm and cool) conditions, float voltage would have been reduced
by the charger based on the compensation configuration (e.g. by
105 mV). This can be close to the recharge voltage threshold
(e.g. 4.25 V) when the recharge is configured to be based off
Vbatt. Adjust the recharge voltage threshold dynamically by
lowering it by 200 mV during soft JEITA and charge termination.
Reset it back to the original value when the condition clears
i.e. either it is out of soft JEITA or the charger is removed.
Change-Id: If4d293c10e84e414c81204784f2e7062140264b1
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
Currently, when scrambler is disabled the TMDS clock ratio bit
is left untouched. Ideally the sink should reset this bit during
hot plug OR no-signal cases. However, the HDMI spec requires this
bit to be explicitly reset by the source.
Add support to reset this bit during scrambler disable.
Change-Id: I092f6cae84653940e2bdb9100df5e384084cf938
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
As per SMC Calling Convention, X4/W4, X5/W5 & X6/W6 registers
return state is unpredictable. But, inline assembly in scm
driver did not correctly specify output markers, which is
causing compiler to move instructions around when clang is
used to compile, which inturn causing deadlock and boot issue
during firmware loading. Add X4/W4, X5/W5 & X6/W6 registers
to output operand list to fix the deadlock during firmware
loading.
Change-Id: I1e4d51a58cd34c31fc63bcd21a20bfd15498bdc3
Signed-off-by: Satya Durga Srinivasu Prabhala <satyap@codeaurora.org>
PD down notifications reaches APPS only after WLAN HW is
reset. Because of this, there is a small window of time
in which APPS may try to access WLAN HW Copy Engine
registers and get into exception. To avoid this, FW has
implemented 2 stage reset sequence in which first HW is
halted rather than reset and then when FW PD is started
again, reset sequence is executed. Because of the 2
stage reset sequence, WLAN shutdown call back also needs
to be delayed as there may be some buffers submitted to
hardware and if they are freed then again HW exception
may be seen. Delay the shutdown call back till FW ready
happens at this time HW should be reset and clean state.
CRs-fixed: 2056443
Change-Id: Ie587f98d574f7c0a49a8480449fed44c1f4ab816
Signed-off-by: Anurag Chouhan <achouhan@codeaurora.org>
