This reverts 'commit 7112993181 ("input: touchscreen: synaptics v1.1")'
This change is not needed in 4.4 kernel.
Change-Id: I89ab8f353bc04bc0a04d5f5a6993e8e8e5ebbd2e
Signed-off-by: Abinaya P <abinayap@codeaurora.org>
Signed-off-by: Shantanu Jain <shjain@codeaurora.org>
Set LAB's precharge time to max 500us to optimize the precharge
behavior as suggested in the hardware documentation.
CRs-Fixed: 1084297
Change-Id: I118f4254686caf498087847916b7710662ab31e7
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
Currently, some properties in LABIBB regulator driver are having
prefix "qpnp" which is not reflecting the vendor. Change it to
"qcom" to reflect the vendor name correctly and also match with
other DT properties.
CRs-Fixed: 1071971
Change-Id: I182dddc29f3d7c7b449b56ac7fb84e74061cf3a4
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
For LABIBB peripherals in pmicobalt, bootloader configures
LCD/AMOLED mode and SWIRE control based on a GPIO selector.
Hence, add support to configure them selectively.
While at it, fix the variable name used in read/write APIs to
reflect the address rather than base. Also use the pmic subtype
macros from qpnp-revid.h directly.
CRs-Fixed: 1071971
Change-Id: Ibbf3d432709eadf0808e062726804be6b2a065ee
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
Lock out interrupts during issuing dummy request in timeout to prevent from
a potential deadlock happening.
Change-Id: I986d8c36c839a1dee23761465ad331ffc31dd6ac
CRs-Fixed: 1008319
Acked-by: Che-Min Hsieh <cheminh@qti.qualcomm.com>
Signed-off-by: Yasir Malik <ymalik@codeaurora.org>
Convert most of the pmfalcon stub-regulator devices to a
rpm-smd-regulator devices. This ensures that requests made for
these regulators are aggregated by the RPM processor along with
the requests from other processors.
Also, add a dummy gfx_vreg_corner regulator until the CPR node
is added.
While at it, rename all regulators names and add pm/pm2 prefix
to differentiate between regulators on multiple supported PMICs.
Also update all clients with new regulator phandles.
CRs-Fixed: 1077493
Change-Id: I95b17de5bf17b62096d2c9d60633b6b30768752a
Signed-off-by: Ashay Jaiswal <ashayj@codeaurora.org>
Since usleep_range provides better accuracy in
comparison to msleep. This helps in reducing the
latency of host bus resume.
Change-Id: Id22104b9e5b63153731df9eb55759de9a86128c6
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
A540v1 and v2 both need to enable the LMLOADKILL quirk for the
GPU.
CRs-Fixed: 1036444
Change-Id: I84243578a1ef2f9948f0c9a8c1c00dc6a31eb579
Signed-off-by: Harshdeep Dhatt <hdhatt@codeaurora.org>
Add a quirk to set LMLOADKILLDIS bit in A5XX_VPC_DBG_ECO_CNTL
and clear LMLOADKILLDIS bit in A5XX_HLSQ_DBG_ECO_CNTL registers.
This is done to avoid a VPC corner case with local memory(LM)
which leads to corrupt internal state on A540 and its derivatives.
CRs-Fixed: 1036444
Change-Id: I31008433f19924bb35560d3e35fe0665e73751d5
Signed-off-by: Harshdeep Dhatt <hdhatt@codeaurora.org>
Embedded tputs depend on WAN RX desc size, but, every target
has its own limitations of memory and embedded tputs goals.
So, add parameter to configure WAN RX desc size through device tree.
Change-Id: I28c550058dd990c9c8cd368a2677097c7f057ccd
CRs-Fixed: 1081543
Signed-off-by: Sunil Paidimarri <hisunil@codeaurora.org>
Based on the hardware documentation, update the IMA error
handling and clear sequence. In addition, check for DMA errors
and clear it before SRAM transactions begin. Also, check for IMA
hardware status to run the IMA clear sequence during ima_init and
not just based on IMA exception status alone. This is to help
with FG SRAM access to resume again properly in case of an error
encountered.
Change-Id: I583fa51599a1cbbd029cb45c075429730d2e071b
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
