Exynos PCIe IP consists of Synopsys specific part and Exynos
specific part. Only core block is a Synopsys Designware part;
other parts are Exynos specific.
Also, the Synopsys Designware part can be shared with other
platforms; thus, it can be split two parts such as Synopsys
Designware part and Exynos specific part.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Mohit KUMAR <Mohit.KUMAR@st.com>
Enable the HDMI output as well as DDC and hotplug detection on Beaver.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
There was a typo in the base address used for the soc node in the A13
device tree. Fix it with the proper base address.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The reg property of the simple-bus driver is completely useless. Remove
it from the DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
There was a typo in the base address used for the soc node in the A10s
device tree. Fix it with the proper base address.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The reg property of the simple-bus driver is completely useless. Remove
it from the DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
There was a typo in the base address used for the soc node in the A10
device tree. Fix it with the proper base address.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The reg property of the simple-bus driver is completely useless. Remove
it from the DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This driver is currently used by musb' cppi41 couter part. I may merge
both dma engine user of musb at some point but not just yet.
The driver seems to work in RX/TX mode in host mode, tested on mass
storage. I increaed the size of the TX / RX transfers and waited for the
core code to cancel a transfers and it seems to recover.
v2..3:
- use mall transfers on RX side and check data toggle.
- use rndis mode on tx side so we haveon interrupt for 4096 transfers.
- remove custom "transferred" hack and use dmaengine_tx_status() to
compute the total amount of data that has been transferred.
- cancel transfers and reclaim descriptors
v1..v2:
- RX path added
- dma mode 0 & 1 is working
- device tree nodes re-created.
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <djbw@fb.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This moves the two instances from the big node into two child nodes. The
glue layer ontop does almost nothing.
There is one devices containing the control module for USB (2) phy,
(2) usb and later the dma engine. The usb device is the "glue device"
which contains the musb device as a child. This is what we do ever since.
The new file musb_am335x is just here to prob the new bus and populate
child devices.
There are a lot of changes to the dsps file as a result of the changes:
- musb_core_offset
This is gone. The device tree provides memory ressources information
for the device there is no need to "fix" things
- instances
This is gone as well. If we have two instances then we have have two
child enabled nodes in the device tree. For instance the SoC in beagle
bone has two USB instances but only one has been wired up so there is
no need to load and init the second instance since it won't be used.
- dsps_glue is now per glue device
In the past there was one of this structs but with an array of two and
each instance accessed its variable depending on the platform device
id.
- no unneeded copy of structs
I do not know why struct dsps_musb_wrapper is copied but it is not
necessary. The same goes for musb_hdrc_platform_data which allocated
on demand and then again by platform_device_add_data(). One copy is
enough.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The pcie-controller node needs to be relocated according the MBus
DT binding, since it's now a child of the mbus-compatible node.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
There are a number of variants of the ZyXEL NSA310, with slightly
different LEDs, buttons and i2c devices. Add a DTS file to support one
more of these variants.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Tibor Hársszegi <tibor@harsszegi.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The ranges property needs to be changed to use the new MBus DT binding.
Also, the pcie-controller node needs to be relocated as according the MBus
DT binding, it's now a child of the mbus-compatible node.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The AXP WiFi AP board is a Marvell platform based on the Armada XP
MV78230 SoC. It has two mini-PCIe connectors, one USB 3.0 port powered
by a USB 3.0 controller on PCIe, two Ethernet ports, 1 GB of RAM, 1 GB
of NAND, 16 MB of SPI flash, one SATA port and one button, two UARTs
Successfully tested: USB 3.0 port, the mini-PCIe connectors, SPI
flash, Ethernet ports, SATA port, button, UART.
Untested: NAND flash, due to lack of mainline support for the Armada
370/XP NAND controller for now.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Seif Mazareeb <seif@marvell.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Update the reg property of the memory node in
skeleton64.dtsi to reflect the fact that the root node uses
address-cells=2 and size-cells=2.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
SCC (Serial Configuration Controller) is used to set initial
conditions for the test chip (TC2). Its registers are also mapped
in normal address space and used to obtain runtime information
and for power management.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
This must have been a merge error. There was a patch which renamed the
u9540.dts to ccu9540.dts, however the u9540.dts was reincarnate with
the same patches which created it in the first place. Let's kill it
once and for all.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
It doesn't exist on the Snowball development board.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
TPS61052 is a; boost converter, LED driver, LED flash driver and
simple GPIO pin chip. It has no use here however, as it is not
found on the Snowball development board.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
It doesn't exist on the Snowball development board.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
It doesn't exist on this development board.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Instead of using bit-banged I2C, let's use the actual I2C
driver in the kernel. Since the I2C block may be communicating
with things like the PMIC, we need to select it from the Kconfig
just like the bit-banged adapter is selected today. The rest of
the configuration for this driver can be done from the device
tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds the device tree bindings for the bcm281xx reboot code.
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Acked-by: Christian Daudt <csd@broadcom.com>
This patch configures pin map in device tree of i2c0,
1,2,4 & 5 for ccu8540 board.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds pinctrl device tree settings for uart0 and uart2
for ccu8540 board.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Regulator names are platform independent, so they need to be applied to
the base level platform DTS files *.dts. Here we're supplying the names
for the newly described AB8500 external regulators.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
AB8500 AUX regulators are supplied by EXT3 on some boards. This supply
phandle lookup will enable the regulator core to search for and locate
the EXT3 supply at registration time.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The AB8500 has 3 external regulators which are used to control outside
voltage sources. Some of the core AB8500 use these external regulators
as a supply, so they must be obtainable via Device Tree.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit converts the mv88f6281gtw_ge Kirkwood board to use a
Device Tree representation, except for the Ethernet devices and the
DSA switch. Even though the mv643xx_eth driver has a DT binding,
converting this board to use it is for now left on the side because it
doesn't use a simple PHY, but a DSA switch instead.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add MAX8998 LDO12 and fixed voltage regulator nodes. While at it,
all fixed voltage regulator nodes are grouped in a 'regulators' node.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add pinctrl nodes for the camera parallel port CAM_A data bus
and the CAM_A_CLKOUT clock output pin.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Enable FIMC devices on the Trats board. This allows using the
device in memory-to-memory mode only. The camera port pinctrl
property is now empty and will be updated while support for the
camera sensors is added.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add common camera node and detailed properties for
the Exynos4210 FIMC devices.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch add dts entries required for the SPI bus used for
firware upload by the S5C73M3 camera.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Now that mbus has been added to the device tree, it's possible to
move the PCIe nodes out of the ocp node, placing it directly
below the mbus. This is a more accurate representation of the hardware.
Moving the PCIe nodes, we now need to introduce an extra cell to
encode the window target ID and attribute. Since this depends on
the PCIe port, we split the ranges translation entries, to
correspond to each MBus window.
In addition, we encode the PCIe memory and I/O apertures in the MBus
node, according to the MBus DT binding specification. The choice made
is 0xe0000000-0xf0000000 for memory space, and 0xf200000-0xf2100000 for
I/O space. These apertures can be changed in each per-board DT file.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This macro is used to define window's target ID and attribute cells
for the MBus ranges entries.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add a minimal MBus node, just to allow the MBus driver to probe.
Follow-up patches will migrate the rest of the nodes appropriately.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
