Add mdio device tree node information to da850 by
providing register details and bus frequency of mdio.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The sam9x5ek board has 2 jacks:
headphone wired on RHPOUT/LHPOUT of the wm8731
line in wired on LLINEIN/RLINEIN of the wm8731
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Enable the SSC needed for the WM8731 codec
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The WM8731 codec on sam9x5ek board is on i2c, address 1A
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The PQFP version have only 3 gpio banks (A, B & C).
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[nicolas.ferre@atmel.com: correct typo in "status" property]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Correct pin number of gpio-key for at91sam9n12ek board.
The pioB4 is connect to LED, the pioB3 use as gpio-key.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
ARM Performance Monitor Units are available on the sama5d3, add the support in
the dtsi.
Tested with perf and oprofile on the sama5d31ek.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
pinctrl-names was missing causing mmc pinctrl to never be requested.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
[nicolas.ferre@atmel.com: added a commit message taken from Ludovic]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add DT property to tell the regulator to register pm_power_off to make
"shutdown" work.
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
This branch contains all *.dts (device tree) changes for Tegra.
New features enabled are:
* PMICs on Dalmore
* CPU power-gating on Dalmore
* HDMI output on Beaver
* LP1 system suspend mode on almost all boards
* PCIe support on numerous Tegra20/30 boards
* USB support on Tegra30/114 boards
* Audio capture on Beaver and Dalmore
* Temperature sensor on Cardhu.
... along with a few DT cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=RGgU
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.12-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/dt
From: Stephen Warren:
ARM: tegra: device tree changes for 3.12
This branch contains all *.dts (device tree) changes for Tegra.
New features enabled are:
* PMICs on Dalmore
* CPU power-gating on Dalmore
* HDMI output on Beaver
* LP1 system suspend mode on almost all boards
* PCIe support on numerous Tegra20/30 boards
* USB support on Tegra30/114 boards
* Audio capture on Beaver and Dalmore
* Temperature sensor on Cardhu.
... along with a few DT cleanups.
* tag 'tegra-for-3.12-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (25 commits)
ARM: tegra: add Mic Jack to Dalmore device tree
ARM: tegra: add Mic Jack to Beaver device tree
ARM: tegra: add USB DT entries for Tegra114, Dalmore
ARM: tegra: add USB DT entries for Tegra30
ARM: dts: tegra: Increase prefetchable PCI memory space
ARM: tegra: Fix Beaver's PCIe lane configuration
ARM: tegra: Enable PCIe controller on Beaver
ARM: tegra: Enable PCIe controller on Cardhu
ARM: tegra: Add Tegra30 PCIe support
ARM: tegra: trimslice: Initialize PCIe from DT
ARM: tegra: harmony: Initialize PCIe from DT
ARM: tegra: tec: Add PCIe support
ARM: tegra: tamonten: Add PCIe support
ARM: tegra: Add Tegra20 PCIe support to DT
ARM: tegra: enable LP1 suspend mode
ARM: tegra: beaver: Enable HDMI output
ARM: tegra: use TEGRA_GPIO() in a couple more places
ARM: tegra: dalmore: fix the irq trigger type of Palmas MFD device
ARM: tegra: define valid function names in DT document
ARM: tegra: dalmore: add PM configurations for PMC
...
development cycle:
- Various cleanups like remove non-existant hardware from
the Snowball device tree, prefix all files with "ste-*"
- External regulators
- Documentation updates
- Delete some minor dangling platform data
- Pin control settings for U8540 through DT
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=Wm2y
-----END PGP SIGNATURE-----
Merge tag 'ux500-devicetree-for-v3.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
From: Linus Walleij:
Ux500 device tree enablement base for the v3.12
development cycle:
- Various cleanups like remove non-existant hardware from
the Snowball device tree, prefix all files with "ste-*"
- External regulators
- Documentation updates
- Delete some minor dangling platform data
- Pin control settings for U8540 through DT
* tag 'ux500-devicetree-for-v3.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: (22 commits)
ARM: ux500: fix devicetree builds
ARM: ux500: Remove u9540.dts as it's been replaced
ARM: ux500: Apply a ste-* prefix onto dbx5x0.dtsi
ARM: ux500: Apply a ste-* prefix onto stuib.dtsi
ARM: ux500: Apply a ste-* prefix onto hrefv60plus.dts
ARM: ux500: Apply a ste-* prefix onto hrefprev60.dts Signed-off-by: Lee Jones <lee.jones@linaro.org>
ARM: ux500: Apply a ste-* prefix onto href.dtsi
ARM: ux500: Apply a ste-* prefix onto ccu9540.dts
ARM: ux500: Apply a ste-* prefix onto ccu8540.dts
ARM: ux500: Apply a ste-* prefix onto snowball.dts
ARM: ux500: Remove Snowball DTS entry for ROHM BH1780GLI ambient light sensor
ARM: ux500: Remove Snowball DTS entry for TPS61052 chip
ARM: ux500: Remove Snowball DTS entry for National Semiconductor LP5521 LED chip
ARM: ux500: Remove Toshiba TC35892 I/O Expander's DT entry from Snowball's DTS
ARM: u8540: DT: Set pinctrl mapping to i2c0,1,2,4 & 5
ARM: u8540: Add Pinctrl Device Tree settings for uart0, uart2
ARM: ux500: Stop passing MMC's platform data for Device Tree boots
Documentation: Update binding for Nomadik and DBx5x based platforms
ARM: ux500: Supply external regulator names for Snowball's DT
ARM: ux500: Provide a supply name for the AB8500 AUX regulators to use
...
[ this is a follow-up to this discussion:
http://archive.arm.linux.org.uk/lurker/message/20130730.230827.a1ceb12a.en.html ]
This patchset renames all uses of "bcm," name bindings to
"brcm," as they were done prior to knowing that brcm had
already been standardized as Broadcom vendor prefix
(in Documentation/devicetree/bindings/vendor-prefixes.txt).
This will not cause any churn on devices because none of
these bindings have made it into production yet.
Also rename the the following dt binding docs that had "bcm,"
in their name for consistency:
- bcm,kona-sdhci.txt -> kona-sdhci.txt
- bcm,kona-timer.txt -> kona-timer.txt
Signed-off-by: Christian Daudt <csd@broadcom.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Enable sdio for bcm28155 AP board
Signed-off-by: Christian Daudt <csd@broadcom.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Clean up the sdio numbering to be 1-base as defined in HW spec,
instead of the current 0-base
Signed-off-by: Christian Daudt <csd@broadcom.com>
Reviewed-by: Alex Elder <elder@linaro.org>
The Olimex A20-Olinuxino is an open-hardware board based on the
Allwinner A20 SoC, with most of the pins exported on headers, a 10/100M
ethernet port, SATA, SD and uSD slots, etc.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner A20 SoC is based on 2 Cortex A7, an ARM Mali GPU, and is
built to be pin-compatible with the older Allwinner A10.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=BR17
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.12/dra7xx' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
From Tony Lindgren:
Minimal DRA7xx based SoC core support via Rajendra Nayak <rnayak@ti.com>
* tag 'omap-for-v3.12/dra7xx' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (849 commits)
ARM: DRA7: Add the build support in omap2plus
ARM: DRA7: hwmod: Reuse the soc_ops used for OMAP4/5
ARM: DRA7: id: Add cpu detection support for DRA7xx based SoCs'
ARM: DRA7: Kconfig: Make ARCH_NR_GPIO default to 512
ARM: DRA7: board-generic: Add basic DT support
ARM: DRA7: Resue the clocksource, clockevent support
ARM: DRA7: Reuse io tables and add a new .init_early
ARM: DRA7: Reuse all of PRCM and MPUSS SMP infra
Linux 3.11-rc5
btrfs: don't loop on large offsets in readdir
Btrfs: check to see if root_list is empty before adding it to dead roots
Btrfs: release both paths before logging dir/changed extents
Btrfs: allow splitting of hole em's when dropping extent cache
Btrfs: make sure the backref walker catches all refs to our extent
Btrfs: fix backref walking when we hit a compressed extent
Btrfs: do not offset physical if we're compressed
Btrfs: fix extent buffer leak after backref walking
Btrfs: fix a bug of snapshot-aware defrag to make it work on partial extents
btrfs: fix file truncation if FALLOC_FL_KEEP_SIZE is specified
dlm: kill the unnecessary and wrong device_close()->recalc_sigpending()
...
Signed-off-by: Kevin Hilman <khilman@linaro.org>
From Jason Cooper, mvebu fixes-non-critical for v3.12 (round 2):
- fix the memory node (2 by 2) in skeleton64.dtsi
* tag 'fixes-non-3.12-2' of git://git.infradead.org/linux-mvebu:
ARM: dts: Fix memory node in skeleton64.dtsi
This patch adds EHCI and OHCI host device nodes for Exynos4.
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This adds device-tree bindings for the audio subsystem clock controller
on Exynos 5420.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57712
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch corrects the /include to #include on exynos5420
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The patch adds the MFC clock entry for the 5250 SoC.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Removes the unused sclk_mfc from exynos4 dtsi file.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
While the Linux driver stack is capable of figuring this out for itself
document the fact that we really do use the internal PHY even with the
directly wired hub on the board to save anyone else having to work this
out for themselves.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The Arndale has a SMSC USB3503 connected in hardware only mode like a PHY,
support it using the usb-nop-xceiv binding.
Note that due to a regrettable decision to use a regulator to represent
the reset signal this uses a fixed voltage regulator to do that, there
is a plan to use the reset controller binding once that is merged so it
does not seem worthwhile to fix the usb-nop-xceiv driver at this point.
Signed-off-by: Mark Brown <broonie@linaro.org>
Tested-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
OrigenQuad board boots with secure firmware support. Enable support for
reading smc commands.
The binding has been updated as per the documentation provided in
Documentation/devicetree/bindings/arm/samsung-boards.txt.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add pin state information for DP HPD support that requires pin configuration
support using pinctrl interface.
Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Moves the properties of DP controller to exynos5.dtsi which are common
across exynos5 SoCs like Exynos5250 and Exynos5420.
The PHY DP Node is based on Jingoo Han's <jg1.han@samsung.com> patch
at https://patchwork.linuxtv.org/patch/19189/
Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Adds FIMD DT node to exynos5420 based SMDK. Also adds display-timimg
information node.
Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Moves the properties of FIMD DT node which are common across Exynos5 based
SoCs like Exynos5250 and Exynos5420 to exynos5.dtsi
Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
As the display-timing information is parsed by FIMD driver, it makes
sense to move the display-timing DT node inside FIMD DT node for exynos5250
Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This platform from WITS is the evaluation board for the Allwinner A31.
It features a quad-Cortex A7, 2048MB of RAM, NAND, USB, MMC, several
UART, HDMI, a 2048 x 1536 10" screen, powered by a PowerVR, etc.
Of course, most of these peripherals aren't supported yet, but support
for those will come eventually.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The "marvell,armada-370-xp-timer" compatible string, together with
the "marvell,timer-25Mhz" property are deprecated and should be
removed from current DT.
Instead, the timer DT nodes are now required to have an appropriate
compatible string, which should be either "marvell,armada-370-timer"
or "marvell,armada-xp-timer", depending on SoC.
The clock property is now required only for Armada 370 so move it accordingly.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Device Tree information for the GPIO banks of the Armada 370 and
Armada XP SOCs was incorrectly using #interrupts-cells instead of
controller when using GPIO interrupts, since the GPIO bank DT node
wasn't recognized as a valid interrupt controller by the OF code.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch removes quirks from i2s node and change the i2s
compatible names.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
